ND0A0 Product Introduction Quick installation Ethernet Port (Optional) Type C Port Threading Position Reset Hole (Optional) USB Port 1 3 Ethernet Port (Optional) Used for Ethernet access, offer network to P2 via WiFi. And the POS Base can be connected to P2 without any setting. Reset Hole (Optional) Used for reset POS Base WiFi. Threading Position Used to constrain the card position of the peripheral connection, making the cable more orderly. USB Port 2 USB ports, used for peripheral connection, such as scan code gun, keyboard, mouse and etc. Type C Port Supply power for P2 and POS Base. 2 Insert cable port into the Type C port, Ethernet port (insert the network cable if have);
1 Connect the adapter to the mains 2 Put P2 on POS Base, then start charging, or access internet through the POS Base (optional) 3 If you need to change the WiFi configuration of the POS Base, enter P2 settings,Wireless and Network - More, POS Base Settings. Charging and Display Instructions This machine only supports 5V/2A 3A Type C cable charging. When charging, the screen will display the corresponding icon. Precautions Product Technical Indicators Safety Warning Plug the AC plug into an AC outlet that corresponds to the identification input on the accessory power adapter;
It is strictly forbidden to use in places where there is any potential explosive gas;
Non-professionals should not open the power adapter at will to avoid danger;
This is a Class A product. In a living environment, this product may cause radio interference. In this case, the user may be required to take practical measures for interference. Important Safety Instructions When you notice an unusual smell, overheating or smog, turn off the power immediately. Suggestions Do not use in a wet environment near water or lake and avoid liquids falling into the terminal; Do not use in extremely hot and cold environments, such as near fire or lit cigarettes;
Do not drop, throw or bend;
Try to use it in a clean, dust-free environment to prevent small items from falling into the terminal;
Do not use it near medical equipment without permission. Statements The company is not responsible for the following actions Damage caused by use and maintenance without the conditions described in this guide;
The company will not be responsible for any damages or problems caused by the alternatives or consumables (not the original products or approved products provided by the company). Without consent of the company. It is not authorized to make product modifications or changes. Disclaimer Due to product updates, some details of this document may not match the product, please refer to the actual product, and the right to interpret this document belongs to the company. The right to modify this guide without prior notice is reserved. Items Technical Specifications Interface 2 x USB Type-A port, 5V/500mA, Ethernet Port(optional) Charger Input: AC110~220V/0.3~0.4A Output: DC5V/2A. USB Type-C port Size 227mm 96mm 49mm Working Environment Working Temperature: 0~40 Storage Temperature: -20~70 WLAN 2.4G 802.11 b/g/n Max. radio-frequency power transmitted 802.11b/g/n20dBm Common Troubleshooting If the connecting bullet does not come up, it needs to be sent for after-sales maintenance. If not charges, check if the Type C port is inserted in place, if still cannot get charged after putting it in place, you need to check of the charging cable or power supply is damaged. If the pedestal WiFi function is abnormal, use the tool to press and hold the reset hole for 3 seconds. FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To comply With RF exposure requirements, a minimum separation distance of 20cm must be maintained between the users body and the POS machine, including the antenna. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. EU Regulatory Conformance Hereby, Shanghai Sunmi Technology Co., Ltd. declares that the radio equipment type is in compliance with Direc- tive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
www.sunmi.com Manufacture Shanghai Sunmi Technology Co., Ltd. Room 605, Block 7, KIC Plaza, No.388 Song Hu Road Yang Pu District, Shanghai, China Notice: Observe the national local regulations in the location where the device is to beused. This device may be restricted for use in some or all member states of the European Union
(EU). Adapter shall be installed near the equipment and shall be easily accessible. The operating temperature of the device between 0C to 45C. The device complies with RF specifications when the device used at 20cm from your body This product can be used across EU member states.