FCC ID: 2AKPPHLTH8162 R/C DRONE

USED FOR H816, H816C, H816W Sfoicite WAVE RAZOR HIGH PERFORMANCE UFO FOR RC ENTHUSIASTS FLIGHT MANUAL Battery requirements for transmitter:

4X 1.5V AAA size batteries (not included) DRONE is equipped with a Li-Poly rechargeable battery, please also pay attention to the following safety precautions

* Don't use or leave the battery near a heat source such as fire or heater.

* Don't strike or throw the battery against any hard surface.

* Don't immerse the battery in water, and keep the battery in a cool dry place.

* When recharging, only use the battery charger intended for that purpose.

* Don't over-charge the battery.

* Don't directly solder the battery or pierce it with a nail or other sharp object.

* Don't transport or store the battery together with metal objects.

* Never charge the battery for more than one hour

: at Note: =

* Never leave charging battery unattended.

* Always dispose of old batteries responsibly Safety Precautions

* Please read through the manuals before using

* Please store small parts in a place well out of the reach of small children

* Never leave the DRONE unattended during battery charging

* Never throw any batteries in a fire.

* Never fly the DRONE near other people.

+ Keep all body parts away from the copter while the rotor blades are spinning

* Never try to repair circuitry, there are no serviceable electronic inside the DRONE or transmitter.

-1-

Flying Precautions 1.Keep small parts out of the reach of children, to avoid choking hazard. 2.The DRONE is powerful, when taking off, move the throttle stick foreard gradually, to avoid its rising too fast. 3. After flight, turn off the DRONE first, then turn off the controller. 4.Do not put the battery in high temperature or near heat source 5.Note, to avoid injury or damage, the DRONE should not beflown nearer than 2 meters

/7 feet from people or other obstacles. 6.Children should fly the DRONE under adult supervision only. Always keep the DRONE inclear sight while flying. 7.Always turn off the power of the controller and DRONE when not in use. Battery Protection 1.The DRONE is equipped with low-voltage protection: When it's battery is low, the programmed control system will stop electrical supply to DRONE s rotors. The battery then needs charging to allow the DRONE to fly again. Maintenance 1. Clean the DRONE with clean, dry soft cloth only. 2. To avoid irreparable damage, keep the DRONE dry and away from water. Do not fly in rainy conditions. 3. Check the DRONE and accessories for damage. If damage is found, do not use the DRONE until it is repaired Battery Installation & Charging Controller Battery cover 4X 1.5V AAA batteries 1, To install batteries: Open the cover of battery case, insert 4 X 1.5V AAA batteries, according to indicated polarity (batteries not included). Battery installation should be done under adult supervision only!

Do not mix old and new batteries. Do not mix different types of batteries. 1.Insert one side of the USB connector into the drone/battery, and the other side into any computer USB port. B a a i=}

=o How to get the battery he frame om One hand press the frame as picture shows, and another hand press the battery to get it out. Controller Camera light The light will flash while taking picture and remian on while recording video Power light Press one time to Unlock the drone press again for slowly landing P ands for emerge!

Speed Select own once to change Throttle /Left Stick-

Trim button Drone Replacing Damaged blades:

Your set will come with 4 replacement rotors, two (A) type and two (B) type. You will see the "A" and "B" word on the canopy, put the rotor on the motor accordingly. One key return function Headless mode Press once into he:

press again to quit he Take picture/record video for taking picture, Trim button Trim button mode 85 function ds for recording video Operating steps 3. Turn on the DRONE

(The LED light on the drone flashes rapidly) 1.Put the throttle lever down. 4. Place the DRONE ata level position. 6.After the DRONE connect to the controller, press this button for start flying, and press again if you want to stop the DRONE 5. Push the throttle lever up and down, a beep will sound. The controller connects to the DRONE

( The LED light on the drone remains on).The DRONE is ready to fly. Operation and Control Up and down Forward and Backward t Rise prep Left Spin and Right Spin Leftside and Rightside Left Spin Right Spin > Lettie 7 Rabie He, Note: When the drone is flying towards you, the control directions are reversed. 4 Forward/backward fine-tuning Leftside/rightside fine tuning f) G2)

= BS Backward Trimmer Backward Trim Forward Trim Forward Trimmer Leftside as as Trim j : 0 Ve y wy, a Lefside

< trimmer

Rightside Trim RightSide trimmer Left spin Trim Right spin Trim Right Spin trimmer Radical Flips & Rolls You can perform flips with your DRONE in any of the speed settings. Press down the rudder once(one beep sounds) then push the rudder in related direction. Left flip aT Right flip Gi Soe Press down the rudder once and then Press down the rudder once and then push the rudder to left push the rudder to right Forward flip Backward flip he aT Press down the rudder once and then push the rudder to backward Press down the rudder once and then push the rudder to forward Before you perform a Flip Trick, always make sure you have enough space both above and below your DRONE . Auto t func Press the throttle and rudder down to 45 degree circle (as above) for 10 second, you will see the light on the PC board of drone flashing rapidly, then pls let go the throttle and rudder, the light on the PC board remains on, the auto trim finishes. One key return function When the drone is taking off, the LED light on the drone stop flashing, at the moment, the drone sets its front side to be the front direction for one key return flying.If you want to reset the front direction, then you need to turn off the re drone and reset it again Press the button as picture shows for one key back home function, and then control right sticker (Rudder) to every direction to quit this function. Control the rudder to quit this function

-6- (every direction) Press this button Headless function HOW TO GET INTO/QUIT HEADLESS FUNCTION FLYING?

Press the button on controller(as picture shows) you will hear beep sounds then you get into compass mode flying.To quit from compass mode just press it again and you will hear beep sound disappears. HOW TO RECOGNIZE THE " FORWARD. SIDE UNDER HEADLESS FUNCTION?

When the drone is taking off, the LED light on the drone stop flashing, at the moment, the drone sets its front side to be the front direction for headless mode flying. If you want to reset the front direction, then you need to turn off the rc drone and reset it again.

Normal camera:

VGA camera(Resolution: 640*480) \720P camera (Resolution: 1280*720) HOW TO REVIEWING PHOTOS/VIDEOS Insert the TF card into rc drone Before reviewing photos and videos, please insert one end of DATA CABLE onto port of camera correctly,the other end onto computer,open my computer"and you will find related file from which you can view photos and videos you took. nA Wifi camera:

0.3m pixel WIFI camera (Vga/640*480) 1.SOFTWARE DOWNLOAD AND INSTALLATION APP (IOS) APK (Android/ Oversea) APK (Android Mainland China) 1). Connect the model to the power, the indicator on camera turns red. 2). Enter the setting menu of your mobile device and turn on WIFI. 3). Find a network WIFI called HELICUTE FPV ,click connection until connected. 4). Open the HELICUTE FPV" software, click the play icon into the control interface. And you will see the real time video. SPOEScoS oF oe Oo A MELICUTE FPV see Se 5 1.0m pixel WIFI camera (720P/1280*720) 4.SOFTWARE DOWNLOAD AND INSTALLATION APP (IOS) APK (Android/ Oversea) APK (Android! Mainland China) 2.USING INSTRUCTION 1). Connect the model to the power. 2). Enter the setting menu of your mobile device and turn on WIFI. 3). Find a network WIFI called HELICUTE 720P FPV click connection until connected. 4). Open the HELICUTE 720P FPV" software, click the play icon into the control interface.And you will see the real time video. 5). To save video, pls insert the TF card (optional) into wifi camera foie 720P FPV FCC compliance statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC ID : 2AKPPHLTH8162 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Label size: 3cm*5cm

Shantou Helicute Model Aircraft Industrial Co.,Ltd. We, Shantou Helicute Model Aircraft Industrial Co.,Ltd declare that this EUT (FCC ID:

2AKPPHLTH8162) doesnt have ad Hoc Mode function on US/Canada frequencies. In addition, the frequency selection feature is disabled by firmware for devices marketed to the US/ Canada. For DTS part of this device, only channels 1-11 will be used in North America. Country code selection is disabled. Should you have any questions or comments regarding this matter, Please have my best attention. Sincerely yours,

Shantou Helicute Model Aircraft Industrial Co.,Ltd TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding:

Confidentiality Request regarding application for FCC ID: 2AKPPHLTH8162 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Print Name: David Zhuang Title: General manager Signature:

On behalf of Company: Shantou Helicute Model Aircraft Industrial Co.,Ltd Telephone: 13825847125 E-mail: Sales5@lisantoys.com

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Shantou Helicute Model Aircraft Industrial Co.,Ltd Address Grantee Code FCC ID Jiangbei Road, Longtian, Guangyi Street, Chenghai District,Chenghai,Shantou City,Guangdong, China 2AKPP 2AKPPHLTH8162 Authorized Contact Name David Zhuang Contact Email Contact Phone Sales5@lisantoys.com 13825847125 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date:2021-10-18 Print Name: David Zhuang Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database General manager Applicant Declaration Rev:0.0

Shantou Helicute Model Aircraft Industrial Co.,Ltd TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AKPPHLTH8162 To whom it may concern:

Date: 2021-10-18 We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou Branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Shantou Helicute Model Aircraft Industrial Co.,Ltd This authorization is valid until further written notice from the applicant. Print Name: David Zhuang Title: General manager Signature:

On behalf of Company: Shantou Helicute Model Aircraft Industrial Co.,Ltd Telephone: 13825847125 E-mail: Sales5@lisantoys.com