FCC ID: 2A6TTYS31-1 Game Controller

Welcome Guide Wireless controller 14 15 20 21 Button Layout Specications 76 BBluetooth Reconnecting Turn O Press the Home button or the Capture button to reconnect your controllers back to the console, 4 LED indicators on the side will start to ash in a regular pattern as an indication of reconnecting. 1.Transmission Media: Bluetooth 2.1 2.Carrier Wave: 2.402-2.480GHz 3.Protocol: Bluetooth 2.1 4.LED: 8 LED Lights & 8 Multi-Color LED lights 5.Battery: One Lithium polymer battery3.7V 400/mAH 6.Battery life: 2-3 hours after fully charged 7.operating voltage: 3.7V-4.2V 8.charging voltage: 5V 9.Operating temperature: -10~50 10.storage temperature: -20~70 11.Dimensions (approx): 7*20*41mm 12.weight(approx): 149g Connection A.Conventional Connection 1.Attaching the controllers to the console will connect them automatically. 2.The Joy-Con controllers will remain paired when you detach them from the console, and you'll be able to use them wirelessly. Turbo Function Note: The T button on the left controller can only the assign the buttons that are on the left controller. Same goes for the T button on the right controller. Hold down the T button and then press the button that you have set for the 3rd time to turn o its turbo function. (Controller will vibrate.)

* Hold the T button for 5 seconds to cancel the Turbo function of all buttons. Turbo Speed Adjustment

* A total of 3 turbo speeds can be adjusted cyclically. Hold down the T button and press the button for Controller(L).

(Controller will vibrate.) Hold down the T button and press the + button for Controller(R).

(Controller will vibrate.) Buttons can be set Left controller L / ZL button and Control Pad (Up / Down/ Left/

Right). Right controller R / ZR button and A / B / X / Y button. Vibration Level Adjustment Press the T button and push the Joy-stick up or down to adjust the vibration level of each controller.

(Controller will vibrate when adjusting between each vibration level.)

[4]

Charging Instructions 1.When the controllers are in the USB charging state, LED lights will ash slowly, if connected to the console, the lights will stay on when it is fully charged; If not, the light will be o. 2.When the pairing indication conicts with the charging low power indicator, the pairing indicates a concern. Warning 1. Do not expose the controller to high temperature, high humidity or direct sunshine. 2. Do not allow liquid or small particles to enter the controller. 3. Do not put any heavy object on the controller. 4. Do not disassemble the controller. 5. Do not twist or pull the cable too strongly. 6. Do not throw, drop, or apply strong shock to the controller. Turbo Mode A: Hold down the T button and then press the button that you want to set for the 1st time to turn on the normal turbo function.

(Controller will vibrate.) B: Hold down the T button and then press the button that you want to set for the 2nd time to turn on the automatic turbo function. (Controller will vibrate.)

[3]

[2]

Driver Package We support downloading the driver package through a USB connection to the computer to x some problems that may be encountered in use. If the driver package does not work, please contact us by email (support@binbok.com). Driver package download website: www.binbok.com NoteNo need to download driver if it can be used normally, otherwise new problems may occur due to version conicts) Use Method 1.Turn o your controllers. 2.Press down and hold the Left(Right) stick then connect them to your computer and release. 3.Run the Driver package. 4.Click the Update Firmware on your computer. 9 10 11 5 12 S L S R 8 13 22 23 24 25 1. - button 3. Directional pad 5. Screenshot button 7. X button 9. Y button 11. Right stick 13.Turbo button 15. ZL button 17. Pairing button 19. Type-C interface 21. R button 23. Pairing button 25. Type-C interface 2. Left stick 4.Turbo button 6. +button 8. A button 10. B button 12. Home button 14. L button 16. SL button 18. SR button 20. ZR button 22. SR button 24. SL button

[1]

Gyro Calibration 1. First, press and hold the Pairing Button to turn o the controller. 2. For controller(L), press the L , UP and the Capture button together to enter the calibration mode. For controller(R), press the R , X and the Home button together to enter the calibration mode. 3. When entering the calibration mode, LED lights will ash alternately. Then align the controllers with the rails on either side of the console, and slide them down BUT DO NOT slide them to the bottom of the rail. (If you hear a click you need to press the release button and slide them up a little.) 4. Then press the - button for controller(L) and + button for the control(R) to start the calibrating. Controllers will be reconnected back to the console when calibration is over. 1 2 3 4 1 2 3 4 16 17 18 19 1 2 YS31-1

* There are 5 levels of Vibration100%75%50% 30%0%.

(Default level is 50%) LED Ring Setting A: Normal Mode Hold the T button and press the joystick once to turn the light into normal modethe light will keep on this colorand repeat this procedure to change color.Controller will vibrate when set successfully) 1-8 colors: 1.Red 2.Orange 3.Yellow 4.Green 5.Cyan 6.Blue 7.Purple 8.Rainbow Brightness Adjustment Press & hold the T button and joystick to change the brightness, then release the joystick to x the brightness. Controller will vibrate when set successfully) B: Breathing Light Mode Hold the T button and press the joystick twice to turn the light into breathing light mode, the following three modes will be cycled. Controller will vibrate when set successfully) Mode 1: 1-7 color auto cycling. Mode 2 Rainbow light. Mode 3: Light o. S L S R Reset Button Function When there are some unsolvable faults in the controller, you can try to press and hold the reset button on the back of the controller for more than 5 seconds. At this time, the controller is powered o and reset, and you need to reconnect according to the method of connecting the controller for the rst time.

[5]

[6]

[7]

[8]

Low Voltage Alarm 1. If the lithium battery voltage is lower than 3.45V0.1V, the current channel tight ashes quickly and indicate low voltage. 2. If the lithium battery voltage is lower than 3.35V0.1V, it will automatically sleep. Binbok Game

@BINBOKOcial Ocial Homepage : binbok.com Register on this web to activate aftersales. US: support@binbok.com EUR: support.eur@binbok.com Business Contact: contact@binbok.com This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be u sed in portable exposure condition without restriction

C5266091_X10_Ed.2 Shantou Luomanna Cosmetics Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date:

2022.03.22 Subject: Request for Confidentiality FCC ID: 2A6TTYS31-1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No NOTE 1 NOTE 1 No No Short-Term Confidentiality NOTE 2 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, 1/1 C5266091_X10_Ed.2 Signature:

Name: Ou Hongxin Title: boss 1/1

C5266091_X8_Ed.1 Letter of Authorization Shantou Luomanna Cosmetics Co., Ltd. Company: Shantou Luomanna Cosmetics Co., Ltd. Address: Chendian Industrial Zone, Chaonan District, Shantou City Product Name: Game Controller Model Number: YS31-1, HS03-1, HL19-1, HL19-2 FCC Identifier: 2A6TTYS31-1 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Ou Hongxin Date: 2022.03.22 Title: boss Signature of applicant:

1/1

Shantou Luomanna Cosmetics Co., Ltd. Model Difference Product description: Game Controller Model name: YS31-1, HS03-1, HL19-1, HL19-2 Trade Name: binbok FCC ID: 2A6TTYS31-1 All the model are the same circuit and RF module, only for model name. Regards Sincerely Clients signature:

Clients name / title : Ou Hongxin (boss) Contact information / address: Chendian Industrial Zone, Chaonan District, Shantou City