Desk Lamp User Manual Read this instruction manual thoroughly before using the appliance and save it for future reference and if necessary pass the instruction manual on to a third party. WARNING: When using electrical appliance, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury. 1) General Any visitor, especially children, shall be kept away from the work area. Check if the electrical specifications of this luminaire are compatible with your installation. WARNNG: The power supply must be deactivated prior to assembly, maintenance, exchanging the bulb or cleaning processes. Remove the fuse or switch the fuse to OFF and secure from reactivation. For indoor use only. 2) Electrical safety Warning: if the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard. 3TECHNICAL CHARACTERISTICS Model: PL-0175 PL-0168,PL-0174,PL-0169 ,22017-000,22018-000 Rated voltage 120V 60Hz Rated wattage Max.13W, LED 4W wireless module outputDC5V ,1A The above Class III luminaire shall be supplied by the following approved independent LED adapter with model number RSS1006-156130-W2-B Model: PL-0073A-QI PL-0074QI Rated voltage 120V 60Hz Rated wattage Max.13W, LED 5W wireless module outputDC5V ,1A The above Class III luminaire shall be supplied by the following approved independent LED adapter with model number RSS1006-156130-W2-B 4 Maintenance / Cleaning Disconnect from mains before maintenance or cleaning. Repairs should only be carried out by qualified persons and using genuine spare parts. Inappropriate repairing could cause significant danger. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced. WARNING: The use of any accessory not specified in this manual may present a risk of personal injury. 5ASSEMBLY INSTRUCTIONS Place lamp base on a stable, flat surface indoor. Insert the lead of the power adaptor to the DC input jack of lamp. Then connect the wall plug adapter to the electrical outlet. Use the 3 way touch switch on the base to adjust the brightness to meet your needs. Touch Switch with On/Off and three Step Dimming: Low, Medium and High. Move the gooseneck to position the light as desired. Use the wireless charging function to charge your Mobile device. For best results, please the mobile device (without case) on base to charge. WIRELESS CHARGE COMPATABILITY: All Qi wireless enabled devices. 6) FCC/IC RULES This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s). ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 10cm between the radiator&
your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrls.Installation et mise en uvre de ce matriel devrait avec changeur distance minimale entre 10 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec dautres. 7 Others (Service, Repairing, Guarantee, etc.) Have your product repaired by a qualified person. This electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts, otherwise This may result in considerable danger to the user. Please contact the store which you bought the product for after sale services if any.