SOUND PARTNER ENGLISH MODEL AN-SS2 OPERATION MANUAL Introduction Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. AN-SS2 consists of Sound Partner and Bluetooth Transmitter. Special Notes FCC Notice Suppliers Declaration Of Conformity SHARP SOUND PARTNER, MODEL AN-SS2 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must ac-
cept any interference received, including interference that may cause undesired operation. Responsible Party:
MIZARI ENTERPRISES, INC. 5455 WILSHIRE BOULEVARD, SUITE 1410, LOS ANGELES, CA 90036 TEL: 1-800-BE-SHARP NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. z Consult the dealer or an experienced radio/TV technician for help. Warning:
responsible for compliance could void the users authority to operate the equipment. Special Notes (continued) FCC RF Radiation Exposure Statement 1. This device must not be co-located or operating in conjunction with any other antenna or transmitter. For Bluetooth Transmitter:
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and persons body. For Speaker:
2. For body worn operation, this device has been tested and meets FCC RF exposure guidelines. When used with an accessory that contains metal may not ensure compliance with FCC RF exposure guidelines. IC Radiation Exposure Statement (For Users In Canada) This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. This device complies with Innovation, Science and Economic Development Canadas license-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Caution: Exposure to Radio Frequency Radiation:
1. To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. For Bluetooth Transmitter:
2. To comply with RSS 102 RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. For Speaker:
2. For body worn operation, this device has been tested and meets RF exposure guidelines when used with an accessory that contains no metal. Use of other accessories may not ensure compliance with RF exposure guidelines. Special Notes (continued) Canada, Industry Canada (IC) Statement Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003 et RSS-247. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. l'appareil ne doit pas produire de brouillage, et, and 2. l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Attention: exposition aux rayonnements radiofrquences:
1. Pour se conformer aux exigences de conformit RF canadienne l'exposition, cet appareil et son antenne ne doivent pas tre co-localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. Pour l'metteur Bluetooth:
2. Pour se conformer aux exigences de conformit CNR 102 RF exposition, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes. Pour le prsident:
2. Pour une utilisation sur le corps, cet appareil a t test et respecte les directives sur l'exposition aux RF lorsqu'il est utilis avec un accessoire sans mtal. L'utilisation d'autres accessoires peut ne pas garantir la conformit aux directives d'exposition aux RF. Additional Information 1. Radio frequency exposure Sound Partner AN-SS2 is a radio transmitter and receiver. When in operation it communicates with a Bluetooth equipped mobile device by receiving and transmitting to 2.48 GHz. This product is designed to operate in compliance with the RF exposure guidelines and limits set by national authorities and international health agencies when using compatible mobile phone. Special Notes (continued) 2. Battery information
- A rechargeable battery has a long service life if treated properly.
- A new battery or one that has not been used for a long period of time could have temperatures, never above 122F (50C) or below 14F (-10C).
- For maximum battery capacity, use the battery at room temperature.
- If the battery is used in low temperatures, the battery capacity will be reduced. The battery can only be charged in temperatures between 41F (5C) and 104F (40C).
- RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 3. Removal of waste batteries and accumulators
(Product with embedded battery ONLY)
- In case this product contains a battery incorporated within the product which cannot be remove the battery, either for replacement or for recycling at the end of this products working life. To prevent damage to the product, and for their own safety, users should not attempt to remove the battery and should contact authorized independent service providers for advice or call 1-800-BE-SHARP. CAUTION:
Internal lithium battery in the unit should not be replaced by end users due to danger of explosion if battery is incorrectly replaced and must be replaced with the exact type battery by authorized service providers. Recycling lithium-ion batteries Lithium-Ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you. For more information regarding recycling of rechargeable batteries, call toll free 1-800-822-8837, or visit http://www.call2recycle.org/
Caution: Do not handle damaged or leaking Lithium-Ion batteries. Special Notes (continued) Avoiding hearing damage If volume on the headset is too high, permanent hearing loss may occur. Please set the volume to a safe level. You can become habitual to hear at high volume that may sound speech, stop listening and have your ears checked by the specialist doctor. The louder the volume, the more quickly the hearing can be damaged. Hearing experts suggest how to protect your hearing Limit the amount of time you use the headset at high volume. Avoid the habit of increasing the volume so that you do not hear the loud noises around you. Turn the volume down if you cannot hear people speaking around you. For setting the maximum volume limit of the connection device, refer to the instruction manual supplied with the connection device. Class B equipment (home-use broadcasting communication equipment):
This equipment is intended for home-use (Class B) electromagnetic compatibility equipment and can be used in all areas. FOR YOUR RECORDS For your assistance in reporting this unit in case of loss or theft, please record below the model number and serial number which are located on the unit. Please retain this information. Model number Serial number Date of purchase Place of purchase
.............................. ............................. ............................. ............................. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other trademarks and trade names are those of their respective owners. Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies International, Ltd. registered in the United States and other countries. IMPORTANT SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/
installing, operating and cleaning the product. To ensure your safety and prolong the service life of this product, please read the following precautions carefully before use. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) 12) or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Additional Safety Information 15) Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For product intended to operate from battery power, or other sources, refer to the operating instructions. 16) Overloading - Do not overload wall outlets, extension cords, or integral convenience ck. IMPORTANT SAFETY INSTRUCTIONS (continued) 17) Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could 18) Damage Requiring Service - Unplug this product from the wall outlet and refer servicing n the apparatus. a. When the AC cord or plug is damaged, b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive e. If the product has been dropped or damaged in any way, and f. When the product exhibits a distinct change in performance - this indicates a need mal operation, for service. 19) Replacement Parts - When replacement parts are required, be sure the service shock, or other hazards. 20) Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 21) Wall or ceiling mounting - When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer. 22) Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 23) Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service same overload protection as the original plug. 24) Stand - Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturers instructions. Use only the mounting hardware recommended by the manufacturer. Accessories The following accessories are included. Bluetooth Transmitter x 1 Micro USB Charging Cable Micro USB Charging
(AN-WD3) x 1 (approx. 30 cm) Cable x 1
(approx. 1 m) Audio Cable x 1 Precautions General high place. the unit. zDo not drop the product from a zDo not place anything heavy on zDo not replace the battery, the unit may explode. zThis device is not a medical device. zIf you have a medical device implanted, contact your doctor before using this unit. zKeep the unit away from direct excessive dust, humidity and electronic / electrical equipment which generate electrical noise. to zDo not expose the unit higher to moisture, temperatures or to extremely low temperatures. zDo not repair or disassemble the unit. Refer internal service to your local SHARP service facility. z lighted candles, should be placed on the apparatus. zMake sure that an infant or a child does not swallow a small components of the product. zIf the unit is exposed to a large the amount of sweat, wipe product clean. zThe apparatus is designed for use in moderate climates. zAttention should be drawn to the environmental aspects of battery disposal. zThe ventilation impeded by covering should not be the ventilation openings with items, such as newspapers, tablecloths, curtains, etc. z do not expose this appliance to dripping or splashing. No object shall be placed on the apparatus. Controls and indicators Sound partner Speaker Microphone C L E A R V O I C E CLEAR VOICE Volume/Music Select Button Clear Voice Button Bluetooth Transmitter Bluetooth Button Power Button Power Indicator USB terminal for charge Play/Pause/Mode Button Optical/Audio Switch Pairing Button Audio In Optical In DC IN 9 Controls and indicators (continued) Bluetooth transmitter Indicator Power Indicator Sound partner indicator status Status Power Off Turns off. Power indicator (Blue/Purple/Red) Battery status When the power is turned on, the power indicator blinks three times according to the battery status. zBlue : approximately 70% charge zPurple : approximately 70% - 20% charge zRed : approximately 20% remaining During pairing Blinks in purple once in every seconds. Unconnected Connected Blinks in blue twice in about 5 seconds Blinks in blue once every 5 seconds Clear voice ON : blinks in purple once OFF : blinks in purple twice Charging Blinks once every seconds.(The power indicator color changes according to the remaining battery charge ) Fully charged Turns off. Bluetooth transmitter indicator status Status Connected Power indicator (Blue) Blinks once every 5 seconds Unconnected Blinks twice in about 5 seconds. No power source Turns off. During pairing Blinks once in every seconds. Successful pairing Lights up for about 3 seconds. Charging the Sound Partner Charging the battery micro USB charging cable. 1. Open the micro USB charging terminal cover and then connect the 2. Plug the other end of micro USB charging cable into a computer or USB AC adaptor (5V, 1A) that is powered on. Note: The sound partner does not operate while charging. To computer or USB AC adaptor
(commercially available) Charging Indication:
Power Indicator Blinks in red 20% remaining Battery status Blinks in purple Blinks in purple 20% - 70 %
approximately 70%
Cautions:
zFor safety of the built-in battery, the function to stop charging works depending on the ambient temperature. Charge the battery at room temperature 5 C or above. zAt extremely high or low temperatures, the battery may not be fully charged. every six months. batteries. zTo maintain functionality, the device needs to be charged at least once zBattery of the device has limited life, as with any other rechargeable zCapacity may gradually be decreased over time of which extent may vary depending on the conditions of use and external environment. zThere are multiple factors such as volume level, external environment etc that may affect the time of device power turning off, other than the percentage of battery left. zUse this product only with an agency approved power supply which meets local regulatory requirements. zThe equipment shall be connected only to a power supply with limited power source. Bluetooth transmitter connections to TVs Supplying power to the Bluetooth transmitter If you attach the included Bluetooth transmitter to your TV, you can enjoy the sound of the TV with your sound partner. zPower supply can be obtained from USB AC adaptor or TV/
monitor using micro USB charging cable. USB AC adaptor
(commercially available) Bluetooth transmitter connections Caution:
Turn off all other equipment before making any connections. Notes:
zRefer the operation manual of the equipment to be connected. zFully insert the plugs to avoid noises. Audio cable connection:
Optical cable connection:
OPTICAL AUDIO Audio cable Input selector switch to OPTICAL OPTICA L AUDIO Optical digital audio cable
(commercially available) zIf the TV/monitor does not have the optical output connect it to the headphone socket. zIf you want to hear sound from both the television speaker and the sound partner, see the instruction manual for the television.Some TVs may not be able to output audio from both. Connecting with Bluetooth transmitter (pairing) Pairing with Bluetooth transmitter 1. Connect the Bluetooth transmitter to a TV etc. Set the input select switch to the connected audio cable or optical cable. 2. Press and hold the PAIRING button on the Bluetooth transmitter for about 2 seconds. Bluetooth transmitter indicator blinks blue. OPTICAL AUDI O PAIRING Pairing Button 3. Press and hold the POWER button on the sound partner for about 2 seconds to turn it on. zWhen pairing is completed, you can hear the sound CONNECTED Bluetooth transmitter Indicator from sound partner. zIf you cannot pair automatically, please keep pressing the Bluetooth button of the sound partner for about 2 seconds. Notes:
zThe Bluetooth transmitter is only for the sound partner (AN-SS2 ). It cannot connect to other devices. zIf the connection between the supplied Bluetooth transmitter and the sound partner does not work well, press and hold the Bluetooth transmitter PAIRING button for about 10 seconds to reset, and try again. Indicator status:
Status During pairing Status indicator (Blue) Blinks once in every seconds. Successful pairing Lights up for about 3 seconds. Connected Blinks once every 5 seconds. Unconnected Blinks twice every 5 seconds. Listening to the TV sound 1. Connect the paired Bluetooth transmitter to the TV 2. Set the Bluetooth transmitters input selector switch to the connected 3. Turn on the TV and hold the POWER button on the sound partners for audio cable or optical cable. 2 seconds to turn it on. If the sound partner does not connect, make the connection again follow the procedure on page 11. Volume control button to increase the volume button to decrease the Press the and press the volume. When the volume level is set to maximum The volume does not change when press quickly and continuously. Volume / Song Selection Button LEAR VOICE Play / Pause / MODE Button Muting The volume is muted temporarily when pressing the Press again to restore the volume. button. Notes:
zWhen you are listening to audio by connecting an audio cable to the headphone socket, the sound of the TV may be lower even if you increase the volume of the sound partner unit, please increase the headphone volume on the TV. If you want to output audio from both the TV speakers and the sound partner, please refer to the TV instruction manual. If the product does not output audio from the TVs speaker with the audio cable connected, disconnect the audio cable from the headphone socket before listening to audio using the TVs speaker. zTwo sound partner units can be connected to one supplied Bluetooth transmitter. If you want to connect a second device, turn off the power of the first sound partner, and then hold the Bluetooth transmitter's PAIRING button for about 2 seconds to pair it. Turn on the second sound partner unit and hold the Bluetooth button for about 2 seconds. When the second pairing is complete, please power on the first sound partner. Listening to Bluetooth enabled devices Bluetooth Bluetooth wireless technology is a short-range radio technology that enables wireless communication between various types of digital devices, such as mobile phone or computer. It operates within a range of about 10 meters (30 feet) without the hassle of having to use cables to connect these devices. AN-SS2 supports the following:
Communication System: Bluetooth
(Advance Audio Distribution Profile), and AVRCP (Audio/Video Remote Qualcomm aptX audio Qualcomm aptX audio is a Bluetooth wireless technology that prevents loss of sound and provides CD-quality audio. You can enjoy clear audio sound when listening to music and watching movies. Qualcomm aptX audio works automatically only on the phones or the audio devices that support Qualcomm aptX audio. zQualcomm aptX and Qualcomm cVc are products of Qualcomm Technologies, Inc. and/or its subsidiaries. zQualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. zaptX and cVc are trademarks of Qualcomm Technologies International, Ltd., registered in the United States and other countries. Notes when using unit with a mobile phone z Please refer to the operating manual supplied with the mobile phone for details on operation of your mobile phone while transmitting the sound using a Bluetooth connection. Bluetooth data. This unit can memorise up to a maximum of 8 devices. Once paired, it is not necessary to pair them again unless:
z pairing is made with more than 8 devices. Pairing can only be made one device at a time. If subsequent device is paired, the oldest device paired will be deleted and replaced with the new one. Listening to Bluetooth enabled devices (continued) Pairing Bluetooth devices 1. Press the POWER button to turn on the sound partner. 2. Press and hold the Bluetooth button for about 2 seconds. The power indicator is turned on and blinks in blue. 3. Perform pairing procedure on the source device to detect this sound partner. AN-SS2 SHARP will appear in the detected devices list (if available) in the source device. (Refer the source device operating manual for details). 4. When pairing is completed the voice prompts AN-SS2 SHARP Notes:
z To pair with other device, repeat steps 1-4 for each device. During pairing mode the power indicator turns purple. z Due to the security feature of the Bluetooth device, some devices may not be able to be paired. z Make the Bluetooth connection again if the source device is not turned on, or its Bluetooth functionality is off or is in sleep mode. z Once a device is ousted or deleted from the pairing list, the pairing information for the device is also deleted. To listen to the sound from the device again, it needs to be re-paired. Perform steps 1-4 to pair the device again. z This sound partner can be paired to a maximum of 8 devices. If subsequent device is paired, the oldest device paired, will be deleted and replaced with the new one. Listening to Bluetooth enabled devices (continued) Listening to the sound Check that:
zThe source device Bluetooth functionality is ON. zPairing of this sound partner and the source device is completed. zThe transmission distance of the wireless signal between the device and the sound partner is about 10 meters (30 feet). 1. Press the POWER button to turn on the sound partner. During connecting the power indicator blinks in blue. 2. Sound partner is in connected mode. When connected the power blinking once every 5 seconds. indicator will 3. Press the button on the source device to VOICE start Bluetooth streaming playback. Play / Pause / MODE Button Function Operation Volume up Press the button. Volume down Press the button. Reverse Skip up Press and hold the button for about 2 seconds. Press and hold the button for about 2 seconds. Listening to Bluetooth enabled devices (continued) About playback operation Function Play/Pause or mute Operation Press the button. Volume up Press the button. Volume down Press the button. Reverse Skip Up CLEAR VOICE on/off Bluetooth Enable device Voice Control Switching a paired device Press and hold the button for about 2 seconds. Press and hold the button for about 2 seconds. Press the CLEAR VOICE button to switch to On/Off the function.
( It's a mode to listen to the voice of a person with a clear voice ) Press Bluetooth button. zYou can access voice controls on mobile devices to make calls, play music, ask for weather, check sports scores, etc. zThis function does not work when the mobile device is not compatible. Press and hold the Bluetooth and for about 5 seconds. Pairing will be canceled for 10 seconds, so please pair with the device you want to switch to in the meantime. zVoice Control supports looge Assistant / Siri. Other applications are not supported. Notes:
Some Bluetooth devices may not be able to perform the above operations, such as limited playback operations. Call functions You can receive a call through this sound partner when it is connected to a mobile device such as a smartphone via Bluetooth . About call operation Function Answer a call Press the button. Operation End a call Press and hold the button for about 2 seconds. Switch voice to smartphone Press and hold the zPress and hold the button for about 2 seconds. button for about 2 seconds again to switch the sound to sound partner. Mute a call Unmute a call Decline an incoming call Press and hold the button for about 2 seconds. Press and hold the button for about 2 seconds. Press and hold the button for about 2 seconds. Note:
Some mobile devices do not support the Call Function feature. Thus, this operation may not work. Disable or change language of voice prompts The sound partner performs voice prompts according to the operation. If you want to disable or change language of voice prompts, use the following procedure. Press and hold the CLEAR VOICE button and button simultaneously for about 5 seconds. Japanese English Chinese Off Troubleshooting Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorised SHARP dealer or service center. Symptom Possible cause No sound is heard. z The volume level set to minimum. z Are the connections made correctly. z Is the input selector switch properly switched?. z Is the volume of the source device set to 0. z Is the connected device powered on?. z Is the connected device properly connected to this unit?
z Is the pairing information for the device you want to use by pairing another Bluetooth device deleted? Please try pairing again. z Is it set to output audio from another Bluetooth device, such as when two units are connected simultaneously? Press and hold the z button for about 2 seconds to switch the device z Is the distance between this unit and the Bluetooth device too long?
z Is the Bluetooth setting of the connected device turned off?
The button did not work properly while pressing The power is not turned on z The audio cable may not be connected correctly. Sound is heard from one side only. Insert the cable plug all the way into the terminals of the Bluetooth transmitter and TV z Is the audio cable using a 3.5 mm / 3 pole type?
z Turn off the power of this unit and then turn it on again. z Charging may be low. Charge using the supplied or commercially available micro USB cable. z If the battery does not turn on after charging, or if it turns off immediately, the battery may be exhausted. z The unit is too near to a device that generates electromagnetic Poor sound quality z There is an obstacle between the unit and the Bluetooth stereo audio radiation. source device z Is the volume to high, please lower the volume. Power Off without notice z z Is the sound partner no sound If the temperature of the environment you are using is high, the power is turned off for safety. Please use within the operating temperature range. As part of our policy of continuous improvement, SHARP reserves the nominal values of production units. There may be some deviations from these values in individual unit. sound partner Music playback time Battery charge time Dimension Weight Terminal Bluetooth Frequency band Compatible Bluetooth Maximum communication range Supported content protection method Supported coded Approx. 16 hours (*1) Approx. 2 hours 30 minutes (*1) Width : 184mm, Depth: 185mm, Height: 18mm 88g Micro USB 2.402GHz - 2.480GHz Bluetooth 5.0 (HSP / HFP / A2DP / AVRCP) Line of sight approx. 10 m (30 ) SCMS-T Operating temperature
(*1) The time may vary depending on the ambient temperature and the SBC /AAC / Qualcomm aptX / Qualcomm aptX Low Latency 0C - 40C conditions used. Bluetooth transmitter Dimension Weight Terminal Bluetooth Frequency band Compatible Bluetooth Maximum communication range Supported coded Width: 60mm, Depth: 60mm, Height: 22mm 40g Micro USB, Optical digital input, Audio Input 2.402GHz - 2.480 GHz Bluetooth 5.0 (A2DP) Line of sight approx. 10 m (30 ) SBC / Qualcomm aptX / Qualcomm aptX Low Latency 0C - 40C Up to 2 sound partners per Bluetooth transmitter (*2) Operating temperature Number of simultaneous connections
(*2) Qualcomm aptX Low Latency is not supported when two units are connected simultaneously. Listening to Bluetooth enabled devices (continued) Notes:
zIf a device such as microwave oven, wireless LAN card, Bluetooth device or any other device that uses the same 2.4 GHz frequency is placed near the system, some sound interruption may be heard. zThe transmission distance of the wireless signal between the device and the unit is about 10 meters (33 feet), but may vary depending on your operating environment. zIf a steel concrete or metallic wall is between the device and the unit, the system may not operate at all, because the wireless signal cannot penetrate metal. zIf this unit or the source device is turned off before Bluetooth connection is completed, pairing will not be completed and the pairing information will not be memorised. Start pairing again. zTo pair with other devices, repeat steps 1 - 4 for each device. This unit can memorise up to a maximum of 8 devices. If subsequent device is paired, the oldest device paired will be deleted. zOnce a device is ousted or deleted from the pairing list, the pairing information for the device is also deleted. To listen to the sound from the device again, it needs to be re-paired. Perform steps 1 - 4 to pair the device again.