RUITZ0004MPZZ 26-Aug.-2016 Ver.0.3 Bluetooth low energy Module Bluetooth 4.2 low energy RUITZ0004MPZZ Data Report Please note that this manual should not be provided to end-users. SHARP CORPORATION 1/7 RUITZ0004MPZZ 26-Aug.-2016 Ver.0.3 Control No. HD-AG-A150049 (1/5) Control name General Items Scope This specification (Specification) applies to the hybrid IC RUITZ0004MPZZ, a Bluetooth 4.2 low energy module (Product). 1. Type: RUITZ0004MPZZ 2. Function:
Radio frequency module. Bluetooth standard Ver 4.2 low energy conformity 3. Application: Health & Fitness Equipment, Sensor, Toys 4. Note:
a. Regulatory information:
Compliance with each radio law and/or regulation in below listed countries has been confirmed under the conditions follows:
- Company name of Manufacturer: SHARP CORPORATION
- Equipment name/ Model name: Wireless Module / RUITZ0004MPZZ
- Manufacturing date: traceable from lot number shown on device
- Country of origin: JAPAN
- Countries: Canada, Japan, U.S.A. To maintain the compliance, please install RUITZ0004MPZZ into your final product within the scope of the specification and regulation of each country. Japan Regulatory Information This module is approved with the specific antenna on this module. a) Please ensure that your product can bear a label with the following information. If the product is so small that it is not practicable to place the label, please place it in the instruction manual and package. The mark diameter shall be equal or greater than 3mm. This product installs a radio system which has been approved as a radio station in a low power data communication system based on the Radio Law. RUITZ0004MPZZ : 001-A05676 SHARP CORPORATION 2/7 RUITZ0004MPZZ 26-Aug.-2016 Ver.0.3 Control No. HD-AG-A150049 (2/5) Control name General Items Canada Regulatory Information a) This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. L'utilisation de ce dispositif est autorise seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. b) This product is certified as type of the portable device with Industry Canada Rules. To maintain compliance with RF Exposure requirement,please use within specification of this product.
- IC: 548B-RUITZ0004MP Ce produit est certifi comme type de l'appareil portable avec Industrie Rgles de Canada. Pour maintenir l'acquiescement avec exigence Exposition de RF, veuillez utiliser dans spcification de ce produit.
- IC: 548B-RUITZ0004MP c) Please notify certified ID by either one of the following method on your product. Specifiez ID certifie dans votre produit par une de mthode suivante.
-Contains Transmitter module IC : 548B-RUITZ0004MP
-Contains IC : 548B-RUITZ0004MP Pecifiez ID certifie dans votre produit par une de mthode suivante.
-Contains Transmitter module IC : 548B-RUITZ0004MP
-Contains IC : 548B-RUITZ0004MP FCC Regulatory Information a) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. b) Please notify certified ID by either one of the following method on your product.
-Contains Transmitter Module FCC ID: APYBSC0001
-Contains FCC ID: APYBSC0001 c) CAUTION: changes or modifications not expressly approved by the party responsible for compliance could void the uses authority to operate the equipment. d) This product is certified as type of the portable device with FCC Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product.
- FCC ID: APYBSC0001 e) The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. SHARP CORPORATION 3/7 RUITZ0004MPZZ 26-Aug.-2016 Ver.0.3 Control No. HD-AM-A150049 (1/1) Control name Absolute maximum ratings Absolute maximum ratings Symbol VCC_NRF GND VIO Storage temperature MSL ESD HBM ESD MM Parameter Moisture Sensitivity Level Human Body Model Machine Model Min.
-0.3
-0.3
-40 3 Endurance Flash Memory Endurance 20000 Retention Number of times an address can be written between erase cycles Flash Memory Retention 10 years Max.
+3.6 0 VCC_NRF+ 0.3
+85 1 100 2 Units V V V Deg-C kV V write/erase cycles At 40 deg-C times SHARP CORPORATION 4/7 RUITZ0004MPZZ 26-Aug.-2016 Ver.0.3 Control No. HD-AE-A150049 (1/7) Control name Electrical characteristics Electrical characteristics Recommendation operating range Symbol VCC_NRF VCC_NRF Parameter Supply voltage, normal mode Supply voltage, normal mode, DC/DC converter output voltage 1.9 V tR_VCC_NRF Supply rise time (0V to 1.8V)*1 TA Operation temperature Min. 1.8 2.1
-25 Typ. 3.0 3.0 25 Max. 3.6 3.6 100 75 Units V V ms Deg-C
*1 The on-chip power-on reset circuitry may not function properly for rise times outside the specified interval. Also after power off, please start up from below 0.3V. RF Specifications Symbol Fop PLLres Df PRF PRFC PRFCR PWHISP PBW PRF1 PRF2 PRXMAX PSENS IT PSENS DT Description Operating frequencies PLL programming resolution Frequency deviation Maximum output power RF power control range RF power accuracy RF power whisper mode 20 dB bandwidth for modulated carrier 1st Adjacent Channel Transmit Power 1 MHz 2nd Adjacent Channel Transmit Power 2 MHz Maximum received signal strength at < 0.1% PER Receiver sensitivity (0.1% BER) Ideal transmitter Receiver sensitivity (0.1% BER) dirty transmitter Min. 2402 Typ. 1 Max. 2480
+/-225
+/-250
+/-275 20 4 24
-30 950 0
-93
-91
+/-4 1100
-20
-45 Units MHz MHz kHz dBm dB dB dBm kHz dBc dBc dBm dBm dBm SHARP CORPORATION 5/7 RUITZ0004MPZZ 26-Aug.-2016 Ver.0.3 Control No. HD-BA-A150049 (1/2) Control name Pin Layout Pin Descriptions Pin Pin name Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 GND P0.27 AIN1 XL1 P0.26 AIN0 XL2 function Ground Digital I/O Analog input Analog input Digital I/O Analog input Analog output Digital I/O P0.21 VCC_NRF Power Power AVDD Digital I/O P0.23 Digital I/O P0.17 GND Ground Power DEC2 Digital I/O P0.19 GND Ground Antenna In/Out OUT_ANT OUT_MOD RF In/Out GND Ground SWDIO Digital I/O Description Ground (0 V) General purpose I/O pin ADC input 1 Crystal connection for 32.768kHz crystal oscillator or external 32.768kHz crystal reference General purpose I/O pin ADC input 0 Crystal connection for 32.768kHz crystal oscillator General purpose I/O pin Power supply Analog Power supply General purpose I/O pin General purpose I/O pin Ground (0 V) Power supply for low voltage mode General purpose I/O pin Ground (0 V) Internal antenna. It should be connected to Pin 14 OUT_MOD for normal operation. RF I/O pin. It should be connected to Pin 13 OUT_ANT for normal operation. Ground (0 V) System reset (active low). Also HW debug and flash programming I/O SWDCLK Digital input HW debug and flash programming I/O P0.25 P0.03 AIN4 GND P0.01 AIN2 P0.02 AIN3 General purpose I/O pin General purpose I/O pin ADC input 4 Ground (0 V) General purpose I/O pin ADC input 2 General purpose I/O pin ADC input 3 Digital I/O Digital I/O Analog input Ground Digital I/O Analog input Digital I/O Analog input SHARP CORPORATION 6/7 RUITZ0004MPZZ 26-Aug.-2016 Ver.0.3 Control No. HD-BA-A150049 (2/2) Control name Pin Layout Pin 23 24 25 26 27 28 Pin name Pin function Digital I/O Analog input Power Digital I/O Analog input Digital I/O Analog input Analog input Digital I/O Analog input Ground Description General purpose I/O pin ADC Reference voltage DC/DC output General purpose I/O pin ADC input 6 General purpose I/O pin ADC input 7 ADC Reference voltage General purpose I/O pin ADC input 5 Ground (0 V) P0.00 AREF0 DCC P0.05 AIN6 P0.06 AIN7 AREF1 P0.04 AIN5 GND SHARP CORPORATION 7/7