All brand names shown are trademarks of their respective owners. Tous les noms de marque illustrs sont des marques de commerce de leurs propritaires respectifs. Todas las marcas que aparecen aqu son marcas registradas de sus respectivos dueos. MADE IN CHINA/FABRIQU EN CHINE/HECHO EN CHINA DISTRIBUTED BY JASCO PRODUCTS COMPANY LLC, 10 E. MEMORIAL RD., OKLAHOMA CITY, OK 73114. JASCO 2020 | 52252 | ZW3012 | 08/17/20 v1 Direct Wire, 40A Outdoor Smart Switch Portable Smart Multi Sensor In-Wall Smart Outlet Plug-in Switch Tamper-Resistant Outdoor Smart FCC/IC En This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate the device. Fr Cet appareil est conforme au paragraphe15 des normes FCC et au CNR pour les appareils exempts de licence dIndustrie Canada. Son utilisation est sujette aux deux conditions suivantes: (1) cet appareil ne doit pas occasionner de brouillage prjudiciable et (2) cet appareil doit accepter toutes les interfrences reues, notamment les interfrences qui peuvent provoquer un fonctionnement non dsir. NOTE DE LA FCC: Le fabricant nest pas responsable des interfrences sur les frquences radiolectriques ou tlvisuelles pouvant tre causes par des modifications non autorises de ce matriel. De telles modifications peuvent annuler le droit de lutilisateur utiliser cet appareil. REMARQUE: Cet appareil a t test et certifi conforme aux limites relatives aux appareils numriques de catgorie B dfinies dans le paragraphe15 des normes FCC. Ces limites ont t dfinies afin de fournir une protection raisonnable contre le brouillage prjudiciable en milieu rsidentiel. Cet appareil produit, utilise et peut mettre des ondes de frquence radio et, sil nest pas install et utilis conformment aux instructions, il peut provoquer un brouillage prjudiciable aux communications radio. Il nexiste toutefois aucune garantie que des interfrences ne se produiront pas au sein dune installation donne. Si cet appareil occasionne un brouillage prjudiciable la rception radiophonique ou tlvisuelle, il suffit dallumer et dteindre lappareil pour dterminer sa responsabilit. Nous encourageons lutilisateur essayer de corriger ces interfrences en appliquant une ou plusieurs des mesures suivantes:
Rorienter ou dplacer lantenne de rception. Augmenter la distance entre lappareil et le rcepteur. Brancher lappareil une prise secteur diffrente de celle du rcepteur. Consulter le revendeur ou un technicien spcialis en postes radio ou tlviseurs. Remarque importante: Pour se conformer aux exigences de conformit de la FCC concernant lexposition aux RF, aucune modification apporte lantenne ou au dispositif nest autorise. Toute modification apporte lantenne ou au dispositif pourrait faire en sorte que le dispositif dpasse les exigences dexposition aux RF et pourrait annuler le droit de lutilisateur utiliser ce dispositif. Es Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con las especificaciones de las normas radioelctricas (RSS) del Ministerio de Industria de Canad aplicables a aparatos exentos de licencia. El funcionamiento est sujeto a las siguientes dos condiciones: (1) este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo debe aceptar toda interferencia que reciba, incluso la que pudiera causar un funcionamiento no deseado. NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas modificaciones podran anular la autoridad del usuario para utilizar el equipo. NOTA: Este equipo ha sido probado y cumple con los lmites para aparatos digitales de Clase B, de conformidad con el apartado 15 de las normas de la FCC. Estos lmites estn diseados para proveer proteccin razonable contra interferencias perjudiciales en una instalacin residencial. Este equipo genera, usa y puede irradiar energa de radiofrecuencias y, si no se instala y usa segn las instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No obstante, no hay garantas de que no ocurrir interferencia en una instalacin en particular. Si este equipo provoca interferencia perjudicial a la recepcin de radio o televisin, lo que puede determinarse encendiendo y apagando el equipo, se recomienda que el usuario intente corregir la interferencia por medio de la implementacin de una o ms de las siguientes medidas:
Reorientar o reubicar la antena receptora. Incrementar la separacin entre el equipo y el receptor. Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que est conectado el receptor. Consultar al distribuidor o a un tcnico con experiencia en radio/televisin para Nota importante: Para cumplir con los requisitos de cumplimiento de exposicin de radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier cambio a la antena o dispositivo podra hacer que el dispositivo supere los requerimientos de exposicin de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo. solicitar asistencia. Responsible Party - US Contact Information | Parte responsable - Informacin de contacto de los Estados Unidos | Partie responsable - Coordonnes des tats-Unis FCC U2ZZW3012 | IC: 6924A-ZW3012 Jasco Products Company | Model: ZW3012/52252 10 E. Memorial Rd., Oklahoma City, OK 73114 | 1-800-654-8483 CAN ICES-3(B)/NMB-3(B) 1. Tools you will need IMPORTANT!
Confirm bulb is dimmable and in working order, switch is not functional without complete circuit. Getting to know your new Z-Wave device No neutral wire required Turn ON/OFF and adjust dim levels manually or remotely via the Z-Wave controller May be used in single-pole installation or with up to four Enbrighten add-on switches in 3-way or 4-way wiring configurations Compatible with all incandescent and most dimmable CFL/LED bulbs Uses a standard, rocker-style wallplate for single-gang installations Interchangeable paddle switch white & light almond paddle in package
(wallplate not included) Blue LED indicates dimmer location in a dark room Z-Wave certified for simple pairing and integrated home automation Screw terminal installation requires wiring connections for line (hot), load, and ground. Traveler wire required for 3-way or 4-way installation This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config 2. B C A D E F A. Ground (Green/Bare) B. Line or Load (Black) C. Line or Load (Black) D. Traveler (Red/Other) E. Top rocker press & release to turn dimmer ON, press &
hold increases brightness F. Bottom rocker press
& release to turn dimmer OFF, press & hold to dim STOP DO NOT RETURN THIS PRODUCT TO THE STORE NE RETOURNEZ PAS CE PRODUIT AU MAGASIN NO DEVUELVA ESTE PRODUCTO A LA TIENDA If you have any problems or questions, contact our U.S.-based Consumer Care at 1-800-654-8483, option 1, MondayFriday, 7AM8PM Central Time. For the most up-to-date product support, accessories, electronic (PDF) format manuals and more, visit www.byjasco.com/support. No user-serviceable parts in this unit. Si vous avez des problmes ou des questions, veuillez communiquer avec notre service la clientle aux tats-Unis au 1-800-654-8483, option1, du lundi au vendredi, de 7h 20h heure du Centre. Pour un soutien technique davant-garde, les nouveaux accessoires, les plus rcents manuels en format lectronique (PDF) et plus encore, visitez le site www.byjasco.com/support. Aucune des pices de ce dispositif ne peut tre rpare par lutilisateur. Si tiene problemas o dudas, comunquese con nuestro Centro de atencin al cliente con sede en EE. UU. al 1-800-654-8483, opcin 1, de lunes a viernes, de 7 a.m. a 8 p.m., hora del Centro. Para recibir el soporte tcnico ms actualizado sobre productos, accesorios, manuales en formato digital (PDF), entre otros, visite www.byjasco.com/support Esta unidad no contiene piezas que el usuario pueda reparar. WARNING RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS CONTROLLING APPLIANCES CAUTION:
TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE, MOTOR-OPERATED APPLIANCE, FLUORESCENT LIGHTING FIXTURE OR TRANSFORMER-SUPPLIED APPLIANCE. ONLY USE TO CONTROL INCANDESCENT OR DIMMABLE CFL/LED BULBS DO NOT EXCEED RATINGS DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.) DO NOT USE TO CONTROL RECEPTACLES FOR INDOOR USE ONLY AVERTISSEMENT RISQUE DINCENDIE RISQUE DE CHOC LECTRIQUE RISQUE DE BRLURES COMMANDE DES APPAREILS ATTENTION:
POUR RDUIRE LE RISQUE DE SURCHAUFFE ET DE DOMMAGES POSSIBLES DAUTRES APPAREILS, NE PAS INSTALLER POUR COMMANDER UN RCEPTEUR, UN APPAREIL ACTIONN PAR MOTEUR, UN APPAREIL DCLAIRAGE FLUORESCENT OU UN APPAREIL ALIMENT PAR UN TRANSFORMATEUR. UTILISER SEULEMENT POUR COMMANDER LES AMPOULES DEL ET FLUOCOMPACTES INCANDESCENCE OU INTENSIT RGLABLE NE PAS DPASSER LES CARACTRISTIQUES NOMINALES NE PAS UTILISER POUR COMMANDER DES APPAREILS POUR LESQUELS UN FONCTIONNEMENT IMPRVU POURRAIT ENTRANER DES CONDITIONS DANGEREUSES
(LAMPE RAYONS INFRAROUGES, LAMPE SOLAIRE, ETC.) NE PAS UTILISER POUR COMMANDER LES PRISES DE COURANT POUR UTILISATION INTRIEURE UNIQUEMENT ADVERTENCIA RIESGO DE INCENDIO RIESGO DE DESCARGA ELCTRICA RIESGO DE QUEMADURAS CONTROL DE EQUIPOS ELECTRODOMSTICOS PRECAUCIN:
A FIN DE DISMINUIR EL RIESGO DE RECALENTAMIENTO Y DE POSIBLES DAOS EN LOS DEMS EQUIPOS, NO INSTALAR PARA CONTROLAR UN RECEPTOR, UN APARATOS QUE FUNCIONAN A MOTOR, ARTEFACTOS DE ILUMINACIN DE LUZ FLUORESCENTE O APARATOS ALIMENTADOS CON TRANSFORMADORES. USAR EXCLUSIVAMENTE PARA CONTROLAR BOMBILLAS CFL/LED INCANDESCENTES O ATENUABLES NO SUPERE LOS VALORES NOMINALES ELCTRICOS NO USAR PARA CONTROLAR DISPOSITIVOS EN LOS QUE EL FUNCIONAMIENTO NO INTENCIONADO PODRA PROVOCAR SITUACIONES PELIGROSAS
(LMPARAS DE CALEFACCIN, LMPARAS SOLARES, ETC.) NO UTILICE PARA CONTROLAR TOMACORRIENTES. USE SOLAMENTE EN INTERIORES NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT. NE PAS UTILISER AVEC UN QUIPEMENT MDICAL OU DE SURVIE LES DISPOSITIFS COMPATIBLES AVEC LA TECHNOLOGIE Z-WAVE NE DEVRAIENT JAMAIS TRE UTILISS POUR ALIMENTER OU COMMANDER LA MISE EN MARCHE OU LARRT DE LQUIPEMENT MDICAL OU DE SURVIE. SE PROHBE SU EMPLEO EN EQUIPO MDICO O EQUIPO PARA EL MANTENIMIENTO DE LAS FUNCIONES VITALES LOS DISPOSITIVOS Z-WAVE NUNCA SE DEBEN USAR PARA SUMINISTRAR ENERGA ELCTRICA AL EQUIPO MDICO O AL EQUIPO PARA EL MANTENIMIENTO DE FUNCIONES VITALES, NI PARA CONTROLAR EL ESTADO DE ENCENDIDO O APAGADO DE DICHOS EQUIPOS. MANUAL MANUEL MANUAL 52252 ZW3012 READ IT OR WATCH IT Read instructions or watch easy-to-follow video. Scan QR code or visit goo.gl/22xkHv In-Wall No-Neutral Smart Dimmer Gradateur intelligent sans neutre mural Atenuador de luz inteligente para pared sin neutro Convert any smart control* to a multi-location switch
*For a list of compatible devices, visit ezzwave.com Smart Control Add-on Switches To purchase an add-on switch or for more details, visit ezaddonswitch.com. Multiple Paddle Colors Available ezzwave.com/paddlecolors Purchase additional items at ezzwave.com or visit your local retailer. In-Wall Smart Dimmers Plug-in Smart Dimmers In-Wall Add-on Switches In-Wall Motion Switch or Dimmer Plug-in Smart Switches In-Wall Smart Switches Enbrighten Smart LED Bulb In-Wall Hinge Pin Smart Fan Control Smart Door Sensor WARRANTY Jasco Products Company warrants this product to be free from manufacturing defects five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM 8PM, M-F, Central Time or www.byjasco.com if the unit should prove defective within the warranty period. GARANTIE Jasco Products Company garantit que ce produit est exempt de tout dfaut de fabrication pour une priode de cinq ans compter de la date de l'achat original par l'acheteur. Cette garantie se limite exclusivement la rparation ou au remplacement de ce produit et n'est pas applicable aux dommages indirects ou accessoires survenus sur d'autres produits utiliss avec ce produit. Cette garantie se substitue toute autre garantie expresse ou implicite. Certains tats ne permettent pas de restrictions quant la dure d'une garantie implicite ou permettent l'exclusion ou la limitation des dommages indirects et accessoires; il se peut, par consquent, que cette garantie ne s'applique pas dans votre cas. Cette garantie vous confre des droits juridiques prcis; vous pouvez jouir d'autres droits qui peuvent varier d'un tat l'autre. Veuillez communiquer avec notre service la clientle aux tats-Unis au 1-800-654-8483 (option 1) entre 7 h et 20 h, heure du Centre ou par lintermdiaire de notre site web www.byjasco.com si lappareil savre dfaillant au cours de la priode de garantie. GARANTA Jasco Products Company garantiza que este producto no tendr defectos de fabricacin durante cinco aos a partir de la fecha de compra del consumidor original. Esta garanta se limita a la reparacin o reposicin de este producto y no cubre daos indirectos o incidentales a otros productos que se pudieran utilizar con este producto. Esta garanta reemplaza cualquier otra garanta explcita o implcita. Algunos estados no permiten la aplicacin de limitaciones respecto de la duracin de una garanta implcita o permiten la exclusin o limitacin de la clusula sobre daos indirectos o incidentales, por este motivo las limitaciones arriba mencionadas pueden no aplicarse en su caso. Esta garanta le otorga derechos especficos y es posible que tenga otros derechos que pueden variar segn el estado en el que vive. Por favor, comunquese con nuestro Centro de atencin al cliente con sede en EE. UU. al 1-800-654-8483 (opcin 1) entre 7 y 20 h, Hora del Centro, o a travs de nuestro sitio de internet www.byjasco.com. Jasco Products Company LLC, Building B 10 E. Memorial Rd. Oklahoma City, OK 73114. SPECIFICATIONS ZW3012 Power: 120VAC, 60Hz Signal (frequency): 908.4/916MHz Maximum loads: 1-gang 600W, 2-gang 500W or 3-gang 400W incandescent, 300W CFL/LED Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module Operating temperature range: 32-104 F (0-40 C) Type 1 enclosure, independetly mounted (vertical position only), operating control:
type 1.c action, pollution degree (2), impulse voltage (2500V), software class A For indoor use only Specifications subject to change without notice due to continuing product improvement Requires minimum load requirement of 2W SPCIFICATIONS ZW3012 Tension : 120VCA, 60Hz Signal (frquence) : 908.4/916MHz Charges maximales : 1 compartiments 600W, 2 compartiments 500W, 3 compartiments 400W lampes incandescent 300W CFL/LED Porte : Distance vue entre la tlcommande et le module de rception Z-Wave le plus proche allant jusqu 150 pi (45.7m) Plage de tempratures de fonctionnement : De 32 104 F (de 0 40 C) Botier de type 1, mont indpendamment (position verticale seulement), intervention de type 1.c commande de fonctionnement, degr de pollution (2), tension de choc de
(2500V), logiciel de classe A Utilisation intrieure uniquement En raison damliorations continues du produit, les spcifications peuvent faire lobjet de changements sans pravis Ncessite une charge minimale de 2 W ESPECIFICACIONES ZW3012 Alimentacin: 120VCA, 60Hz Seal (frecuencia): 908.4/916MHz Cargas mximas: Caja para 1 conexiones 600W, caja para 2 conexiones 500W, caja para 3 conexiones 400W slo las lmparas incandescente 300W CFL/LED Alcance: Hasta 150 pies (45.7m) en lnea de visin directa entre el control remoto inalmbrico y el mdulo receptor Z-Wave ms cercano Rango de temperatura de funcionamiento: 32-104 F (0-40 C) Recinto de tipo 1, independientemente montado (solo en posicin vertical), control de operacin: accin tipo 1.c, grado de contaminacin (2), voltaje de impulso (2500V), software de clase A Para uso en espacios interiores solamente Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto Requiere un requisito de carga mnima de 2W 3.3. OROR Insert wires into holes, do not wrap wires around screws. Do not remove screws. Out to Light (Load) B A C D B A C D WARNING SHOCK HAZARD Turn OFF the power to the branch circuit for the dimmer and lighting fixture at the service panel. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the dimmer. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation, consult a qualified electrician. Multi-switch wiring For 3-way installations, please refer to add-on switch (46199) manual. Single-switch wiring Before installation, you may wish to change the paddle color to match your wallplate or dcor. Please proceed to section 5. 1. Shut off power to the circuit at circuit breaker or fuse box. IMPORTANT! Verify power is OFF to switch box before continuing. 2. Remove wallplate. 3. Remove the switch mounting screws. 4. Carefully remove the switch from the switch box. DO NOT disconnect the wires. 5. There are up to four screw terminals on the switch; these are marked:
A. GROUND Green/Bare B. LINE OR LOAD Black (connected to power or lighting) C. LINE OR LOAD Black (connected to power or lighting) D. TRAVELER Red/Other (only in 3-way installations) Match these screw terminals to the wires connected to the existing switch. 6. Disconnect the wires from the existing switch. Label wires according to the previous terminal Observe important wiring information IMPORTANT! This dimmer is rated for and intended to only be used with copper wire. Wire gauge requirements Use 14AWG or larger wires suitable for at least 80 C for supplying line (hot), load, ground and traveler connections. Wire strip length For attachment using the enclosures holes, strip insulation 5/8in. (16mm). UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in). 1. Connect the green or bare copper ground wire to the GROUND terminal. 2. Connect the black wire from the light to either LINE/LOAD terminal. 3. Connect the black wire from the electrical service panel (hot) to the other LINE/LOAD terminal. NOTE: The traveler terminal is only used for 3-way or 4-way wiring and should not be used if the dimmer is being installed in a 2-way system (one switch & one load). 4. Insert dimmer into the switch box being careful not to pinch or crush wires. 5. Dimmer must be independently mounted (vertical position only). 6. Secure the dimmer to the box using the supplied screws. 7. Mount the wallplate. 8. Reapply power to the circuit at fuse box or circuit breaker and test the system. Basic operation The connected light can be turned ON/OFF and adjust dim levels in two ways:
1. Manually from the front panel of the dimmer. 2. Remotely with a Z-Wave controller. Manual control The front panel rocker dimmer allows the user to:
Turn ON/OFF the connected fixture. 1. To turn the connected fixture ON, press and release the top of the rocker. 2. To turn the connected fixture OFF, press and release the bottom of the rocker. connection. 4. 5. Adding your device to a Z-Wave network 1. Follow the instructions for your Z-Wave certified controller to add To remove and reset the device 1. Follow the instructions for your Z-Wave certified controller to a device to the Z-Wave network. remove a device from the Z-Wave network. 2. Once the controller is ready to add your device, press and release 2. Once the controller is ready to remove your device, press and the top or bottom of the smart dimmer (rocker). release the top or bottom of the smart dimmer (rocker). You have complete control to turn your fixture ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller. If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit pin code. Figure 1:
To return your switch to factory defaults 1. Quickly press ON (top) button three times, then immediately press the OFF (bottom) button three times. The LED will flash ON/OFF five times when completed successfully. NOTE: This should only be used if your networks primary controller is missing or otherwise inoperable. NOTE: SmartStart enabled products can be added into a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity. Z-WAVE INTEROPERABILITY This product can be added and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. From Breaker Box Adjust dim levels 1. To increase brightness, press and hold the top of the rocker. 2. To decrease brightness, press and hold the bottom of the rocker. Cycle LED light The LED below the dimmer acts as a guide light or status indicator. How to cycle through options: Press up three times and down once quickly. 1. LED is ON when the load is OFF (guide light in the dark) (default) 2. LED is ON when the load is ON (indicates the dimmer is ON) 3. LED is always OFF 4. LED is always ON (illuminates dimmer in the dark) LED bulb adjustments Not all LED bulbs are made the same, and performance varies between dimmer brands. This can cause adverse bulb behavior, such as flickering or strobing. To account for this scenario, this dimmer features adjustable dim and brightness thresholds to allow setting minimum and maximum levels. Minimum dim threshold 1. Press OFF button four times, then ON button once quickly. 2. Light starts at the most recent dim level (default 1%). 3. Press the top or bottom rocker button until the bulb reaches desired brightness without 4. The LED stops flashing 10 seconds after releasing the button to indicate the minimum threshold flickering. is set. Note: This can be set by Z-Wave configuration parameter 30/size: 1 byte/values 1-99 (default 1) Maximum brightness threshold 1. Press ON button four times, then OFF button once quickly. 2. Light starts at the most recent brightness (default 99%) 3. Press the top or bottom rocker button until the bulb reaches desired brightness without 4. The LED stops flashing 10 seconds after releasing the button to indicate the maximum flickering. threshold is set. NOTE: This can be set by Z-Wave configuration parameter 31/size: 1byte/values 1-99 (default 99) 2. 1. Changing paddle color This step is optional. Before installation, you may want to change the color of the paddle to match your wallplate or dcor. 1. Lift the air gap tab at the base of the paddle. 2. Push side tabs in on one side and then the other to release paddle. Lift the cover up and off. 3. Simply put the new paddle onto the dimmer by inserting the air gap and side tabs and snapping securely into place. Once this step has been completed, return to section 3. The Enbrighten add-on switch is required for multi-switch 3-way or 4-way installations. Connecting the traveler terminal of this dimmer to a standard, non-Enbrighten switch will cause damage or result in improper function. If this dimmer is a part of a 3-way or 4-way multi-switch installation, do not connect the traveler wire or apply power until Enbrighten add-on switches are correctly installed. For more information on 3-way or 4-way installations, view the manual or quick-start guide for the Enbrighten add-on switch. This device supports Association Command Class (3 Groups) Association Group 1 supports Lifeline, Multi-level Switch report Association Group 2 supports Basic Set and is controlled with the local load Association Group 3 supports Basic Set and is controlled by double pressing the ON/OFF button Each Association Group supports 5 total nodes NOTE: Actual performance of any CFL or LED will vary from bulb type to bulb type and among manufacturers. It is important to note only bulbs designed as dimmable should be used on a dimmer. To find out if your bulb is dimmable, please check the package, the bulb itself or call the bulb manufacturer directly. For a complete list of recommended CFL/LED bulbs for this and other Z-Wave products from Jasco, please vist www.ezzwave.com.