MANUAL MANUEL MANUAL FCC / IC En This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unautho-
rized modifications to this equipment. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate the device. Fr Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils exempts de licence dIndustrie Canada. Son utilisation est sujette aux deux conditions suivantes :
1) cet appareil ne doit pas occasionner de brouillage prjudiciable; et 2) cet appareil doit accepter toutes les interfrences reues, notamment les interfrences qui peuvent provoquer un fonctionnement non dsir. NOTE DE LA FCC : Le fabricant nest pas responsable des interfrences sur les frquences radiolectriques ou tlvisuelles pouvant tre causes par des modifications non autorises de ce matriel. De telles modifications peuvent annuler le droit de lutilisateur utiliser cet appareil. REMARQUE : Cet appareil a t test et certifi conforme aux limites relatives aux appareils numriques de catgorie B dfinies dans le paragraphe 15 des normes FCC. Ces limites ont t dfinies afin de fournir une protection raisonnable contre le brouillage prjudiciable en milieu rsidentiel. Cet appareil produit, utilise et peut mettre des ondes de frquence radio et, sil nest pas install et utilis conformment aux instructions, il peut provoquer un brouillage prjudiciable aux communications radio. Il nexiste toutefois aucune garantie que des interfrences ne se produiront pas au sein dune installation donne. Si cet appareil occasionne un brouillage prjudiciable la rception radiophonique ou tlvisuelle, il suffit dallumer et dteindre lappareil pour dterminer sa responsabilit. Nous encourageons lutilisateur essayer de corriger ces interfrences en appliquant une ou plusieurs des mesures suivantes :
Rorienter ou dplacer lantenne de rception. Augmenter la distance entre lappareil et le rcepteur. Brancher lappareil une prise secteur diffrente de celle du rcepteur. Consulter le revendeur ou un technicien spcialis en postes radio ou tlviseurs. Remarque importante : Pour se conformer aux exigences de conformit de la FCC concernant lexposition aux RF, aucune modification apporte lantenne ou au dispositif nest autorise. Toute modification apporte lantenne ou au dispositif pourrait faire en sorte que le dispositif dpasse les exigences dexposition aux RF et pourrait annuler le droit de lutilisateur utiliser ce dispositif. Es Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con las especificaciones de las normas radioelctricas (RSS) del Ministerio de Industria de Canad aplicables a aparatos exentos de licencia. El funcionamiento est sujeto a las dos condiciones siguientes:
(1) este dispositivo no causa interferencia negativa y (2) este dispositivo debe aceptar las interferencias recibidas, incluidas las interferencias que puedan causar un funcionamiento no deseado. NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas modificaciones podran anular la autoridad del usuario para utilizar el equipo. NOTA: Este equipo ha sido probado y cumple con los lmites para aparatos digitales de Clase B, de conformidad con el apartado 15 de las normas de la FCC. Estos lmites estn diseados para proveer proteccin razonable contra interferencias perjudiciales en una instalacin residencial. Este equipo genera, usa y puede irradiar energa de radiofrecuencias y, si no se instala y usa segn las instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No obstante, no hay garantas de que no ocurrir interferencia en una instalacin en particular. Si este equipo provoca interferencia perjudicial a la recepcin de radio o televisin, lo que puede determinarse encendiendo y apagando el equipo, se recomienda que el usuario intente corregir la interferencia por medio de la implementacin de una o ms de las siguientes medidas:
Reorientar o reubicar la antena receptora. Incrementar la separacin entre el equipo y el receptor. Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que est conectado el receptor. Consultar al distribuidor o a un tcnico con experiencia en radio/televisin para solicitar asistencia. Nota importante: Para cumplir con los requisitos de cumplimiento de exposicin de radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier cambio a la antena o dispositivo podra hacer que el dispositivo supere los requerimientos de exposicin de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo. ID: U2ZZW4003A IC: 6924A-ZW4003A FCC U2ZZW4003 | IC: 6924A-ZW4003 Jasco Products Company | Model: ZW4003 / 14319, 14320 CAN ICES-3(B) / NMB-3(B) All brand names shown are trademarks of their respective owners. Tous les noms de marque illustrs sont des marques de commerce de leurs propritaires respectifs. Todas las marcas que aparecen aqu son marcas registradas de sus respectivos dueos. MADE IN CHINA/FABRIQU EN CHINE/HECHO EN CHINA DISTRIBUTED BY JASCO PRODUCTS COMPANY LLC, 10 E. MEMORIAL RD., OKLAHOMA CITY, OK 73114. JASCO 2015 | 14319, 14320 | ZW4003 | rev. 03/26/15 1. Tools You Will Need IMPORTANT!
The fixture controlled by the Z-Wave In-wall Smart Switch must not exceed 960 watts (Incandescent). The switch is designed only for use with permanently installed fixtures. Getting To Know Your New Z-Wave Device Turn ON/OFF manually or remotely via the Z-Wave controller Can be Included in multiple Groups and Scenes May be used in single pole installation or with up to two Jasco Add-on switches in 3-way or 4-way wiring configurations Compatible with all incandescent and CFL/LED bulbs Uses a standard, toggle wall plate for single gang installations (wall plate not included) Z-Wave Certified for simple pairing and integrated home automation Screw Terminal Installation requires wiring connections for Line (Hot), Load, Neutral, and Ground. Traveler wire required for 3-way or 4-way installation ThisZ-Wavedevicehasadvancedfeaturesthatallowyoutocustomizeyourexperience. ThesefeaturescanonlybeadjustedbyaZ-Waveenabledcontrollerthatsupportthe Z-WaveConfigurationcommandclass.ForacompletelistofAdjustableConfigurations, visit:www.jascoproducts.com/z-waveconfig 2. A B C F G D E A. Up (Press up &
release to turn switch on) B. Down (Press down &
release to turn switch off) C. Ground (Green/Bare) D. Load (Black) E. Line (Black) F. Traveler (Red/Other) G.Neutral (White) Single, Dual And Triple Gang Boxes When installing the In-wall smart switch in multiple gang boxes it may be necessary to break off one or both sides of the scored tabs on the front yoke. This does not affect the electrical rating of the switch (see specifications for details). WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact Customer Service at 800-654-8483 (option 1) between 7:30AM 5:00PM CST or via our website (www.jascoproducts.com) if the unit should prove defective within the warranty period. GARANTIE JASCO Products garantit que ce produit est exempt de tout dfaut de fabrication pour une priode de deux ans compter de la date de lachat original par lacheteur. Cette garantie se limite exclusivement la rparation ou au remplacement de ce produit et nest pas applicable aux dommages indirects ou accessoires survenus sur dautres produits utiliss avec ce produit. Cette garantie se substitue toute autre garantie expresse ou implicite. Certains tats ne permettent pas de restrictions quant la dure dune garantie implicite ou permettent lexclusion ou la limitation des dommages indirects et accessoires; il se peut, par consquent, que cette garantie ne sapplique pas dans votre cas. Cette garantie vous confre des droits juridiques prcis; vous pouvez jouir dautres droits qui peuvent varier dun tat lautre. Veuillez communiquer avec le service la clientle au 1-800-654-8483 (op-
tion 1) entre 7 h 30 et 17 h (heure normale du Centre) ou par lintermdiaire de notre site Web (www. jascoproducts.com) si lappareil savre dfaillant au cours de la priode de garantie. GARANTA JASCO Products garantiza que este producto est libre de defectos de fabricacin durante un periodo de dos aos a partir de la fecha original de compra por parte del consumidor. Esta garanta se limita a la reparacin o sustitucin de este producto solamente y no se extiende a daos derivados o accidentales causados a otros productos que se usen con esta unidad. Esa garanta remplaza a todas las dems garantas expresas o implcitas. Algunos estados no autorizan limitaciones en cuanto a la duracin de una garanta implcita ni permiten la exclusin o limitacin por daos accidentales o derivados; por lo tanto, puede que las anteriores limitaciones no apliquen en su caso. Esta garanta le da a usted derechos especficos, y otros que usted puede tener y que varan segn el estado en el que usted reside. Si la unidad resultare defectuosa dentro del periodo de garanta, comunquese por favor con Atencin al Cliente en el 800-654-8483 (opcin 1) entre 7.30 y 17 h, Hora del Centro, o a travs de nuestro sitio de internet JASCO Products Company, Building B 10 E Memorial Rd. Oklahoma City, OK 73114 908.4/916 MHz SPECIFICATIONS ZW4003 Power: 120 VAC, 60 Hz. Signal (Frequency): 908.42 MHz. Maximum Loads: 960W, incandescent, HP Motor or 1800W (15A) Resistive Range: Up to 100 feet line of sight between the Wireless Controller and the closest Z-Wave receiver module. Operating Temperature Range: 32-104 F (0-40 C). For indoor use only. Specifications subject to change without notice due to continuing product improvement 908.4/916 MHz SPCIFICATIONS ZW4003 Tension : 120 V c.a., 60 Hz. Signal (frquence) : 908,42 MHz. Charges maximales : 960 watts (incandescent), moteur de HP ou rsistance de 1800 W (15 A). Porte : Distance vue entre la tlcommande et le module de rception Z-Wave le plus proche allant jusqu 100 pi. Plage de tempratures de fonctionnement : de 32 104 F (de 0 40 C). Utilisation intrieure uniquement. En raison damliorations continues du produit, les spcifications peuvent faire lobjet de changements sans pravis. 908.4/916 MHz ESPECIFICACIONES:
ZW4003 Energa: 120 VCA, 60 Hz. Seal (Frecuencia): 908.42 MHz. Cargas mximas: 960 W, incandescente, HP motor o 1800 W (15 A) resistiva Alcance: Hasta 100 pies (30.5m) en lnea de visibilidad directa entre el control inalmbrico y el mdulo receptor Z-Wave ms cercano. Rango de temperatura de funcionamiento: 32-104 F (0-40 C). Para uso en espacios interiores solamente. Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto White (Neutral) Green (Ground) Black (Line / Hot) Black
(Load) Z-Wave Single Switch Out to Light (Load) C D B A E From Breaker Box STOP DO NOT RETURN THIS PRODUCT TO THE STORE NE RETOURNEZ PAS CE PRODUIT AU MAGASIN NO DEVUELVA ESTE PRODUCTO A LA TIENDA If you have any problems or questions, contact our tech support team at; 1-800-654-8483, option 1 MondayFriday, 85pm CST For the most up-to-date product support, accessories, electronic (PDF) format manuals and more, visit www.jascoproducts.com/support No user servicable parts in this unit. Si vous avez des problmes ou des questions, communiquez avec notre quipe de soutien technique au 1-800-654-8483, option 1, du lundi au vendredi, de 8 h 17 h (HNC). Pour un soutien technique davant-garde, les nouveaux accessoires, les plus rcents manuels en format lectronique (PDF) et plus encore, visitez le site www.jascoproducts.com/support Aucune des pices de ce dispositif ne peut tre rpare par lutilisateur. Si tiene problemas o dudas, comunquese con nuestro equipo tcnico al nmero: 1-800-654-
8483, opcin 1 de lunes a viernes, de 8 a 17 h, hora estndar del centro (CST). Para recibir el soporte tcnico ms actualizado sobre productos, accesorios, manuales en formato digital (PDF), entre otros, visite www.jascoproducts.com/support Esta unidad no contiene piezas que el usuario pueda reparar. WARNING RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS CONTROLLING APPLIANCES:
EXERCISE EXTREME CAUTION WHEN USING Z-Wave DEVICES TO CONTROL APPLIANCES. OPERATION OF THE Z-Wave DE-
VICE MAY BE IN A DIFFERENT ROOM THAN THE CONTROLLED APPLIANCE, ALSO AN UNINTENTIONAL ACTIVATION MAY OCCUR IF THE WRONG BUTTON ON THE REMOTE IS PRESSED. Z-Wave DEVICES MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED EVENT PROGRAMMING. DEPENDING UPON THE APPLIANCE, THESE UNATTENDED OR UNINTENTIONAL OPERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS CONDITION. FOR THESE REASONS, WE RECOMMEND THE FOLLOWING:
DO NOT USE Z-Wave DEVICES TO CONTROL ELECTRIC HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRESENT A HAZARD-
OUS CONDITION DUE TO UNATTENDED OR UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL. AVERTISSEMENT RISQUE DINCENDIE RISQUE DE CHOC LECTRIQUE RISQUE DE BRLURES COMMANDE DES APPAREILS :
SOYEZ TRS PRUDENT LORSQUE VOUS UTILISEZ LES DISPOSITIFS Z-Wave POUR COMMANDER LES APPAREILS. LE DISPOSITIF Z-Wave PEUT TRE UTILIS DANS UNE SALLE DIFFRENTE DE CELLE DANS LAQUELLE SE TROUVE LAPPAREIL COMMAND ET UNE ACTIVATION INVOLONTAIRE PEUT AUSSI SE PRODUIRE SI LE MAUVAIS BOUTON EST ACTIV SUR LA TLCOMMANDE. LES DISPOSITIFS Z-Wave POURRAIENT TRE ACTIVS AUTOMATIQUEMENT CAUSE DUN VNEMENT PROGRAMM. SELON LAPPAREIL, CES UTILISATIONS INVOLONTAIRES ET SANS SUPERVISION PEUVENT ENGENDRER UN RISQUE. POUR CES RAISONS, NOUS RECOMMANDONS CE QUI SUIT :
NUTILISEZ PAS LES DISPOSITIFS Z-Wave POUR COMMANDER LES RADIATEURS LECTRIQUES OU DAUTRES APPAREILS QUI POURRAIENT PRSENTER UN DANGER EN CAS DE COMMANDE DACTIVATION IMPRVUE, INVOLONTAIRE OU AUTOMATIQUE. ADVERTENCIA RIESGO DE INCENDIO RIESGO DE DESCARGA ELCTRICA RIESGO DE QUEMADURAS CONTROL DE APARATOS:
TENGA MUCHO CUIDADO AL USAR DISPOSITIVOS Z-Wave PARA CONTROLAR APARATOS. EL FUNCIONAMIENTO DE UN DISPOSITIVO Z-Wave PUEDE TENER LUGAR EN UNA SALA DONDE NO EST EL APARATO QUE SE CONTROLA, ASIMISMO, PODRA PRODUCIRSE LA ACTIVACIN ACCIDENTAL SI SE OPRIME EL BOTN EQUIVOCADO. LOS DISPOSITIVOS Z-Wave SE PUEDEN ACTIVAR AUTOMTICAMENTE DEBIDO A QUE ALMACENAN EVENTOS PROGRAMADOS. DEPENDIENDO DEL APARATO, ESTE FUNCIONAMIENTO SIN VIGILANCIA O NO INTENCIONADO PODRA PROVOCAR UNA SITUACIN PELIGROSA. POR ESTAS RAZONES, RECOMENDAMOS LO SIGUIENTE:
NO UTILICE DISPOSITIVOS Z-Wave PARA CONTROLAR CALENTADORES ELCTRICOS NI NINGN OTRO APARATO ELCTRICO QUE PUEDA PRESENTAR UNA SITUACIN PELIGROSA DEBIDO A UNA ACTIVACIN AUTOMTICA SIN VIGILANCIA O NO INTENCIONADA DEL CONTROLADOR. NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT Z-Wave enabled devices should never be used to supply power to, or control the On/Off status of medical and/or life support equipment. NE PAS UTILISER AVEC UN QUIPEMENT MDICAL OU DE SURVIE Les dispositifs compatibles avec la technologie Z-Wave ne devraient jamais tre utiliss pour alimenter ou commander la mise en marche ou larrt de lquipement mdical ou de survie. SE PROHBE SU EMPLEO EN EQUIPO MDICO O EQUIPO PARA EL MANTENIMIENTO DE LAS FUNCIONES VITALES Los dispositivos Z-Wave nunca se deben usar para suministrar energa elctrica al equipo mdico o al equipo para el mantenimiento de funciones vitales, ni para controlar el estado de encendido o apagado de dichos equipo. Out to Light (Load) C D E A B From Breaker Box In-wall Wireless Smart Switch Montage mural sans fil intelligent enfichable Interruptor inalmbrico de pared inteligente Z-Wave Certified Wireless Lighting Control Certifi Z-Wave Commande dclairage sans fil Control inalmbrico para iluminacin certificado por Z-Wave OR Scan to view installation guide Balayez ce code pour consulter le guide dinstallation. Escanear para ver la gua de instalacin 14319 14320 ZW4003 WARNING SHOCK HAZARD Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation consult a qualified electrician. Multi-switch wiring For 3-way installations, please refer to Add-on Switch (45741/45761) manual 1. Shut off power to the circuit at circuit breaker or fuse box. IMPORTANT! Verify power is OFF to switch box before continuing. 2. Remove wall plate. 3. Remove the switch mounting screws. 4. Carefully remove the switch from the switch box. DO NOT disconnect the wires. 5. There are up to five screw terminals on the switch; these are marked A. LINE (Hot) Black (connected to power) B. Neutral White C. LOAD Black (connected to lighting) E. TRAVELER Red/Other (only used in 3-way installations) D. GROUND Green/Bare Match these screw terminals to the wires connected to the existing switch. 6. Disconnect the wires from the existing switch. Be careful to label wires according to the previous terminal connection. Observe Important Wiring Information IMPORTANT!: This switch is rated for and intended to only be used with copper wire. Wire Gauge Requirements Use 14 AWG or larger wires suitable for at least 80 C for supplying Line (HOT), Load, Neutral, Ground and Traveler connections. Wire strip length:
For attachment to screw terminals: Strip insulation 1 (25mm) For attachment using the enclosures holes: Strip insulation 5/8 (16mm) UL specifies that the tightening torque for the screws is 14 Kgf-cm (12 lbf-in). 7. Connect the green or bare copper ground wire to the GROUND terminal. 8. Connect the black wire that goes to the fixture to the terminal marked LOAD. 9. Connect the black wire that comes from the electrical service panel (Hot) to the terminal marked LINE. 10. Connect the white wire to the neutral terminal (use included jumper wire if needed). Note: The Traveler terminal is only used for 3-way or 4-way wiring and should remain insulated if the switch is being installed in a 2-way system (one switch & one load). 11. Insert Switch into the switch box being careful not to pinch or crush wires. 12. Secure the switch to the box using the supplied screws. 13. Mount the wall plate. 14. Reapply power to the circuit at fuse box or circuit breaker and test the system. Basic Operation The connected light can be turned ON/OFF in two ways:
1. Manually from the front panel of the In-wall switch 2. Remotely with a Z-Wave Controller Manual Control The Front Panel Toggle Switch allows the user to:
Turn ON/OFF the connected fixture. To turn the connected fixture ON: Press and release up on the toggle. To turn the connected fixture OFF: Press and release down on the toggle. The Jasco Add-on switch is required for Multi-Switch 3-way or 4-way installations. Connecting the traveler terminal of this switch to a standard, non-Jasco switch will cause damage or result in improper function. If this switch is a part of a 3-way or 4-way multi-switch installation, do not connect the traveler wire or apply power until Jasco Add-on switches are correctly installed. For more information on 3-Way or 4-Way installations, view the manual or quick-start guide that comes with the Jasco Add-on switch. This Device supports Lifeline (association group 1) supporting 1 node for lifeline communication. Group 1 must be assigned the Node ID of the primary controller where unsolicited notifications will be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline association only supports the Device Reset Locally function. Refer to the instructions of your controller for any available details on how this can be set. Adding your device to a Z-wave network:
1. FollowtheinstructionsforyourZ-wavecertifiedcontrollertoincludeadeviceto theZ-wavenetwork. 2. Oncethecontrollerisreadytoincludeyourdevice,pressupandreleasethe toggletoincludeitinthenetwork. theZ-wavenetworktooptimizeperformance. IfyourZ-wavecertifiedcontrollerfeaturesRemoteAccess,youcannowcontrol yourfixturefromyourmobiledevices. To exclude and reset the device 1. FollowtheinstructionsforyourZ-wavecertifiedcontrollertoexcludeadevicefrom theZ-wavenetwork. toexcludeitfromthenetwork. 3. Onceyourcontrollerhasconfirmedthatthedevicehasbeenincluded,refresh 2. OncethecontrollerisreadytoExcludeyourdevice,pressupandreleasethetoggle Please reference the controllers manual for instructions. NowyouhavecompletecontroltoturnyourfixtureON/OFFordim accordingtogroups,scenes,schedulesandinteractiveautomations programmedbyyourcontroller. To return your switch to factory defaults:
1. QuicklypressON(Up)buttonthree(3)timesthenimmediatelypresstheOFF
(Down)buttonthree(3)times.Note: This should only be used in the event your networks primary controller is missing or otherwise inoperable. Z-WAVE INTEROPERABILITY ThisproductcanbeincludedandoperatedinanyZ-Wave networkwithotherZ-Wavecertifieddevicesfromother manufacturersand/orotherapplications.Allnon-battery operatednodeswithinthenetworkwillactasrepeaters regardlessofvendortoincreasereliabilityofthenetwork.