www.badasystem.co.kr User's Manual USER MANUAL Android OTT STB NO-100 Rev.1.1 1. Notice Notice Read this manual carefully and make sure you understand the provided instructions. For your safety, check what the result each action will be. Warnings To reduce the risk of electric shock, do not remove the cover(or back) No User-serviceable parts are inside. Refer servicing to qualified service personnel. Throughout he whole manual, pay special attention to the following marks that indicate hazardous situations. Warnings : Indicates a hazardous situation which, if not avoided, could result in serious injury. Caution : Indicates a situation which, if not avoided, could damage the equipment or apparatus. Note : Indicates additional information to the user to make the user aware of possible problems and information of any importance to help the user to understand, to use and to maintain the installation. When this crossed-out wheeled bin symbol is attached to a product it means that the product is consistent with European Directive 2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products. The logo informs that the receiver is consistent with terms and conditions of Directive 2004/108/EC concerning observance by Member States of provisions regulating electromagnetic compatibility, and to the terms and conditions of Directives 2006/95/EC concerning observance by Member States of provisions refulating low voltage electricity and safety with relation to the handling and operation of electrical equipment. This product has been designed, tested and manufactured according the European CE Directive 2014/53/EC. 1. Notice FCC Compliance Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Connect the equipment into an outlet on a circuit different Increase the separation between the equipment and receiver. from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm. 2. Safety Instructions and Precautions To avoid electric-shock hazards, do not open the housing, refer servicing to qualified personnel only. Do not expose the receiver to direct sunlight. Keep it away from the heat source. When the abnormal phenomenon occurs you should cut off the power supply immediately Switch the receiver off whenever it remains out of service for an extended period. Keep the receiver away from flower vases, tubs, sinks, etc., in order to avoid damaging the equipment. Do not block ventilation holes of the receiver so air can circulate freely. Do not touch the receiver during thunder, since that might create electric-shock hazards. It is recommended to cut off power supply. supply. Do not touch the receiver during thunder, since that might create electric-shock hazards. It is recommended to cut off power 3. Accessories / Components Accessories OTT STB AC Adapter HDMI Cable RCU/Battery User Manual HDMI cable (Type A, high-speed HDMI cable, 4K@60Hz output support), Related equipment such as S/PDIF optical cables are available in the market. Precautions for installation : After connecting the cable, connect the product to power. If the power is turned on during connection damage to this product may occur. Battery precautions If the battery installed in the remote control has reached the end of its lifespan, replace it with a new one immediately. Leaving the dead batteries unattended may cause leakage and cause the remote control to malfunction.
(Especially if you use cheap and poor quality batteries, leakage may occur. Do not use as it can be severe.) 4. Description of the OTT / Installation Front View 1. Power LED :
2. IR Sensor Standby mode: Red / Operation mode: Green Rear View 1. DC 12V : Connect the adaptor DC Jack(DC power in). 2. S/PDIF : Connect to AV Amp.(S/PDIF Optical) 3. HDMI OUT : Connect to TV HDMI input. 4. LAN : Connect to Router's LAN port. 4. Description of the OTT / Installation Side View 1. Micro SD: Insert Micro SD storage for TV-record or Multimedia. 2. USB 3.0 : Connect to USB devices. (USB 3.0 & others) 3. USB 2.0 : Connect to USB devices. (USB 2.0 & others) Insert USB storage for TV-record or Multimedia. Installation : 1. HDMI VIDEOAUDIOLRHDMITV(HDMI)AdapterAmp.(Optical S/PDIF)WiFi Router (LAN or WiFi)1234 4. Description of the OTT / Installation Installation : 1. HDMI Connect the HDMI output terminal of the receiver to the HDMI input terminal of the TV using an HDMI cable
(Type A, high-speed HDMI cable, 4K@60Hz output supported). For details on how to connect to the HDMI input terminal and how to use it, refer to the TV instruction manual. Installation : 2. Network Cable & WiFi How to connect a network cable for high-speed Internet service. Connect the receiver's Internet terminal to the WiFi Router(or home gateway)'s LAN (or ETHERNET) terminal. Installation : 3. DC Cable (Power) Connect the adaptor DC jack to the receiver's DC 12V port. Installation : 4. S/PDIF Connect to devices that support S/PDIF (Optical) interface, such as audio amplifiers and AV receivers. S/PDIF cables can be purchased from the market and used. 5. Troubleshooting Symptom Cause Check Action When the HDMI screen does not appear Is the power plug unplugged?
Are the TV and receiver connected correctly?
Is the TV input selection properly selected?
Is the screen not displayed even if the connection is correct?
When there is no sound Isn't it set to mute?
Is the audio device connected to the HDMI output or optical output cable set to receive the output signal of this unit?
Is the HDMI output or optical output connector connected?
Is there no sound even if all connections are normal?
initial menu screen does not appear. Does normal initial screen not appear when the receiver's power is turned off and then on?
There is no software upgrade. Is the internet cable connected? Are the Wi-Fi settings and the router connection normal?
Insert the power plug into the outlet correctly. Connect the TV and receiver correctly. Press the TV/External input button on the TV to select the input correctly.
(HDMI input) Turn the AC power off and on again. Press the mute button to cancel. Select the correct input mode for the audio device or TV connected to the HDMI output or optical output connector. Insert the HDMI output or optical output connector correctly. Turn the AC power off and on again. Turn the AC power off and on again. Contact customer service. Turn off the power and try again, or contact customer service. The remote control does not work. Are the batteries installed correctly? Are the batteries too old?
Insert the batteries according to the polarity. Replace a new batteries. When the power does not come on Is the power plug unplugged?
Is the power temporarily out of power?
Insert the power plug into the outlet correctly. Operate a light or household electrical appliance. 6. Product Specifications CPU ARM Cortex A55, Quad Core 64bit CPU Cores RTD1319PB (15K DMIPS, REALTEK) High-performance Multicore mailG31-MP2 GPU Storage SDRAM IR (RCU) HDMI Ethernet Wi-Fi USB Ports 8GB eMMC 5.1 2GB DDR4 SDRAM 38KHz Data Receiving , NEC HDMI 2.0aTX with HDCP 2.2, 4K 10bit UHD @60Hz up 4096x2160 RJ45 10/100M Fast Ethernet interface IEEE 802. 11b/g/n, 2.4GHz Single band 1x USB 3.0 port, 1x USB 2.0 port HDMI 2.0, USB 2.0, USB 3.0, S/PDIF(Optical/IEC-6095B), LAN10/100Mbit, Micro SD (up to 128GB), DC 12V Software (OS) Android 10 (AOSP) Video Format 4:3, 16:9, Letter Box, Pan & Scan Video Support 10bit, Up to 3840x2160@60fps, HDR10 support Audio Mode Stereo/Mono/Left/Right/Exchange Audio Decoding MPEGI&II, MP3, AAC-LC, HE-AAC V1/2 Input Voltage DC 12V/1A Power Consumption Max 12W Power Consumption in St andby
< 0.5W Storage Temperature
-10~60C Operating temperature
-0~45C Humidity
<95%
Dimensions (W x D x H) 126 x 122 x 32mm Net Weight 0,28 kg Memo. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. www.badasystem.co.kr Rev.1.1