FCC ID: 2ATPO-A9 GPRS Module

A9 GPRS/GSM MODULE V1.3 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body:

Use only the supplied antenna. FCC ID: 2ATPO-A9 Copyright2019 ShenzhenAi-ThinkerCo.,LtdAllRightsReserved A9 GPRS/GSM MODULE V1.3 A9 GPRS Module l The A9 development board is a multifunctional development board based on the A9 GPRS / GSM module. It can be used to verify the basic communication functions and peripheral f unctions of the A9 module. l A9 development board has basic phone / SMS, GPRS network communication. l A9 development board has lithium battery charging management, microphone, speaker interface, USB communication interface, multiple user buttons / led, TF card slot, acceleration sensor, SPI interface, I2C2 interface, ADC interface l A9 development board camera expansion board, which can connect 30W / 200W camera. l A9 development board slot machine expansion board, which can be connected to traditional slot machines. Based on the above functions, A9 can be used for a variety of peripheral prototype development and verification:

l Vehicle anti-theft device using GPRS and acceleration sensor. l Remote monitoring intercom using GSM and microphone / speaker l Smart watch using GPRS / GSM, 1.54-inch capacitive touch screen l Elderly monitoring watch using GPRS / GSM, heart rate blood oxygen sensor, 1.54 inch capacitive touch screen l Remote monitoring camera using GPRS + TF + camera expansion board l Wechat payment slot machine solution using slot machine expansion board Copyright2019 ShenzhenAi-ThinkerCo.,LtdAllRightsReserved Features Overview A9 GPRS/GSM MODULE V1.3

- Complete quad-band GSM / GPRS module, 800/900 The A9 is a complete quad-band GSM / GPRS module in

/ 1800 / 1900MHz

- SMD package for easy MP & testing

- Low power mode, average current 2mA or less a compact design SMD package. Its stable performance, the appearance of compact, cost-effective, could meet the diverse needs of customers. The A9 can be used in a wide range of IoT applications

- Supports digital audio and analog audio, supports and is ideal for IoT applications for home automation, HR, FR, EFR, AMR voice coding

- Support voice calls and SMS messages

- Embedded network service protocol stack

- Support standard GSM07.07,07.05AT command and Anxin expandable command set

- Support PBCCH

- Supports firmware upgrade via serial port industrial wireless control, wearable electronics, wireless location sensing devices, wireless location system signals and other IoT applications. A9 SMD package, through the standard SMT equipment to achieve rapid production of products, especially for automation, large-scale, low-cost modern production methods for the convenience of a variety of Internet of Things hardware terminal applications. Copyright2019 ShenzhenAi-ThinkerCo.,LtdAllRightsReserved Text support Current PBCCH Class 12 CS 1,2, 3, 4 Power supply AT command Coding scheme GPRS Class 12 GPRS Multi-slot 3GPP TS 27.007, 27.005 3.8~4.2Vtypicalvalue4.0V A9 GPRS/GSM MODULE V1.3 Max 85.6kbps (up & down 1.14mA@DRX=5 1.03mA@DRX=9 Product Specifications Model Name Package Size Frenquency GPRS Mobile Station Compatible with GSM Phase 2/2+

Class B Class 4 (2W@850/ 900MHz) Class 1 (1W@1800/1900MHz) Point to point sms send and receive Cellular broadcast message Text / PDU mode A9 SMD54 19.2*18.8*2.9(0.2)mm 850/900/1800/1900MHz Contact USAi-Thinker 3pcs (including firmware upgrade serial port)baud rate support 2400~1843200bps, default115200bps Half Rate (HR) Full Rate (FR) Enhanced Full Rate (EFR) Adaptive Multi-Rate (AMR) Address:410, Building C, Gufeng Huafeng Smart Innovation Port, Xixiang, Baoan District, Shenzhen Echo Cancellation Echo suppression Noise suppression I2CUSBUARTSDMMCGPIOADC Audio processing mechanism Copyright2019 ShenzhenAi-ThinkerCo.,LtdAllRightsReserved Communication Interface Shenzhen Ai-Thinker Technology Co., Ltd E-mail: support@aithinker.com Website: www.ai-thinker.com Working Temperature Voice coding mode Tel: 0755-29162996

-20C~+70C About 3.0g SIM Card 1.8V/3V Antenna Weight UART Pad OEM/Integrators Installation Manual Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable 4. configurations with respect to Part 2.1093 and different antenna configurations

. For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module's intentional emissions are compliant (i.e. fundamental and out of band emissions). The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s). The Grantee will provide guidance to the host manufacturer for Part 15 B requirements if needed. End Product Labeling When the module is installed in the host device, the FCC/IC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: Contains FCC ID: 2ATPO-A9 The FCC ID can be used only when all FCC compliance requirements are met. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/IC authorization. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Information for the OEMs and Integrators about antennas The EUT is a mobile device; maintain at least a 20 cm separation between the EUT and the users body. If the user changes the same type of antenna and the antenna gain is greater than 3dBi, the module needs to be reevaluated. If the antenna gain is less than 3dBi, the module still meets the requirements

1 4 9,3 17, 2 0,2 U N FCC ID: 2ATPO-A9 SN:A06V022016030801 GPRS/GSM A9 N 1, 2

Shenzhen Ai-Thinker Technology Co., Ltd Agent Authorization Company: Shenzhen Ai-Thinker Technology Co., Ltd Address: Room 701, Building B, Huafeng Industrial Park, Hangkong Road, Sanwei Community, Baoan District, Shenzhen, China Product Name: GPRS Module Model Number(s): A9 Product Description: GPRS Module We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Title:

Company: Shenzhen Ai-Thinker Technology Co., Ltd facheng su manager Date: 01/13/2020

Shenzhen Ai-Thinker Technology Co., Ltd Modular Transmitter Approval Request Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD21046 Company name: Shenzhen Ai-Thinker Technology Co., Ltd FCC ID: 2ATPO-A9 Gentlemen, In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 Module Certification Guide v01r04. FCC ID: 2ATPO-A9 has been examined against the following requirements. Requirement per 15.212 and KDB 996369 D01 The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal The module must contain power supply regulation on the module The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) The module must demonstrate compliance in a stand-alone configuration The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labeling requirements) The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee The module must comply with RF exposure requirements Explanation from Grantee

(do not write yes/no, but explain why product complies/how it is achieved) Yes, the products have a shield, Physical components and tuning capacitor(s) are assembly to the module and located internal to the shield. Yes, The module has buffered modulation/data inputs. Yes, The modular transmitter has its own power supply regulation. Yes, The module contains a permanently attached PIFA Antenna. Yes, The module compliance in a stand-

alone configuration. Yes. The module has its permanently affixed FCC ID label and the FCC ID label is laser engraved on the shield. The module complies with all specific rules applicable to the transmitter. Yes. We provided an MPE report to show the module comply with RF exposure requirements. Name: facheng su Title: Manager Date: Jan. 15. 2020 Signature of applicant :

FCC Modular Approval Request Rev 2.0

< Shenzhen Ai-Thinker Technology Co., Ltd >

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Date: 2020/01/13 Subject; Request for Confidentiality FCC ID: 2ATPO-A9 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

Schematic Diagram Block Diagram Operational Description BOM and turn up procedure External Photos Test Setup Photos Internal Photos User Manual OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: facheng su Title: manager

ShenzhenAiThinkerTechnologyCo.,Ltd Date: Jan. 13 2019 FCC ID: 2ATPO-A9 Model Number: A9 To:

Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21048 To Whom It May Concern, We, Shenzhen Ai-Thinker Technology Co., Ltd declare that this EUT (FCC ID:

2ATPO-A9) will conduct FCC compliance testing, the SDOC part recognized test lab(Shenzhen NTEK Testing Technology Co., Ltd.( ShenZhen Lab.). 1/F, Building E, Fenda Science Park, Sanwei Community,Xixiang Street Baoan District, Shenzhen 518126 P.R. China) Please contact me if you have any question. Sincerely,

(Signed) Name/Title:fachengsu/manager Company:ShenzhenAiThinkerTechnologyCo.,Ltd Address: Room 701, Building B, Huafeng Industrial Park, Hangkong Road, Sanwei Community, BaoanDistrict,Shenzhen,China