Packing List After opening the package, please make sure the doorbell
(hereinafter referred to as theEquipment) is in good condition verify parts below is complete. Equipment
(including Conductivethe installation support) Security Screw Quick Start Guideline Visual wireless doorbell M7 Quick Start Guideline
* Please read it carefully before using the product, and safe keeping Screw Package (including screws) Quick Start Guide Appearance Introduction Lens Indicator Light PIR Light Sensor IR LED MIC Button Speaker IR LED The ambient light is not enough, to enable the infrared light, increase the environmental brightness Light Sensor Used to collect environmental brightness value, when the intensity of illumination is less than 2 Lux, enable the IR LED MIC Button PIR Audio capture The doorbell button When human body movement in front of the equipment, the equipment could be made the notification to your mobile phone. Lens Video image capture Indicator Ligh Blinking blue: configuration status;
Long red light: failed to connect wifi;
Blue light is on: the device is connected successfully Red and blue light together: The device is connected to WiFi Speaker Make a sound of the equipment, and voice intercom USB Interface TF card Reset Button AC Input Battery Comartment Fixed Hole AC Input Power is supplied to the equipment by installing the AC input supply hole on the mounting bracket. Reset Button Equipment working status, long press 5 seconds to restore factory settings Battery Compartment Mounting 18650 specification battery. Fixed Hole AC Input Hole Fit the support on the wall with the mounting screws for the mounting kit. The power supply of the equipment can be supplied by connecting the hole and the AC power supply on the wall Stuck Hole Mounting the equipment onto the bracket Security Screw Hole TF card Mounting the security screw on the fittings to prevent the equipment from being removed TF card maximum support 32G Installation Guide As shown in the figure, take back 3 4 Mounting three 18650 specification batteries Press the reset button for 5 seconds, waiting for the indicator light to slow down(The equipment should be in working condition, long press, sleep state is invalid) 5 Cover the battery cover, align the equipment and the bracket, push down and lock the security screws to complete the installation Setup Device Thank you for choosing our products! Please follow the below instruction to setup and using your doorbell device. 1. Downloading and Installing the App Open the App Store (for iOS) or the Google Play Store(for Android) on your mobile devices. Search for "Ubell" or scan the following QR Code to download and install to your device. 5.) The name of the Wi-Fi network will automatically be filled in, enter the Wi-Fi password. And adjust the volume of your device to a reasonable level then tap "Next". The APP will fill the corresponding password automatically if connected with the same Wi-Fi, and you don't need to fill the password again. App iOS App Google play APP-Android 2. Setting up the App Before you begin
> Make sure the Ubell app is installed to your device.
> Make sure that your device is connected to a 2.4GHz Wi-Fi network, NOT a 5GHz network. Add the camera 1.) Launch the Ubell app on your device and tap Add a Camera. Seup the Camera 2.) Select Setup Camera. Note: If you have multiple cameras, only setup one at a time. 6.) The mobile device will emit sound waves, keep quiet and make sure about 30cm distance between the phone and the device , and waitting for the device to configure the network. If your camera fails to connect, reset the camera and repeat all the steps(please s ee the previous section, Resetting the Camera) 1 2 Use the screws in the mounting kit to fit the bracket on the wall cennect the external power cord to the AC external power supply hole 7.) After a successful connection, you will be prompted to create a name and password for your camera. The password must be at least 8 characters and include an uppercase letter, a lower-case letter, and a number. 3.) Before setup, make sure the device is in configuration --- with a voice prompt "The camera is now ready to begin pairing". 4.) If you didn't hear the voice prompt, press and hold the reset button for 5 seconds. Release after the LED indicator turnned off , and the device will restart to configure automatically. 8.) Setup completed! The APP will be entered the device list interface automatically. Congratulations!
The device is ready for use. 5.Cloud Storage Note: In crowded environment, it is recommended to close or set the device to low sensitivity to reduce device arousal and call times to extend battery life. In the XSHcam APP setting menu, choose storage manag-
ment, and open Cloud Storage At the bottom of the preview page, the "Switch" button in the panorama mode becomes the
"Cloud Storage" button 6.Note for using 3.The Wi-Fi Doorbell Features In the device list section, please click settings icon which at the top right corner to enter the device settings. Set up Call reminding QR code Deleting equipment Accept call Turn on - Receive the notification if somebody press the doorblle or call out. Turn off - Will not receive the notifications for accept call. Call reminding Share QR Code Send the QR code to share the device to your friends and family or someone that you want to share. QR code Delete camera The mobile device will not receive the notifications after you delete the camera. But the camera still works and the other connected mobile devices still able to receive the notifications. Deleting equipment 4.PIR Detection Instructions The device can support the PIR detection. Tap "PIR detection" to open the submenus. Disabled - Close the PIR function. Low -
The device will be able to wake up after device detects human for 7 seconds. Device start to take videos and call the mobile device at the same time. Medium -
The device will be able to wake up after device detects human for 5 seconds. Device start to take videos and call the mobile device at the same time. High -
In the state, the device will be able to detect if keep the state what be detected at least 1 second, and the device start to take videos and call to phones at the same time. Cloud Storage Description: When the device is in sleep state, when PIR triggered or the doorbell button was pressed , the device will automatically upload 10 seconds of video to the cloud. Each device can record 20 events per day, and provide a week of loop recording space and Traffic for users Tap the calendar icon in the upper right corner and select the date to see all the cloud videos for the selected date Click on the event video to see the cloud video 1.) The device is powered by rechargeable lithium batteries. With fully charged, the battery life approx be six months. The mobile device APP will be prompted while the battery voltage is low. Please charge the device after received the reminder. 2.) Keep the camera in range of your router. Make sure to pick a place within range of your network. Thick or insulated doors can greatly reduce the strength of your Wi-Fi signal even if your router is close by, so you should try streaming video before you mount your camera. 3.The device is a low power consumption intelligent products, can support remote wake up from the APP, PIR human detection, press doorbell wake up. The device will be works for 30 seconds after wake up then be in the resting state automatically and until to next waking up. Technical Specification Resolution 1280* 720 Field of Angle View 166 IR LED Wi-Fi Audio Recording Storage Battery Device Wakeup 6*850mm IEEE 802 11 b/ g/ n Two-way talk with noise cancellation Device SD Card recording(20 seconds) Cloud storage or 8G/16G/32G TF Card Two18650 specification batteries Device Button, Motion Detection, Remote Live View Power Consumption Three pcs 18650 lithium battery Monitoring Notifications Within600 ms Power Consumption Standby200 uA, Working170 mA Three 18650 specification batteries, work regularly for 9 months. Ding-dong Pairing
(Needs to be purchased separately) Code Pairing: 1.Short press the button of Ding-dong responder, indicator light is always on 2.Press the button of doorbell to make the code successful Reset: 1.Press the button of Ding-dong for 5 seconds. Number of connections: 1 Ding-dong can connect with12 Doorbells;
1 Doorbell can connect with unlimited amount of Ding-dongs. Function Introduction Three 18650 specification batteries work regularly for 9 months Million HD pixels collocated with wide-angle lens Support mobile phone remote fast wakeup device within 1 second. 2.4G Wi-Fi connection High quality two-way talk with noise cancellation Support PIR motion detection,when someone hovers at the door, immediately alerts push notifications to the mobile phone. Day and night mode automatic switching, whether day or night, the image is clearly visible, for yoursafety and family security. 20C