FCC ID: 2AURP-G11 Gaming Headset

*:90*120mm Package Contents Power ON Bluetooth Pairing Connection Methods Battery Low Indicator Use the Microphone Gaming Headset Instruction Manual Gaming Headset Instruction Manual Bluetooth gaming headset Instruction manual Bluetooth transmitter USB-C charging cable Press and hold for 2 seconds Press and hold for 5 seconds Overview Hear the prompt sound power on, the blue light is on for 1 second. The light ashes red and blue alternately, select G11"

on the connected device. ON G11 XXX XXXXXX XXX 1. Standard Bluetooth (Default mode at rst boot) Fast press the MFB button 3 times, the headset will switch to Standard Bluetooth mode, you will hear a prompt sound Bluetooth mode". Press and hold the MFB button button for 5 seconds for the rst time, search for the Bluetooth device name G11", select the connection and complete the pairing, you will hear a prompt sound connected". xxxxx G11 XXX XXXXXX XXX After the prompt sound connected, the pairing is successful and the blue light will ash once every 10 seconds. Turn on Bluetooth on your phone, search for G11" to pair When the voltage is low, the red light ashes quickly, and the prompt sound battery low. When the voltage is too low, the headset will automatically shut down, the red LED light will be on for 1 second and then turn o, and you will hear a prompt sound power o. Soft protein leather earpads Adjustable headband Power OFF Bluetooth Reconnection 2. Fast Speed Bluetooth Fast press the MFB button button 3 times, the headset will switch to Fast Speed Bluetooth mode, you will hear a prompt sound dongle mode. Insert the Bluetooth transmitter into the device, and the device will automatically connect successfully, you will hear a prompt sound connected". Headphone Charging Microphone Model: G11 Volume wheel LED indicator Microphone switch Multifunction(MFB) button 3.5mm audio interface USB-C charging port Press and hold for 5 seconds Hear the prompt sound power o, the red light turns on for 1 second and then turns o. If there is a connection record, in the o state, press and hold for 5 seconds to enter pairing, you may hear a prompt sound connected, the connection is successful and the blue light will ash every 10 seconds. Note: When you disconnect the current device or the headset is out of the transmission range, the headset will automatically enter into the reconnection mode, and a prompt sound disconnected, pairing will be heard. Insert the transmitter to USB port Notice:

1. The pictures in this manual are schematic diagrams, and due to technology and system upgrades, the marked information and parameters may deviate from the real objects, please refer to the real objects. 2. The headset and the transmitter are bound one-to-one at the factory. Please keep it properly. Steady red light Red light o, blue light on Ensure the headset is power o before charging. When fully charged, unplug the USB cable and press the power button to turn on the headset. 360 Adjustable microphone Retractable microphone Microphone diaphragm Air vent Adjust the microphone until it is parallel to your mouth. Make sure the microphone diaphragm is in front and the air vent is facing away from your mouth. USB charging port Note: The microphone is turned on by default. Low Latency Game Mode Play the Music Volume Control Colorful Lights Product Specications Kind Tips Safety Information 2 3 4 5 6 7 The headset is booted into game mode, ultra-low latency, crystal clear sound. Single press Pause/Play In the music status, single press the MFB button to pause/play. Double press Next track When playing the music, double press the MFB button to switch to the next song. Scroll up the wheel to increase the volume. Scroll down the wheel to decrease the volume. Model G11 Battery capacity 600mAh Press and hold for 3 seconds Press and hold the M button for 3 seconds to turn on/o the colorful LED.

(Breathing light, multiple colors) Note: The LED lights are on by default, and the lights of left and right sides are synchronized. Working time Charging time Speaker driver 23h (colorful lights on + max volume) 35h (colorful lights o + max volume) 2h 50mm Frequency response 20Hz-20kHz Sensitivity 1053dB Microphone sensitivity 423dB Input power Working distance 5V/1A 10m Wired Connection Call Operation Microphone ON/OFF Factory Reset (Please use with caution) 3.5mm Audio To use the headset in wired mode:

Connect the 3.5mm headphone cable to the headphone jack of the headphone. Insert the 3.5mm headphone cable into the 3.5mm port of the device being used. Single press Answer/Hang up a call In the incoming call status, single press the MFB button to answer/hang up a call. Press and hold for 2 seconds Reject a call In the incoming call status, press and hold the MFB button for 2 seconds, a beep prompt sound will be heard. Single press Press the M button, the light will turn on, and you will hear a prompt sound microphone on. Press the M button, the light will turn o and you will hear a prompt sound microphone o. Note: the microphone is on by default. Fast Press 7 times In the pairing status, fast press the MFB button 7 times, when the prompt sound clang clang clang is heard, the factory reset is completed. Before using the device, please read the instructions carefully and comply with the following cautions. 1. When using for the rst time, please fully charge the headset rst. 2. If you don't use the headset for a long time, be sure to store it in a dry place away from extreme temperature conditions and dust, and make sure to charge it once a month. 3. If the mobile phone cannot pair with the Bluetooth headset, please conrm whether the Bluetooth headset is in pairing mode". If it has not been paired or connected for a long time, the Bluetooth headset pairing function will be turned o. Please turn on the Bluetooth headset again to pairing mode". If there is an error in the Bluetooth headset program, please restart the Bluetooth headset or do the factory reset as instruction above; if the mobile phone program is wrong, please restart the phone. Maintaining Your Headsets Do not expose the headset to liquids, moisture or humidity as it is not waterproof. Do not use harsh chemicals, cleaning agents to clean the device or its accessories. Wipe the device or its accessories with a clean, dry, soft cloth. Do not expose the headset to extreme temperatures. The best storage temperature range is 0C-45C/32-113, otherwise it will aect the service life of the headsets. Do not put the headset in a re as this may cause an explosion. Do not allow your headset to touch sharp objects, as this can cause scratches and damage. Do not attempt to disassemble the headset as it contains no serviceable components. When you use the headset to listen to the music or calls, it is recommended to use the minimum sound level required to avoid hearing damage. Using the headset at high volume for extended periods of time may cause permanent hearing damage. Please do not increase the volume for noise isolation. Before wearing the headset, turn the volume down to the lowest level, then slowly raise it to an appropriate and safe level. If you experiencing ringing in your ears after listening with the headset, it means the volume is too high. Check your local laws regarding the use of cell phones and headphones while driving. If you use the headset while driving, ensure your attention and focus remains on the road and you drive in a responsible and safe manner. If you are using headset during activities that require concentration, take care for your own safety and the safety of others, such as when walking on the streets, construction sites and railways, remove the headset or adjust the volume so that you can hear to surrounding sounds, including alarms and warning signs. In order to avoid danger caused by accidental swallowing, keep the headsets and its accessories away from children and pets. Do not place sharp metal objects such as pins near the earpiece or speaker of the device, so as not to adhere to the metal objects and cause injury to you. Do not use the device in thunderstorm weather, thunderstorm may cause the device to work abnormally and increase the risk of electric shock. Pay attention to all signs requiring electrical equipment or RF radio products to be turned o in designated areas. These may include hospitals, blast areas and potentially explosive environments. Do not install or store the headset in any air bag deployment area as serious injury may result when the air bag deploys. Improper reassembly may result in electric shock during subsequent use of the headset. Avoid charging the headset in extreme temperature conditions. Do not open or damage the built-in battery. Environmental Protection Do not dispose of this device and its accessories as normal household waste. Dispose of this device in accordance with local regulations and support recycling. 8 9 10 11 12 13 14 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15

Inverted F Antenna Specification ANT SPEC 2.4G ANT Horizontal Vertical 2400MHz 2400MHz 2500MHz 2400MHz 2400MHz 2500MHz

-1.26

-0.76

-0.58

-5.25

-2.46

-1.86

-0.58dBi Horizontal and Vertical Omni-directional 50 Ohm 22mm PCB antenna Summary ITEM Model Name Center Frequency MAX. Gain Polarization Azimuth Beam Pattern Impedance Antenna Length Antenna Type Manufacture ZHUHAI JIELI TECHNOLOGY CO., LTD AddressNo.333, Kexing Road, Nanping Town, Zhuhai, Guangdong Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Frequency

(MHz) 2400 2450 2500 Max

-1.26174

-0.765802

-0.585582 Gain(dBi) Min

-30.0801

-36.5604

-22.0315 Avg

-7.18716

-7.48023

-6.59127 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Frequency

(MHz) 2400 2450 2500 Max

-5.2537

-2.4652

-1.86120 Gain(dBi) Min

-22.1424

-24.5837

-29.5214 Avg

-12.4294

-10.4702

-9.20432

7/F, A1 Bldg, Shuichanjingwan Industrial 1st Area, Gushu, Bao'an, Shenzhen, China SHENZHEN AKAUDIO CO., LTD Date01-10-2024 Product Model Number: G11, G10, G20, G520 FCC ID2AURP-G11 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:

Testing Approval applications and procedures We declare that ORGANIZATION. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by ORGANIZATION. on our behalf shall have the same effect as acts of our own. By: Charles Lau Contact Listed on FCC Wesbite Title: General Manager Email: sales@theakaudio.com Telephone: +86 755 29305259 On behalf of: SHENZHEN AKAUDIO CO., LTD

7/F, A1 Bldg, Shuichanjingwan Industrial 1st Area, Gushu, Bao'an, Shenzhen, China SHENZHEN AKAUDIO CO., LTD Jan.11, 2024 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID : 2AURP-G11 Model Number: G11, G10, G20, G520 To Whom It May Concern:

We, The SHENZHEN AKAUDIO CO., LTD hereby declare that the models are identical except the model name. Except for the different above, no other modification is performed. Sincerely, Signature:

Contact person: Charles Lau

SHENZHEN AKAUDIO CO., LTO TIF, Ai Bldg, Shuichanjingwan Industrial 1st Area, Gushu, Bao'an, Shenzhen, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2024-01-10 Subject; Request for Confidentiality FCC ID: 2AURP-G11 To Whom It May Concern, Pursuant to the provisions of the Commission's rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market.

& Schematic Diagram Block Diagram 0 Parts List X) Operational Description C) Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

0 External Photos 0 Test Setup Photos CO Internal Photos

(1 User Manual C For 45 days, pursuant to Public Notice DA 04-1705. OR CO For 180 days pursuant to KDB 726920 D01. Itis our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely eae Lau

7/F, A1 Bldg, Shuichanjingwan Industrial 1st Area, Gushu, Bao'an, Shenzhen, China SHENZHEN AKAUDIO CO., LTD Section 2.911(d)(7) USA Agent for Service of Process FCC ID: 2AURP-G11 2.911(d)(7) USA Designated Agent for Service of Process We, [SHENZHEN AKAUDIO CO., LTD] (the applicant) designate [National Cellular USA, Inc] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Applicant Company name: National Cellular USA, Inc Company name: SHENZHEN AKAUDIO CO., LTD Address: 16 McKinley st,Linden NJ 07036 United States Address: 7/F, A1 Bldg, Shuichanjingwan Industrial 1st Area, Gushu, FRN: 0034081067 Contact Name:Mark Grossman Bao'an, Shenzhen, China Contact Name: Charles Lau Telephone No: (171) 836-9956 0 Telephone No: 86-0755-29305259 Email: purchasing@natcellular.com Email: sales@theakaudio.com Signature:

FRN0028878478 Signature:

Date: 2024.1.3 Date: 2024.1.3 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-communications-supply-c hain-through-the 2.911 (d)(7)USA Agent v1.2

SHENZHEN AKAUDIO CO., LTD TIF, A1 Bldg, Shuichanjingwan Industrial 1st Area, Gushu, Bao'an, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 01-10-2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AURP-G11

[SHENZHEN AKAUDIO CO., LTD] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, GB signature)

(Charles Lau) SHENZHEN AKAUDIO CO., LTD TIF, A1 Bldg, Shuichanjingwan Industrial 1st Area, Gushu, Bao'an, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 01-10-2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AURP-G11

[SHENZHEN AKAUDIO CO., LTD] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely,

(Charles Lau)