FCC ID: 2ATCH-AK210522 Robotic Vacuum Cleaner

 

A90 Robotic Vacuum Cleaner User Manual

Please read this instruction carefully before usage and keep it properly

Important Safety Instructions

1

．

• If you have special objects that could potentially be damaged by the bumping，remove these objects from the floor.

• Do not let kids sit or stand on Robot. Children and pets should be supervised when Robot is operating.

• Do not make Robot for outdoor use.

• Do not clean wet messes with your Robot.

• Do not use Robot to pick up spills of water bleach, paint, and other chemicals.

• Do not keep Robot at a freezing temperatures.

• Do not use Robot to pick up flammable materials such as gasoline. printer, etc.

• Ensure that Robot cannot get caught on clothing, socks, pull cords for blinds or curtains, power cords, etc.

• Only charge the following amarey batteries: maximum 14.4V,2600mAh Lithium-ion battery. Other type of batteries may

burst causing injury. Always contact amarey Customer Service Center for the correct replacement of battery.

• Always remove the battery from Robot and accessories before long-term storage or transportation.

• The battery must be removed before Robot is disposed. Remove Robot's two Battery Door's screws, and then remove

the battery by disconnecting the quick connector.

• WARNING Chemical Exposure: If the battery pack is leaking, do not allow the liquid to come in contact with skin or eyes.

If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Place the

battery (the used battery pack included when the robot will be disposed) in a sealed plastic bag and dispose of safely

according to local environmental regulation.

• WARNING Fire or Explosion Hazard: Do not crush or dismantle battery packs, Do not heat or place the battery

1

 the battery pack near any heat source or direct sunlight, Do not incinerate or short-circuit the battery pack. Do not subject

batteries to mechanical shock.

Battery and Charging/Information

Lithium-ion Battery

Important: Lithium-ion batteries and products that contain Lithium-ion are subject to stringent transportation regula-

tions. If you need to ship this product (with the battery included) for service, travel or any other reason, you MUST

comply with the following shipping instructions:

• Remove the Lithium-ion battery from the product.

• Place a piece of tape over the battery's metal charging contacts.

• Reinstall the battery (with the tape on it) in the product and secure the battery door.

• Pack the product in original packaging or in your own packaging that prevents any movement during transportation.

• Ship via ground transportation only(no air shipping).

Battery Storage

• If storing Robot a long time, remove the battery firstly. Then store Robot and the battery in a cool, dry place.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

2

(1) This device may not cause harmful interference,

(2) This device must accept any interference received, including interference that may cause undesired operation. Any

Changes or modifications that not expressly approved by the party responsible for compliance could void the user's authori-

ty to operate the equipment.

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

CE Warning

1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

2. Adapter shall be installed near the equipment and shall be easily accessible.

3. The operating temperature of the device can’t exceed 40℃ and shouldn’t be lower than 0℃.

4. The plug considered as disconnect device of adapter.

5. The device complies with RF specifications when used at 20cm from the body.

Hereby, Shenzhen Ankobot Robot Co.,Ltd declares that this product is in compliance with essential requirements and

other relevant provisions of Directive 2014/53/EU. This product is allowed to be used in all EU member states.

3

2．About Your Amarey A90

①.Top View

②.Bottom View

Infrared Bumper

Charging Contact Points

Cliff Sensor

Camera

Wi-Fi Indicator

Wi-Fi Indicator

Start/Pause

Start/Pause

Swivel Wheel

Side Brushes

Wheel

Rolling brush

Dust Bin

Main Power switch (On/Off)

4

③. Dust Bin

Primary Filter

Primary Filter

Upper cover of Dust Bin

Upper cover of Dust Bin

5

Filter Lower Cover

High Efficiency Filter

Sponge Filter

Filter Upper Cover

Bin Release Button

④.Charging Dock/Adapter

Adapter

Charging indicator

Signal emission Area

Charging Contact Points

6

⑤.What’s in the Box

amarey A90

Charging Base

4 X Side Brush

Sponge Filter and

High Efficiency Filter

Cleaning Tool

Adapter

7

3．Using Your Amarey A90

①.Important Tips Before Using A90

Before robotic vacuum works, please refer to the following guidelines to check the cleaning area.

Remove power cords and

A90 is not suitable for

Anti-fall sensors can prevent

Keep A90 away from

small objects from the floor

long-pile carpet. If the carpet

A90 from falling down stairs.

spaces lower than 2.4

that may entangle A90.

has tassels, please roll up

But it may work less

inches to prevent A90 from

them before usage.

effectively if sensor is dirty or

getting stuck. If necessary,

work on reflective or very

place a barricade to block

dark floor. It is recommended

off the area or elevate your

to place a boundary strip to

appliance.

block off.

8

②. Preparations

1

Position the Charging Base on a hard level surface and against a wall.

）

（

Ensure the place is an open & uncluttered area leaving at least 4ft in the front and 1.6ft on both sides.

2

Connect the round end of the adapter into the power socket on the Charging

Connect the round end of the adapter into the power socket on the Charging

（

Dock and the other end into a wall outlet. When connect well, the white light will

Dock and the other end into a wall outlet. When connect well, the white light will

）

be on. Otherwise, the robot can’t dock.

9

3

Before usage, Please remove the protective strips.

（

）

protective strip

Protective strip

(4) Install the side brushes by pressing them into each slot until you hear the a “click”.

10

5

Turn on the Main Power Switch at the bottom of Robot (1 refer to power on, 0 refer to power off). The robot can start

）

（

working after startup music.

③. Charging Robot

Place robot onto the Charging Dock, ensure the Charging Contact Points on

Charging Dock and the bottom of robot are contact well. The robot will start

charging after hearing “in charging”. Battery fully charged may cost around

4.5h.

Tips: 1. The robot can’t power on when in low battery. Please turn on the power

switch at the bottom and put robot on charging base, the device will power on

automatically. When the power >20%, it can work normally.

2. Lithium battery pack is built in the robot. To maintain battery performance,

please keep the robot in charging state.

11

④. Download and Install APP

(1) Download and install app

(2) Reset Wi-Fi

(2) Reset Wi-Fi

Download APP by scanning below QR code.

Press the key “ ” for 5S, and you will hear voice prompt

Press the key “ ” for 5S, and you will hear voice prompt

"Reset WI-FI, enter network configuration mode", and the blue

Wi-Fi indicator will flash rapidly, which means the robot start

entering network configuration mode.

Enter the home page of APP, click "+" in the upper right corner and add device according to the APP prompt. The device will

·Due to App upgrading, the operation may have little difference with above instruction, please follow the instruction in APP.

(3) Add device

show in the home page list after successfully added.

Tips:

·Only support 2.4GHz WIFI, not 5GHz.

12

Method 1: Power on robot, after the startup music, press button on panel, auto cleaning will start.

Method 1: Power on robot, after the startup music, press button on panel, auto cleaning will start.

Method 2: Click the “Start cleaning” button thru APP to start cleaning (press the pause button to pause the current task).

If power is less than 20%, Robot will not be able to carry out cleaning task, please charge it before next cleaning.

If power is less than 20% during cleaning, the robot will dock to charging base. When power up to 80%, it will start resume

⑤.Clean Mode

(1) Auto Cleaning

Reminder:

cleaning.

(2) Spot Cleaning

Click Spot cleaning on APP Remote Control interface. After hearing

Click Spot cleaning on APP Remote Control interface. After hearing

“Start Spot Cleaning”, the robot will clean in “Spiral” route. When cleaning

is finished, robot will keep in standby mode.

13

Schedule cleaning can be set thru APP. The robot will automatically start cleaning at the specified time you set and return to

(3) Schedule Cleaning

the charging base after cleaning.

(4) Smart Area

1.Area cleaning

After Smart Map generated successfully, the user can divide the map into

different areas according the cleaning needs. You can set one or more cleaning

areas. Select the areas to clean after setting, the robot will only clean the select-

ed area, and do not clean other areas.

2.Set up boundary area

In addition, some areas can be set as forbidden zones. The robot will not enter

the boundary area after setting, only clean other areas.

C

A

D

B

• Please make sure the robot has completed the smart map building before use this function. Re-building map will lose the

Reminder

：

boundary area you set before.

14

• The boundary area may be invalidated due to moving the charging base or furniture. So please do not to move or interfere

the robot during cleaning.

Due to APP updating, the functions and details may have some changes, please refer to the actual version.

(5) Docking Mode

：

base to recharge.

Auto mode

When the battery power is low, Robot will prompt “Low power, start docking mode”, and start finding charging

Manual mode

In any cleaning mode, press clean key twice or use app control, after voice prompt "start docking mode”, the

：

robot will automatically find the charging base to recharge.

6

Power Off

）

（

If the robot is not used for a long time, please power it off thru turning off the power switch at the bottom.

15

4．Product Maintenance

Tip: Before maintenance of the robot and spare parts, please turn off the main switch at the bottom.

①.Dust Bin

Press Bin Release Button to remove dust bin and clean it.

Tip: Please empty the dust bin after each usage.

16

②.Filters

1

（

）

Take the filters out from the Dust Bin.

2

Clean the Dust Bin and filters with provided Cleaning Tool.

（

）

3

Put the filters back together in the Dust Bin.

（

）

Tip: Clean the filter once a week and replace it every 2 months.

17

③. Rolling Brush

Remove brush cover, take out the rolling brush, clean the vacuuming aisle by a cloth. If the rolling brush has hairs winded,

please cut them down with the knife on cleaning tool.

�

�

�

�

18

④.Side Brush

Pull out the side brushes, use the knife on cleaning

⑤.Swivel Wheel

Clean the swivel wheel with a cloth.

tool to cut winded hairs, and then use cloth to clean it.

Tip: Please clean the rolling brush and side brushes once a week, change the side brush every 3 months, and change the

rolling brush every 6 months.

19

⑥.Cliff sensor

Use a dry cloth to clean cliff sensors to ensure the sensitivity.

20

5．Troubleshooting

No.

Problems

Causes

Solutions

Robot

cannot

be

1

charged

Charging Dock has no electricity.

Ensure the charging cord is plugged into the dock and wall outlet,

and the light on the Charging Dock is white.

The poor connection of the

charging contact points.

Clean the charging connection points on both Charging Dock and

bottom of the Robot with dry cloth.

Get stuck by objects.

Pick up objects like clothing, scraps of paper, power cords, and

fragile objects to avoid Robot stuck before it starts working.

Get stuck under furniture.

Robot’s slimmer body would work with most of the furniture but it

still probably gets stuck. Notice: the lowest height is 3 inches.

2

3

4

Robot gets stuck

Get stuck on carpet.

Robot is not suitable for use on long-pile carpet. Before using Robot

on a short-pile area rug with tasseled edges, please fold area rug’s

edges to prevent Robot from tangling.

Charging Dock has no electricity.

Ensure the charging cord is plugged into the dock and wall outlet,

and the light on the Charging Dock is white.

Robot cannot dock

The location of Charging Dock is

not correct.

Position the Charging Dock on a hard level surface (not on a

dark-colored surface or high-pile carpet) and refer to the suction“po-

sition the charging dock”in Manual.

Side brush falling

down

The side brush is not installed

correctly.

Put the side brush into the slot and hear a "click".

21

5

6

7

8

9

10

11

12

13

Left / right wheel

abnormal

The left / right wheel may be

entangled.

Check left / right wheel for entanglement and clean the side wheel.

Weak suction

The Dust Bin is full

Empty Dust Bin

Filter clogged or wet

Clean and dry the filter or replace it with a new one.

Cannot schedule

cleaning

The Main Power Switch on the

bottom of Robot is off

Turn on the Main Power Switch at the bottom of Robot.

Power is too low to start cleaning

Charge Robot.

The scheduled time have been set

incorrectly.

Set schedule cleaning according to APP Instruction.

Left/right side brush

abnormal

Left / right side brush may be

entangled.

Check whether the left/right side brush is entangled and clean the

side brush.

Rolling brush

Rolling Brush is stuck or

Check whether the rolling brush is entangled and clean the rolling

abnormal

entangled.

brush.

Robot suspended in

the air

Robot is suspended or stuck near

a cliff.

Please put the robot on the floor，or clean the cliff sensors

Camera abnormal

Camera is dirty.

Wipe camera with alcohol cotton ball gently.

Bumper abnormal

The bumper may get stuck.

Pat the left, middle and right sides of the infrared bumper to make it

flexible.

Dust Bin abnormal

Dust Bin maybe installed

incorrectly.

Install Dust Bin again.

22

A90 Robotic Vacuum Cleaner

Robot Vacuum

Charging Dock

325*325*80mm

Dimensions

170*137*95mm

Adapter Input Voltage

Rated Output

Rated Frequency

AC 100-240V

19V/600mA

50/60Hz

/

/

/

6．Specifications

Dimensions

Battery

Wireless connection

Rated Power

Rated Voltage

Charging Time

Working Hours

2600mAH

2.4GHz Wi-Fi

28W

14.4V

5H

120min

7.Amarey Customer Care

+86-400-676-0068

service_cn@iamarey.com

www.iamarey.cn

Manufacturer:

Address : Room 2208, Office Building 4, Chongwen Garden, No.1 Tangling Road, Fuguang Community,

Shenzhen Ankobot Robot Co.,Ltd

Taoyuan Street, NanShan District, ShenZhen

23

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any inte rference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interferenceto radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator and your body.



 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LABEL AND LOCATION

(Size: L5.4cm x 3.9cm) Label Location _____________________________________________________________________________________________________

 

 

Shenzhen Ankobot Robot Co.,Ltd Agent Authorization Company: Shenzhen Ankobot Robot Co.,Ltd Address: Room 2208, Office Building 4, Chongwen Garden, No.1 Tangling Road, Fuguang Community,Taoyuan Street, NanShan District, ShenZhen, China Product Name: Robotic Vacuum Cleaner Trade Mark: Amarey, Ankobot Model Number(s): A90+, A90, A92-JC, A92-CS FCC ID: 2ATCH-AK210522 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Huang ling Title:

Manager Company: Shenzhen Ankobot Robot Co.,Ltd Date: 2021-10-23

 

 

Shenzhen Ankobot Robot Co.,Ltd Room 2208, Office Building 4, Chongwen Garden, No.1 Tangling Road, Fuguang Community,Taoyuan Street, NanShan District, ShenZhen, China Series Models Description Date: 2021/10/23 Dear Sir/Madam, We, Shenzhen Ankobot Robot Co.,Ltd Hereby declares the following statement for EU/US/MIC certificate, PCB board, Schematic, Hardware version, Software version, structure and internal photos are same except for the models name; named differently due to marketing purposes. Product name:

Robotic Vacuum Cleaner Model no.:

A90+, A90, A92-JC, A92-CS Sincerely yours Name / Title: Huang ling / Manager Company: Shenzhen Ankobot Robot Co.,Ltd Address: Room 2208, Office Building 4, Chongwen Garden, No.1 Tangling Road, Fuguang Community,Taoyuan Street, NanShan District, ShenZhen, China Phone: +8613612818384 Fax:/

E-Mail: anna.huang@ankobot.com

 

 

Shenzhen Ankobot Robot Co.,Ltd Room 2208, Office Building 4, Chongwen Garden, No.1 Tangling Road, Fuguang Community,Taoyuan Street, NanShan District, ShenZhen, China Class II Permissive Change Letter FCC ID: 2ATCH-AK210522 Date: Oct. 23, 2021 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Request Class II Permissive Change for FCC ID: 2ATCH-AK210522 To Whom It May Concern, The purpose of this letter is request a Class II Permissive Change for FCC ID: 2ATCH-

AK210522, original grant date: 08/19/2021;

Applicant: Shenzhen Ankobot Robot Co.,Ltd The main change filed under this application is the main control IC and battery were changed, meet KDB 178919 D01: Hardware changes as follows;

Item Description Yes / No 1 Hardware changes Yes 2 3 4 5 There is no increase in the output power rating (unless such exceptions are permitted by rules or KDB publications see V) G)). The Equipment Class remains the same. (Changes that require a new Equipment Class code require a new grant of certification (FCC ID), except for SDR approvals.) RF exposure changes must be addressed There are no other changes to the device that indicate a need for a new FCC ID. Yes Yes Yes Answer from applicant Only the main control IC and battery were changed. New main control IC: GD32F103 Original main control IC:

AT32F403AVCT7 New battery: N157-004 Original battery: T-451P-C Original power was 0.0789 W for RoLa, new power is 0.0719 W for RoLa. Same as original application;

Equipment Class remains is DTS. Update revised RF exposure report;

Yes No any change. Shenzhen Ankobot Robot Co.,Ltd Room 2208, Office Building 4, Chongwen Garden, No.1 Tangling Road, Fuguang Community,Taoyuan Street, NanShan District, ShenZhen, China I attest that such change will affect the RF function out of the grant conditions, just need measured following items as follows;

Maximum Conducted Output Power Radiated Spurious Emissions Emissions at Restricted Band AC Conducted Emissions RF Exposure Evaluation Should you have any questions or comments regarding this matter, please have my best attention. Sincerely,

(Signed) Name / Title: Huang ling / Manager Company: Shenzhen Ankobot Robot Co.,Ltd Address: Room 2208, Office Building 4, Chongwen Garden, No.1 Tangling Road, Fuguang Community,Taoyuan Street, NanShan District, ShenZhen, China Phone: +8613612818384 Fax:/

E-Mail: anna.huang@ankobot.com

 

 

Shenzhen Ankobot Robot Co.,Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-10-23 Subject; Request for Confidentiality FCC ID: 2ATCH-AK210522 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description BOM Software Security Requirements In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name / Title: Huang ling / Manager Company: Shenzhen Ankobot Robot Co.,Ltd Address: Room 2208, Office Building 4, Chongwen Garden, No.1 Tangling Road, Fuguang Community,Taoyuan Street, NanShan District, ShenZhen, China Phone: +8613612818384 Fax:/

E-Mail: anna.huang@ankobot.com

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Shenzhen Ankobot Robot Co.,Ltd

WIFI Channel 12 and 13 Declaration Letter

We declare the equipment identified below with regards to Channel 12 and 13

capabilities for

FCC ID: 2ATCH-AK210522

Declaration

Product hardware does not have the capability to operate on

Channel 12 and 13.

Product hardware has the capability to operate on Channel 12

and 13. However, these two channels will be disabled via

software and will not be accessible to user.

Product hardware has the capability to operate on Channel 12

and 13. However, all the operated channels can’t be changed in

the RF parameter via software. All channels have complied with

all of the requirements sets out in FCC Part 15.247.

Product hardware has the capability to operate on WiFi Channel

12 and 13, and meets the requirements of KDB 594280 D01

v02r01. Please note:

1.) By default, this device operates in a mode that is

compliant with the U.S. requirements.

2.) This device will also use supplemental information such as

geo-location data to determine that it is operating outside

the U.S., if necessary, to change its power. Such

supplemental data will be derived from the following:

Global Navigation Satellite System (GNSS)7 sensors in the

device

Mobile Country Code (MCC),8 or MCC with a Mobile Network

code (MNC), received from a CMRS9 carrier and received

directly by a receiver on the device

Country information derived from multiple adjacent access

points (for example using IEEE Std 802.11d provisions) may be

permitted on case-by-case basis

Other suitable geo-location data based on IP addresses or other

reliable source.

Name / Title: Huang ling / Manager

Page 1 of 1

Rev.2.0

Signature:

Phone: +8613612818384

Email: anna.huang@ankobot.com

Date: 2021-08-17

Page 2 of 1

Rev.2.0