User Manual
Features:
● Dual RF system
● For triggering and remote control of Flash
● Dual RF system, One system can receive and transmit, and the working
frequency channels between 2404~2480 MHz,the other system only can working on receive.
and the working frequency channel is:315MHZ-435MHZ.
● Demodulation mode is MSK(2.4GHz) and ASK and MSK and GFSK(315MHZ-435MHz),
● Up to 100 m range outside
● Up to 50 m range inside
● Modulation mode is MSK,
● Common RX and TX interface
● 250kbps, 1 and 2Mbps air data rate
● 1.9 to 3.6V supply range
● Working Temperature: -10℃~+40℃
● Working Humidity: 35﹪~95﹪RH
● Antenna: PCB antenna(2.4GHz) and Helix antenna(315MHz-435MHz)
Channel List for 2.4G system:
Mainly, will have below Channels:
This RF module will be used on different device, the channel list also will have difference,
CH1:2.404000212 GHZ
CH2: 2.412000636 GHZ
CH3: 2.417000901 GHZ
CH4: 2.422001166 GHZ
CH5: 2.427001431 GHZ
CH6: 2.447002491 GHZ
CH7: 2.454002862 GHZ
CH8: 2.479337538 GHZ
Others channel(MHZ):
2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420
2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437
2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454
2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471
2472 2473 2474 2475 2476 2477 2478 2479 2480
Channel List for 3XXMHz system:
315MHz-435MHZ
Radiation Exposure Statement
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator and your body.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
-- Consult the dealer or an experienced radio/TV technician for help.
connected.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any inte rference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
INDUSTRY CANADA STATEMENTS
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner
avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention
des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance
isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l'intensité nécessaire à l'établissement
d'une communication satisfaisante.
The ISED certification label of a module shall be clearly visible at all times when installed in
the host product; otherwise, the host product must be labelled to display the ISED certification
number for the module, preceded by the word "contains" or similar wording expressing the same
meaning, as follows: contains IC:25192-RF8.
As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module installed.
Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following" Contains FCC ID: 2AEJW-RF8"
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the
user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01
2.2 List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
2.3 Specific operational use conditions
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different
operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for
the installation method in end system.
2.4 Limited module procedures
This module is Limited single modular without shielding, host manufacturer have to consult with module manufacturer for the module
limiting conditions when integrate the module in the host. module manufacturer should reviews detailed test data or host designs prior
to giving the host manufacturer approval.
2.5 Trace antenna designs
Not applicable
2.6 RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
2.7 Antennas
The module is not designed for multiple antenna applications and should not be used to transmit simultaneously with any other
transmitter. The module is only certified to use the integrated PCB antenna.Antenna Description:PCB Antenna antenna,Max
Gain:3.0dBi.
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following" Contains FCC ID:2AEJW-RF8".
2.9 Information on test modes and additional testing requirements
Host manufacturer which install this modular with limit modular approval should perform the test of radiated emission and spurious
emission according t o FCC part 15C:15.247 and 15.209 requirement, only if the test result comply with FCC part 15.247 and 15.209
requirement, then the host can be sold legally.
2.10 Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the
system such as Part 15B.
Note:The module will later be used on the flash and flashers and the associated remote control equipment(only for Shenzhen Aodelan
Technology Co., Ltd.)