all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 377.49 KiB | October 05 2015 | |||
1 | Cover Letter(s) | October 05 2015 | ||||||
1 | External Photos | October 05 2015 | ||||||
1 | ID Label/Location Info | October 05 2015 | ||||||
1 | Internal Photos | October 05 2015 | ||||||
1 | RF Exposure Info | October 05 2015 | ||||||
1 | Test Report | October 05 2015 | ||||||
1 | Test Setup Photos | October 05 2015 |
1 | Users Manual | Users Manual | 377.49 KiB | October 05 2015 |
environment. paper. period. E3+ Wireless Trigger for Canon Thank you for purchasing an Aodelan Product Note: Before using the E3 + Wireless Trigger for Canon, please read this instruction manual carefully, while also referring to the instruction manuals of your camera, flash and other relevant devices. Warnings 1. This product is a precise electronic instrument. Do not expose to damp environments or dust. 2. Please shut down the power of all devices when installing the wireless trigger. 3. Do not drop or crush. 4. Do not use the wireless trigger at flammable, explosive or high temperature 5. Do not use harsh chemicals or solvents to clean the body. Use a soft cloth or lens 6. Remove batteries from the wireless trigger if not being used for an extended 7. Interference: The E3+ wireless trigger transmits radio signals at 2.4GHz. Its performance can be affected by electrical current, magnetic fields, radio signals, wireless routers, cellular phones, and other electronic devices. Environmental objects, such as large buildings or walls, trees, fences, or cars can also affect transmission performance. If your wireless trigger can location slightly. t be triggered, move its FCC Interference Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. E3+ Wireless Trigger for Canon/Transmitter E3+ transmitter is a transmitter for wireless flash shooting. It can control up to 5 groups (15units) of Canon Speedlites that have a wireless multiple flash shooting function using radio transmission, as well as non-wireless Canon ETTL Speedlites by using E3 + receiver. The transmitter supports multiple flash modes and shooting approaches including E-TTL II/E-TTL, Manual, MULTI, Ext.A and Linked Shooting, catering to the diversification of photography lighting demands. Table of Contents I. II. III. IV. Wireless Flash Shooting: Radio Transmission Parts Preparation Before Use The LCD Display 1. Wireless Flash Setting 2. ETTL: Fully Automatic Wireless Flash Shooting 3. Using Fully Automatic Wireless Flash 4. ETTL: Wireless Multiple Flash Shooting with Flash Ratio 5. M:Wireless Multiple Flash Shooting with Manual Flash Output 6. Multi:
7. Gr: Shooting with a Different Flash Mode for Each Group 8. Linked Shooting Setting Transmitter Functions with Camera Operations Customizing the Transmitter 1.C.Fn: Setting Custom Functions 2.P.Fn: Setting Personal Functions VII. Technical Specification VII. Trouble Shooting Guide V. VI.
>: Select/Set button
>: Select dial I.Parts 1.<LINK> indication light: Radio transmission confirmation lamp 2.LCD panel 3.Function Button 3 4. Function Button 2 5. Function Button 1 6.<MODE>: Flash mode button 7.< >: Charge lamp/Test flash button 8.<
9.<
10.Mounting foot lock lever 11.Battery compartment cover 12.Function button 4 13. <
14.Power button 15.Flash exposure confirmation lamp 16.Lock-release button 17.USB port 18.Remote release terminal 19.Contacts 20.Mounting foot 21.Locking pin 22.AF assist light
>: Linked shooting button II. Preparation before use Installing the batteries 1. Press the battery compartment cover and slide it down as shown to open the battery cover. (Picture 1) 2. Insert the batteries as shown. Make sure the + and-battery contacts are correctly oriented as shown. (Note:
Please use 2 pieces of AA alkaline batteries or AA type NI-MH batteries.
(Picture 2) 3. Replace the battery cover and push back into the locked position. Attaching and Detaching the E3+ transmitter Attaching the E3+ transmitter to the camera hot shoe 1. Turn off the camera and E3+
transmitter 2. Align the E3+ transmitter hot shoe with cameras hot shoe mount. 3. Slide the E3+ transmitter all the way into the cameras hot shoe mount. 4. Lock the E3+ transmitter by sliding the mounting foot lock lever to the right until the lock lever clicks in place.(See picture 3) Detaching the E3+ Transmitter 1. Lock release: press the lock-release button while slide the lock lever all the way back to the left.see picture 4 2. Slide the E3+ transmitter out of cameras hot shoe mount. 2 1 Turn On/Off the E3+ transmitter 1. Turn On: Press and hold the power button until MENU interface is displayed on screen. 2. Turn off: Press and hold the power button until the LCD screen goes blank. Note: When is displayed, please replace the batteries with new ones. USB port The firmware of E3 + transmitter can be upgraded via the USB port, so as to adjust its parameter and extend its compatibility with cameras to come in the future. 1.1 Connect the USB cable to the computer and the other end of the USB cable to E3+ transmitters USB port. A mobile device icon will be displayed on the computer when successfully connected. 1.2 Double click to start the upgrade software. The upgrade software can be used to check version info, and upgrade the Base software, RF software and Icon. Click "Version" icon, the current version information of the connected E3 + transmitter will be displayed in the software window. Click "Base software" icon, locate and double click on the FDS file from the pop-out window. Then it starts loading the new firmware. Click "RF software" icon, locate and double click on the RFC file from the pop-out window. Then it starts loading the new firmware. Click "Icon" icon, locate and double click on the FIF file from the pop-out window. Then it starts loading the new firmware. 1.3 The status of the upgrade will be displayed in the process bar. When completed, an Updata OKwill be displayed at the bottom of the upgrade software window, and a Download OK will be displayed on the transmitter completion, disconnect the USB cable and restart the E3+ transmitter. Note:
Please ensure stable power supply when attempting to upgrade the E3 Loss of computer power during the upgrade process could fail the upgrading. Check Version info on E3+ transmitter You can check the present version information on E3 + transmitter: while pressing the power button to turn on the transmitter, press the flash <MODE> button simultaneously until the version info is displayed on the LCD screen.
<>: Charge Lamp/Test Flash Button 1. The charge lamp lights when the wireless shooting (slave) is ready. 2. During wireless shooting, master unit s charge up will be lit when all slave units s LCD screen. Upon
+ transmitter.. 3. During wireless shooting, you can press the transmitters charge lamp (test flash are fully charged. button to fire a test flash. Remote Release from Slave Unit When performing wireless shooting, E3 + transmitter supports remote release (remote control shooting) from a flash set or E3 + receiver as a slave unit. For operations, see the flash or E3+ receivers instruction manual. Note When using the remote release function, the slave unit camera might need a shutter release cable(available separately) depending on the camera models. 1) EOS digital cameras since 2012 do not need to use shutter release cable. 2) EOS cameras before 2012, which are compatible with E-TTL II/E-TTL autoflash and come with N3 type remote terminal EOS, shutter release cable will be needed for linked shooting. Test Flash from a slave unit You can fire a test flash from a flash set as a slave unit. For operations, see the flash s instruction manual. Note: When two or more units are set to master, the unit with the <LINK> lamp lit in green is the one that fires. Modeling Flash 1. Modeling Flash from a Master Unit When the camera s dept-of-view preview button is pressed, the flash will fire continuously for 1 sec. This is called the modeling flash. It enables you to see the shadow effects of the flash on the subject and the lighting balance. Besides, you can also fire the modeling flash by pressing the charge lamp/test flash button on E3 transmitter (the operation required to be enabled in advance by setting C.Fn 02). 2. Modeling Flash from a Slave Unit With EOS digital cameras released since 2012, you can fire the modeling flash from a flash set as a slave unit. For the operations, see the flashs instruction manual. AF assist light In low light/contrast situation, the E3 + transmitters built-in Auto Focus Assist Light will illuminate to assist with AF. The AF Assist Light on the front of the transmitter will project a focusing target on the subject. As laser light, the AF assist light has the advantages of better directionality, less decay and better assist performance compared with LED type AF assist light. You can choose to enable or disable the AF assist light by setting P. Fn 08. Note: The laser AF assist light is safe with optical power less than 5mW. However, please still avoid pointing the light at human eyes. Memory Function
+
Firing group Multi Stroboscopic Flash Frequency Multi Stroboscopic Flash Number Up to 5 firing groups A BCDEat Gr mode 1-500Hz 1-100times, based on the frequency and flash output 10 11 12. LCD Display E3+ transmitter s LCD display comes with five modes:
ETTLMMULTIGr and LINKED SHOT. You can cycle through ETTLMMULTIGr by pressing <MODE> button. And by pressing and holding <
>button, you can switch the LCD to display LINKED SHOT. Different display settings come to perform different flash modes. Find details about the five flash modes as following 1. ETTL/ETTL II autoflash
: High Speed Sync;
: Sync speed warning
: Beep E-TTL/E-TTL autoflash
: Flash Exposure Compensation and Flash Exposure Compensation amount RATIO:
RATIO OFF, RATIO A:B, RATIO A:B C Firing Group Flash ratio sequence Flash exposure level
: FEB and FEB
: Radio transmission wireless shooting Ch: Channel AUTO: Channel Automatic setting
: Custom Functions
: Slave flash ready Personal Functions
: Master 2. Manual Flash M: Manual Flash Manual Flash Output 3. Stroboscopic Flash MULTI: Multi (Stroboscopic) flash Flash frequency Number of flashes 4. Group Firing Gr: Firing Group Three flash modes optional: ETTLMExt.A 5. Linked Shooting LINKED SHOT: Linked Shooting Note: 1) The display will show only the settings currently applied. 2) The functions displayed above function buttons 1 to 4, such as MASTER, Master unit;
SLAVE, Slave unit;
and
, change according to the settings status. 3) When a button or dial is operated, the LCD panel illuminates. IV. Wireless Flash Shooting: Radio Transmission Note:
The transmitter attached to the camera is called the master unit, and a flash that is wirelessly controlled is called the slave unit. When the camera s shooting mode is set to fully automatic mode or an Image Zone mode, the operations below are not available. Please set the camera s shooting mode to P/Tv/Av/M/BCreative Zone mode. Wireless Flash Shooting Using a transmitter and Canon Speedlites compatible with radio transmission wireless shooting makes it easy to shoot with advanced wireless multiple flash lighting, in the same way as normal E-TTL/E-TTL auto flash shooting. The settings of the transmitter attached to the camera master are automatically reflected on the flash that is wirelessly controlled (slave). Therefore, you do not need to operate the slave unit while shooting. You can then perform wireless E-TTL II/ETTL autoflash shooting just by setting the master unit to ETTL mode. You can choose to perform autoflash shooting using one slave unit only, or perform wireless multiple flash shooting using two or more(up to 15) slave units. The slave units can be speedlites that is compatible with radio transmission wireless shooting and set on slave mode, and also, by using with E3 ETTL flashes that are incompatible with the radio transmission wireless function.
+ receiver, other Canon Master Unit E3+Transmitter Slave Unit Canon Speedlites that have a wireless flash shooting function using radio transmission, like 600EX-RT Slave mode. E3+receiver+Canon ETTL FlashNon-wireless mode Note:
1) When using E3 +receiver as slave unit, restrictions will apply to parts of its functions. And parts of the operations would also be different. For details, see the instruction manual of E3+receiver 2) When performing radio transmission wireless flash shooting, restrictions may apply to the flash mode, maximum flash sync speed (referred to below as the sync speed) and high-speed sync function, depending on the camera that you use. Wireless Settings flash is displayed. To perform wireless shooting, set the E3+ transmittermaster unitand flashslave unit with the following procedure. 1. Master unit setting: Check that 2. Slave unit setting: For the slave unit setting, see the flash or receiver s instruction manual. 3. Transmission Channel/Wireless Radio ID Settings: To avoid interference with wireless multiple flash systems using radio transmission that are used by other photographers or with other devices that use radio waves (wireless), you can change the transmission channel and wireless radio ID. Use the following procedures to set the master unit wireless radio ID. Set the same channel and ID for both the master unit and slave unit. For the slave unit settings, see the flashs instruction manual. s transmission channel and 1. Press function button 4 until 2. Set a channel: press function button 1 corresponding is displayed.
, turn <
to Auto, and press <
> to select from Ch. 1-15 or
> button to finish the setting. 3. Set wireless radio ID: press function button 2 corresponding to digit to be set and press <
, turn <
> to select the
> button. Again turn <
> to select a number from 0-9, and press the <
> button. 4. Repeat step 4 to set the four ID digits one by one. Press function button 4 for corresponding to to return to the shooting-ready state. 5. When the transmission between the master unit and slave unit is established, the <LINK> lamp lights green. 4. Scanning the Master Unit Transmission Channels to Set E3+ transmitter is able to scan the radio reception status and set the master unit s transmission channel automatically or manually. When the channel is set to AUTO, the channel with the best reception signal is automatically set. When setting the channel manually, you can set the transmission channel again while referring to the scan results.
, and then function
. The channel is reset to one 1. Scanning while AUTO is set:
Press function button 4 to display button 3 corresponding to with a good reception signal. 2. Scanning while Ch.1 to 15 is set:
Press function button 4 to display button 3 corresponding to displayed in a graph. The higher the peak of the channel in the graph, the better the radio reception signal. Turn<
return to shooting-ready state.
, and then function
. The radio reception status is
>to select from Ch.1 to 15, and press<
>button to The color of <LINK>lamp changes depending on the transmission status of the master unit and the slave unit. Color Green Red Status Lit Lit Blinking Description Transmission OK -
No connected Too many units Error Action Check the channel and ID Master Units + slave units = 16units or less Turn the power off and on again Note: 1).If the transmission channels of the master unit and slave unit are different, the slave unit does not fire. Set both to the same number, or set both to AUTO. 2).If the wireless radio IDs of the master unit and slave unit are different, the slave unit does not fire. ETTL: Fully Automatic Wireless Flash Shooting E3+ transmitter attached to the camera (master) and a wirelessly controlled flash
(slave) can perform fully automatic wireless shooting. 1. Autoflash Shooting Using One Slave Unit 1.1 Set the flash as the slave unit: For the slave unit setting, see the flash or the E3+receivers instruction manual. Set A, B or C as the firing group. If set to D or E, the flash does not fire. 1.2 Check the channel and ID: If the channels and IDs of the master unit and slave unit are different, set them to exactly the same number. 1.3 Position the camera and the slave unit within the range of wireless radio transmission. 1.4 Set the flash mode to <ETTL>: Press the <MODE> button on master and set the flash mode to <ETTL>.The slave unit is set automatically to<ETTL> during shooting via the control form the master unit. For slave units that use E3+ receiver, flashes on the receiver need not to set to wireless slave mode, but the need to be set to ETTL mode manually during shooting. 1.5 Check the transmission status and that the flash is ready:
Check that the <LINK>lamp lights green;
When the flash that is set to wireless slave mode is ready, the AF-assist beam emitter blinks at 1-second intervals;
Check that the < > slave flash-ready icon is lit on the master units LCD panel;
When the recycling of all the flash units is completed, the master units lights on. 1.6 Check the operation: Press the master unit s test flash button (charge lamp). The slave unit flash will fire. If no, check that it is placed within the operation range. 1.7 Take the picture: Set the camera and take the picture, in the same way as with normal flash shooting. If a standard flash exposure was obtained, the flash exposure confirmation lamp lights up (blue) for 2 sec. charge lamp 2. Autoflash Shooting Using Multiple Slave Unit When you need more flash output or you want to perform lighting more easily, you can increase the number of slave units and fire them as a single flash. To add slave units, use the same procedure as Autoflash Shooting Using One Slave Unit . Set A, B or C as the firing group. The flash will not fire if it is set to D or E. When the number of the slave units is increased, automatic control is performed to fire all flashes at the same flash output and ensure that the total flash output results in standard exposure. Using Fully Automatic Wireless Flash Flash exposure compensation and other settings set on the E3+ transmitter (master unit) will be automatically set in the flash (slave). You dont need to operate the slave unit. 1. Flash Exposure Compensation In the same way as normal exposure compensation, you can set exposure compensation for flash. The flash exposure compensation amount can be set up to 3 stops in 1/3-stop increments. 1. Press function button 4 until 2. Press function button 2 corresponding to is displayed.
, is displayed and flash compensation amount is highlighted. 3. Set the flash compensation amount: turn<
the flash compensation amount, and press <
> to set
>button. 4. 0.3 indicates 1/3 stops, and0.7indicates 2/3 stops 5. To cancel flash exposure compensation, return the compensation amount to 0. Note:
1. By setting C.Fn13, you can choose to set the flash compensation amount by
> only, without operating function button 2
. turning <
2. If the camera s exposure compensation is set to 1/2-stop increments, flash exposure compensation will be up to stops in 1/2-stop increments. 2.FEB With FEB (Flash Exposure Bracketing) function, you can take three shots while automatically changing the flash output. The settable range is up to 3 stops in 1/3-stop increments. is displayed.
, 1. Press function button 4 until 2. Press function button 3 corresponding to is displayed and the FEB level display is highlighted. 3. Set the FEB level: turn<
> to set FEB level and press <
4.0.3indicates 1/3 stops, and0.7indicates 2/3 stops. 5. When used together with flash exposure, FEB shooting is performed based on the flash exposure compensation amount.
> button. Note:
1You can choose whether or not to cancel FEB automatically after shooting three shots with FEB by setting C.Fn03. 2You can change the order of FEB sequence by setting C.Fn04. 3. High-speed Sync With the high-speed sync function, the flash can synchronize with all shutter speeds. This is convenient when you want to use aperture-priority AE for fill-flash portraits of a subject. High-speed sync function is available for EOS digital cameras since 2012 only. 1. Press function button 4 until 2. Press function button 2 corresponding to will be displayed on the screen. Check if the view finder. is displayed.
, is lit in 3. Press function button 2 will disable
. 4. FEL: FE Lock FE (Flash Exposure) lock locks the correct flash exposure setting for any part of the scene. Perform FE lock by operating the camera. For the operation, see the camera and flashs instruction manual. 5. About Master Units You can use two or more master units (master units + slave units = maximum of 16 units). By preparing multiple cameras with master units attached, you can shoot by changing cameras while keeping the same lighting (slave units). Note that when using two or more master units, the color of the <LINK> lamp varies depending on the order in which the power was turned on. The first master (main master) is green and the second subsequent masters (sub masters) are orange. ETTL: Wireless Multiple Flash Shooting with Flash Ratio 1. Autoflash shooting with Two Slave Groups You can divide the slave units into two firing groups A and B, and adjust the lighting balance (flash ratio) for shooting. The exposure is controlled automatically so that the total flash output of firing group A and group B results in the standard exposure. 1.1 Set the firing group of the slave units Operate and set the slave unit group one by one. Set one unit to <A>, and set the other to <B>. For the slave unit settings, see the flash or receivers instruction manual. 1.2 Set the ratio mode: Press the master unit Press function button corresponding to s function button 4 to display to set to <
>. 1.3 Set the flash ratio: Press function button 3 corresponding to press the function button 3 while it is corresponding to flash ratio and press<
to return to shooting-ready state.
>button. Press function button 4 corresponding to
, and again
>to set the
, turn<
1.5 Take the picture: the slave unit flash at the set flash ratio. A B Autoflash Shooting with Thee Slave Groups 2. You can add firing group C to firing groups A and B. C is convenient to set lighting so as to eliminate the subject s shadow. The setting method is the same as Autoflash Shooting with Two Slave Groups
. A/B 1.Press <Mode> button to set the flash mode to
<M>
2.Set the number of firing group:
is displayed, press function button 2 While corresponding to to set the groups to fire. The setting changes as follows each time pressing the button: ALL A/B/C 3.Select a firing group: Press function button 3 corresponding to
> to select the group for which you want to set the flash output, and press <
4.Set the flash output: Press function button 3 corresponding to <* >, turn<
output and press <
to set the output of all groups 5.Take the picture: each group fires at the set flash output
>to set the flash
>button. Repeat step 3and 4
>button.
, turn<
MULTI: Stroboscopic Flash Stroboscopic flash is an advanced manual flash shooting method. When using stroboscopic flash with a slow shutter speed, you can shoot multiple successive movements within a single picture, similar to stop-motion pictures. In stroboscopic flash, set the flash output, number of flashes, and flash frequency (number of flashes per second = HZ). 1. Press master units <MODE>button to set the flash mode to<MULTI>. 2. Set the number of firing groups and flash output for each group by referring to manual flash on the preceding page. 3. Set the flash frequency and number of flashes:
when corresponding to number of flashes and press<
is displayed, press function button 2
> to set the
>button;
, turn<
Press function button 3 corresponding to turn<
> to set the flash frequency and press<
,
>button. Note 1. High speed sync function is not available when using stroboscopic flash. 2. E3+ receiver does not support MULTI mode. When master unit is set to MULTI mode, the slave unit that uses E3+ receiver does not fire. Gr: Shooting with a Different Flash Mode for Each Group When using an EOS digital camera released since 2012, you can shoot with a different flash mode set for each firing group, with up to 5 groupsA/B/C/D/E. The flash modes that can be set are E -TTL/E-TTL autoflash, Manual flash and Auto external flash metering. When the flash mode is or , exposure is controlled to result in standard exposure for the main subject as a single group. The function is for advanced users. 1. Set the flash mode to <Gr>
Press <MODE> button on master unit to set the flash mode to <Gr>. 2. Set the firing group on the slave units Operate and set the slave units one by one, and set a firing groupA/B/C/D/Efor all the slave units. For slave unit settings, see the flash or wireless receiver s instruction manual. 3. Set the flash mode Set the flash mode of each firing group by operating the master unit. While
<
Press function button 2 corresponding to <*Mode> to select the flash mode of the selected group from <ETTL>, <M>and<Ext.A>. To turn off the firing of the selected group, press function button 1 corresponding to is displayed, press function button corresponding to
>to set the group. and turn and set it to <OFF>. Repeat step 3 to set the flash mode.
> to set the flash function corresponding to the flash mode, and press<
4. Set the flash output or flash exposure compensation amount While a firing group is selected, press function button 3 corresponding to <* >, turn
<
>
button. When using the <M> mode, set the flash output. When using the <ETTL>or<Ext.A>, set the flash exposure compensation amount as required. Press function button corresponding to exposure compensation can be set for all groups. Repeat step 4 to set the flash function of all groups. is displayed, flash when 5. Take the picture: each slave units fires in the flash mode set for each group. Linked Shooting Linked shooting is a function that automatically releases the shutter of a slave unit camera by linking it to a master unit camera. You can shoot with linked shooting for up to 16 units, including both master units and slave units. This is convenient when you want to shoot a subject from multiple angles at the same time. To shoot with linked shooting, attach E3 + transmitter, and canon flash that supports radio transmission wireless shooting or the canon ST-E3-RT Speedlite transmitter to the camera. Slave Slave Master Linked shooting setting 1. Set to linked shooting mode Press and hold linked shooting button until shooting mode s Slave unit is set; Press linked shooting button again to set Master unit of linked shooting mode. is displayed. Linked
, turn <
2. Set the channel and ID
> to Set the channel by pressing function button 2 corresponding to select the channel and press <
>button. You also choose to scan the radio reception status and set the master unit s transmission channel automatically or manually. For operation please refer to preceding wireless setting section. Set wireless radio ID: press function button 3 corresponding to select the digit to be set, and press <
> button. Again turn <
from 0-9, and press the <
by one. Press function button 4 for corresponding to shooting-ready state. 3. Set the cameras shooting functions 4. Set all the transmitters Repeat steps 1to3 and set all the transmitters to Master unit or Slave unit in the
> to
> to select a number
> button. Repeat the procedure to set the 4 ID digits one to return to the
, turn <
linked shooting mode. Set the Speedlites used in linked shooting in the same way. When pressing linked shooting button to change the setting of a unit from Slave unit to Master Unit, the other transmitter (or Speedlites) that were set to Master Unit until then automatically switch to Slave unit. 5. Set up the slave unit cameras Check that the <LINK> lamp of the slave unit lights green and place all the slave units within master units the radio transmission range. 6. Take the pictures Check that the <LINK> lamp of the master unit lights green and take the picture. The slave unit cameras are released in coordination with the master unit camera. After shooting with linked shooting, the <LINK> lamp of slave unit briefly lights orange. 7. Press function button 1 corresponding to shutter of all slave unit cameras. Noted:
1.When using the linked shooting function, the slave unit camera might need a shutter release cable(available separately) depending on the camera models. 3) EOS digital cameras since 2012 do not need to use shutter release cable. 4) EOS cameras before 2012, which are compatible with E-TTL II/E-TTL autoflash and come with N3 type remote terminal EOS, shutter release cable will be needed for linked shooting. 2. Shooting with manual focus is recommended for the slave unit cameras. If focus cannot be achieved with autofocus, linked shooting is not possible with the corresponding slave unit cameras. on master unit will release the V. Setting Transmitter Functions with Camera Operations Note: When the camera s shooting mode is set to fully automatic mode or an Image Zone mode, the operations below are not available. Please set the camera mode to P/Tv/Av/M/BCreative Zone mode. When using EOS digital camera released since 2007, you can set flash functions, transmitter functions or Custom Functions from the camera s menu screen. For the camera operations, see the cameras instruction manual. (Examples displayed are EOS 6D menu screen) 1. E3+ Transmitter Function Setting s shooting 1.Select [External Speedlite control]or[Flash control]. 2.Select[Flash function settings]or[External flash func. setting], the screen changes to the externalflash function settings screen 3.Select an item and set the function. The setting screen varies depending on the camera 2.Settings Available in [Flash function settings]
Enable wireless flash Flash firing shooting
[Enable]
E-TTLfl ash metering
[Disable] Disable wireless flash shooting For normal exposures
[Evaluati ve]
[Average] Flash exposure will be averaged for the entire scene metered by the camera. Flash exposure compensation may be necessary depending on the scene. This setting is for advanced users. You can set the flash sync speed when performing wireless flash shooting in aperture-priority AE(Av) mode Flash synchroniz ation speed in AV mode Flash mode E-TTL/Manual flash/ MULTI flash
/Individual group control 1st curtain / High-speed synchronization Shutter synchroniz ation Flash exposure compensati on FEB Wireless Users can set the exposure compensation for flash up to increments. 3 stops in 1/3-stop Users can take three shots while automatically changing the flash output, with settable range up to 3 stops in 1/3-stop increments. Radio transmission wireless flash flash functions setting Clear Speedlite function settings shooting is set automatically.(*For EOS digital camera released since 2012). You can restore E3+ transmitter to their default settings 3. Transmitter Custom Function Settings The displayed contents vary depending on the camera. If C.Fn-20 and 22 are not displayed, set them by operating the transmitter. 1. Select[Flash C.Fn settings]or[External flash 2. Select the Custom Function number and set C.Fn setting]
function 3. To clear all the Custom Function settings, select
[Clear all Speedlite C.Fn s] or [Clear ext. flash C.Fn set] in step 1. Note: [Auto power off] under [Flash C.Fn settings] is corresponding to E3+transmitters C.Fn 01: Auto IDLE. You can enable or disable Auto IDLE for E3 +transmitter by operating the Camera menu option. VI. Customizing the Transmitter E3+ Transmitter supports Custom functionC.Fnand Personal FunctionP.Fnsetting. You can customize the transmitter features to suit your shooting preferences with custom functions and personal functions. Note that the personal functions are customizable functions unique to the E3+ transmitter. Note: When the camera s shooting mode is set to fully automatic mode or an Image Zone mode, the operations below are not available. Please set the camera mode to P/Tv/Av/M/BCreative Zone mode. 1. C.Fn: Setting custom functions 1.Press function button 4 until is displayed on the screen. s shooting until Custom Function
>button to display the
>to select an item(number) to set, and press<
2.Press and hold the function button 1 corresponding to screen is displayed. 3.Turn<
setting. 4.Turn<
>to select the setting, and press<
5.Press function button 4 corresponding to 6.To restore all the default settings of custom function, press function button 2 corresponding to cancel the operation, press function button 4 corresponding to Custom Functions Chart
, and press function button 1 corresponding to
. to return to previous state .
> button to confirm the selection
.To Functions Setting No. Setting and descriptions Custom Function No.
: Auto IDLE
:
Modeling flash
: FEB auto cancel
: FEB sequence
: Test firing with autoflash Enable Auto IDLE when the E3+
transmitter is not operated for 5min., Disable Auto IDLE when the E3+
transmitter is not operated for 5min., Press the cameras depth-of-field preview button to fire the modeling flash Press E3+ transmitters test flash button to fire the modeling flash Press the cameras depth-of-field preview button or E3+ transmitters test flash button to fire the modeling flash Disable the modeling flash Enable: Set to automatically cancel FEB after shooting three shots with FEB Disable: Set not to automatically cancel FEB after shooting three shots with FEB Set the order of FEB sequence as following:
0: Standard exposure
- : Decreased exposuredarker
+ : Increased exposurebrighter Set the order of FEB sequence as following:
- : Decreased exposuredarker 0: Standard exposure
+ : Increased exposurebrighter Set the flash output as 1/32 when firing the test flash in E-TTL autoflash Set the flash output as 1/1 when firing the
/E-TTL
: Flash exposure metering setting
: Beep
: LCD panel illumination test flash in E-TTL/E-TTL autoflash Turn<
>and press button function corresponding to exposure compensation Turn<
exposure compensation without pressing
>directly to perform flash to perform flash button. Disable beep to sound on E3+ transmitter when the slave unit is fully charged Enable a beep to sound on E3+
transmitter when the slave unit is fully charged When a button or dial is operated, the LCD panel illumination go on for 12 sec. Disable LCD panel illumination When a button or dial is operated, the LCD panel illuminates and keeps always on. 2. P.Fn: Setting personal functions 1. When Custom Function screen is displayed, press function button 1 corresponding to 2. Set the personal function in the same way as step 3 and 4 for the custom function. 3. To restore all the default setting of personal function, set it in the same way as step 6 for custom function. to display Personal Function screen. Personal Functions Chart Personal Function Functions No. Setting No. Setting and descriptions
: LCD panel display contrast
:LCD panel illumination color: Master
:LCD You can adjust the contrast of the LCD panel in 5 levels. When the E3 + transmitter is set as master unit radio transmission wireless shooting, linked shooting, select green as color of the LCD panel illumination. When the E3 + transmitter is set as master unit radio transmission wireless shooting, linked shooting, select orange as color of the LCD panel illumination. When the E3 + transmitter is set as slave unit linked shooting, select orange as color of the panel illumination color: Slave
: AF assist beam LCD panel illumination. When the E3 + transmitter is set as slave unit linked shooting, select green as color of the LCD panel illumination. Enable the AF assist beam Disable the AF assist beam VII. Trouble Shooting Guide 1. Power does not turn on 1.1 Make sure the batteries are installed in correct orientation. 1.2 Check battery contacts are in good contact and that the batteries are sufficient with power. 2.The Slave unit doesnt fire 2.1 Check if the slave unit supports radio transmission wireless flash 2.2 Set the slave unit to <
2.3 Set the transmission channels and wireless radio IDs of the master unit and slave unit to the same numbers. 2.4 Check if the slave unit is within the transmission range of the master unit. 2.5 If using E3+receiver, please refer to the receiver s manual instruction to check the
><
>. operation.
>is displayed 3. <
Set the shutter speed 1 stop slower than the flash sync speed. VIIITechnical Specification Type Compatible cameras Exposure control system On-camera wireless flash trigger EOS type-A camera compatible with E-TTL II/E-TTL autoflash E-TTL/E-TTL auto, manual flash, stroboscopic flash, auto external flash metering only when the flash mode is set to
<Gr>. 2405 2475Hz Primary modulation: OQPSK, secondary modulation: DS-SS Auto, Ch.1-15 0000-9999 Up to 5 groupsA/B/C/D/E, up to 15 units 100m+
1:8-1:1-8:1, 1/2-stop increments Frequency Modulation system Channel Wireless radio ID Slave unit control Transmission distance Flash ratio control Flash exposure compensation FEB FE lock HSS function Manual flash Stroboscopic flash Slave battery check Flash exposure confirmation Modeling flash Linked Shooting Custom functions Personal functions AF assist light Power source Power saving Standby current Static current Dimension Weight(approx.) 3 stops in 1/3- or 1/2- stop increments 3 stops in 1/3- or 1/2- stop incrementswhen used with flash exposure compensation Press the cameras<M-Fn><FEL>or<*>button Provided, high speed sync is possible only with EOS digital cameras released since 2012 1/1-1/1281/3-stop increments Provided( 1 - 500 Hz)
>icon lights, the slave On the master units LCD panel, the <
units AF assist beam emitter blinks and charge the lamp lights Flash exposure confirmation lamp lights 650nm 5mW Injecting distance 1m: L-335mm W-326mm angle of the sector at approx.20 Fired with cameras depth-of-field preview button Provided 8 4 Peak wavelength Optical power Spot diameter at 1m Operating temperature 2 x AA alkaline batteries or AA NI-MH batteries Auto Idle if not operated for 5 min. 70mA 250uA LWH:84.168.358.5mm 118 gExcluding the batteries
-10~+40 Please note: Product specifications and external design are subject to change without further notice.
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2015-05-10 | 2405 ~ 2475 | DXX - Part 15 Low Power Communication Device Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2015-05-10
|
||||
1 | Applicant's complete, legal business name |
Shenzhen Aodelan Technology Co., Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0024506388
|
||||
1 | Physical Address |
4/F, Building 1, Jinhua Ind Park, Langkou Ind Area
|
||||
1 |
Shenzhen, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
f******@us.tuv.com
|
||||
1 | TCB Scope |
A2: Low Power Transmitters (except Spread Spectrum) and radar detectors operating above 1 GHz
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
2AEJW
|
||||
1 | Equipment Product Code |
TGTE3T
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Y******** Z******
|
||||
1 | Title |
Engineer
|
||||
1 | Telephone Number |
+86 7******** Extension:
|
||||
1 | Fax Number |
+86 7********
|
||||
1 |
y******@aodelan.net
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXX - Part 15 Low Power Communication Device Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless Flash Trigger Transmitter | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | Yes | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Audix Technology (Shenzhen) Co., Ltd.
|
||||
1 | Name |
S****** T********
|
||||
1 | Telephone Number |
86-75******** Extension:
|
||||
1 | Fax Number |
86-75********
|
||||
1 |
s******@audix.com.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2405.00000000 | 2475.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC