Installation Insert the lens and the four positioning posts on the camera body into the positioning holes, and tighten the two parts of the use case. Once the lens and body are installed, align them with the metal slots of the battery and press firmly to ensure that the battery clips completely catch the lens and body. MicroSD card slot cover installation Place the SD card with a gold-red side and place it in the SD card slot toward the side where the camera has no screen. Then align the cover to the side of the camera that has no screen, first aligning into the slot. Press firmly on the cover, and make sure that the yellow color at the button is no longer displayed, it is considered to be completely covered with a waterproof board. Please note that the button on the cover and the microphone hole on the bottom are in a vertical line for the correct orientation. If installed in the opposite direction, there may be a risk during exercise. The camera hardware currently used for making samples is not waterproof enough. Camera boot and SD card instructions Press and hold the camera's power button for 2 seconds, and the camera will perform power on/off. The boot animation will display the current firmware version number for confirmation. After the power is turned on, the lens screen appears, but if the blue light flashes, the available MicroSD card is not recognized. When the indicator is green, it means that the memory card has been read and shooting is possible.
* The camera needs to use a MicroSD card that supports the v30 standard. The file format of the card is exFat. The supplied sandisk v30 MicroSD is available. Switch shooting mode and resolution gear to shoot 1. In the upper left corner of the camera shooting preview interface, the displayed information is the number of photos that can be taken or the length of the video that can be taken under the current settings. The right side shows the current battery level. At the bottom left of the screen interface, click to switch the current shooting mode: photo, video. Then click on the bottom right of the screen to switch the resolution and frame rate of the content, or press the power button to switch to normal photo or normal recording mode. Draw a setting menu at the top of the camera screen. Currently only the screen brightness and switch indicators on the left side of the first page are available. Other icon clicks are invalid. 2Among them 1/ 2.3" lens support recording the following:
mode Resolution Frame rate Take a photo (support 4000x3000 shooting dng photos Video 3840x2160 4000x3000 60 30 1920x1080 120 1920x1080 200 HDR Video 3840x1920 30 1. Use APP to connect, control shooting, read back albums, play content 2. 2. Please download the iOS app from the following address (currently only supports iOS https://www.pgyer.com/vL3b 3. 3. After the camera is turned on, please operate the phone only in the system WiFi list and manually connect to the camera's WiFi. The camera WiFi name is the last six digits of the serial number of the camera body. The default connection password is 8 8 (88888888). 4. After the connection is successful, open the OneR APP, click the capture button, enter the shooting interface, set the parameters and shoot (the current version of the APP control camera shooting stability is not enough, it is recommended to use the camera screen to control the shooting). Once you have the content, you can click on the album entry to view the files on the camera's MicroSD card. Click to play or download any file. On the video play page, you need to manually click on the center of the interface to start the video. The thumbnail of the current version of the video and the first frame of the video may show a problem, please pay attention to use. Camera gyroscope calibration method If the camera's anti-shake effect is not good enough, or the picture is drifting. You can now position the camera as shown in the picture with the lens facing down on a full horizontal desktop. Then use your finger to draw the setup menu from the top of the camera screen, and in the lower right corner of the second page menu, click the 50Hz icon to enter the gyroscope calibration interface. You have a 5s countdown time to return to the previous screen to cancel the gyroscope correction. After the 5s countdown is over, the camera will perform the gyroscope calibration. During the calibration process, the camera indicator will flash alternately between blue and green. After the calibration is completed, the camera will automatically restart. Shooting precautions 1. After upgrading the firmware for the first time (for the firmware upgrade method, see the fourth section of the operation guide), be sure to do a gyroscope calibration (see the eighth section for the gyroscope calibration method), otherwise the anti-shake effect may be affected. Gyro calibration can be done only once after upgrading the firmware version after 0.0.17. 2. After the firmware is successfully upgraded for the first time, the camera will automatically turn on. But please don't shoot directly, you need to restart the camera to be normal, otherwise the anti-shake effect may be abnormal if you shoot directly. 3. At present, regardless of the 1080P high frame rate of 1/2.3" or 1" lens, the picture quality is not very good. It is recommended to use only the stationary position to shoot moving objects in a scene with good light. 4. Use 1" lens to shoot night scenes. It is recommended to use 5.4K@30fps and raw photos. The picture quality of 4K@60 and 1080P@120 frames is not good enough. 5. If you used a 1/2.3" lens to take a photo with the manual exposure parameter, first switch the exposure mode to auto exposure, then switch to the recording mode to shoot. Avoid some bugs. 6, 1 / 2.3" lens 1080P@120fps gear position, the current settings exposure, white balance and other parameters will not take effect. 1080P@200 switching white balance does not take effect. Other resolution gears are normal. 7. The current APP version will play a few errors when connecting to view the camera album, but it will not affect the use, and the album will disappear when the error pop-up window disappears. This bug will be fixed tomorrow. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. other antenna or transmitter. The device must not be co-located or operating in conjunction with any This device complies with FCCs radiation exposure limits set forth for an uncontrolled environment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. 5.15-5.25GHz Band Operations in the 5.15-5.25GH band are restricted to indoor use only.