Fingerprint smart terminal BM5510 Users Manual V1.2 ShenZhen Aratek Biometrics Technology Co.,Ltd.
- 1 -
1. Warm Tips
(1) The manual is subject to change without prior notice.
(2) The manual is a general guide for the device. Functions might be increased or reduced due to customized needs. Please contact local distributor for details. 2. Warning Unauthorized disassembl is forbidden, or else at your own risk. Do not try to charge the battery on other chargers. Do not dispose of the device in a fire or heat as that may cause crack and injury. 3. Product Introduction
(1) Product Photos a).Front and Back of the device
- 3 -
b). Sides of the device
(2). Components No. 1 Name Sensor Function Place finger on capture area to capture
- 4 -
fingerprint Display working state Listen to the sound (optional) Collect soundoptional 2 mega pixel (optional) LED flashlight Broadcast or call 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Indicator light Receiver*
MIC *
Camera*
Flashlight Loudspeaker Volume button+ Volume up Volume button- Volume down TF card slot Headphone port Power switch Reset button SIM slot 1*
SIM slot 2*
Micro USB USB interface UART port*
32G flash memory support 3.5mm On and off the power/the screen Device restart Install Micro SIM (optional) Install Micro SIM (optional) Communication port and charging port Insert USB device such as keyboard, mouse Reserve function 4. The Quick Start Guide
(2) On /off operation
(1) Charging operation AC adapter is USB port adapter. Plug the USB connector into adapters USB port while the other side into the devices Micro-USB port. Plug in AC adapter for charging. When the device is power-off, long press the power key for 5 seconds, and the device vibration or screen-on indicates start-up. When the device is power-on, short press the power key to get into standby or wake-up. When the device is power-on but not standby mode, press the power key for over 2 seconds then pop up interface of power off, airplane mode and silent mode. Then select power off.
(3) Please power off the device before inserting or removing the SIM card, otherwise the device may be damaged. 5. The Index Hardware Parameters Items CPU Display screen Detailed description 1.2GHz dual core processor 5.0 inch, 854480 pixels
- 5 -
Touch screen RAM SIM card*
Onboard Expansion Rear Decoder Built-in Mic*
Receiver Speaker Headphone port Mirco USB USB TF Card slot UART port Data ROM Camera Audio Interface Button Antenna Input G-Sensor*
Light- sensor*
Proximity sensor*
GPS*
GSM*
GPRS*
Fingerprint Wireless Power Sensor Capture size Resolution WiFi Bluetooth 4.0*
3G*
Battery Power supply OSOperating System Accessories Net weight Dimension capacitive touch screen 1G RAM Optional 8G ROM TF Cardup to 32G) 2 mega pixel Support 2.1 sound output Quantity: 1 Optional Stereo Speaker 3.5mm Quantity: 1 USB OTG 2.0 Quantity: 1 Optional Power Switch Built-in Virtual Keyboard Optional Optional Optional Optional GSM 850/900/1800/1900 MHz, WCDMA 2100 MHz, WCDMA 900 MHZ Optional GPRS, EDGE, HSPA optional Capacitive 10.64mm14mm 500dpi WiFi 802.11bgn Optional Optional 2000mAh Li-polymer DC 5V/1.5A USB cable Android 4.4 AC adapter USB Cable 380g 185mm*82mm*43mm
- 6 -
Extensive function*
Operating environment Built-in QR Code (Optional) Working temperature: 070 Relative humidity 90%
Storage and transportation temperature EMC
-4060 Support Radio frequency Specification*
field direction Antenna energy output surface magnetic Antenna strength (Hmax) 7.5A/m(rms) Electromagnetic field strength at the 3cm of the antenna surface normal
(Hmin) 1.5A/mrms Bit rate: 106Kbit/sfc/128 Modulation Mode: ASK Modulation Modulation index: 814 Coding mode: NRZ-L Subcarrier frequency (fs): 847kHz Modulation subcarrier mode: BPSK Subcarrier modulation input:
Modulation output:
ry is installed in the terminal. Note: * part is optional according to client requirement. 6. About the Battery High-performance 2000mAh Li-polymer batte
(1) Battery Life Up to 5 hours for continuous work, standby for a week.
(2) Charging Method Please charge your battery in time when the system battery alarms. A full charge to 100% is necessary.
(3) Time for Charging A standard 2000mAh battery charge takes about 6-8 hours.
(4) Operating Notice a. The standby time is measured in an actual environment, but the specific standby time may vary in different areas. This is due to various factors. b. A rechargeable battery for the device can charge and discharge hundreds of times, but it will eventually wear out. When standby times are noticeably shorter than normal, replace the original battery.
- 7 -
c. Disconnect the device and unplug charger after use. d. If no in use for long period, battery may cause hibernation. Battery should be kept in dry environment with full charge. Charge and discharge once every 3 to 6 months is recommended. e. Use designated battery for replacement. 7. Genuine Accessories
(1) USB data cable
(2) AC adapter
(3) Battery 8. Simple Troubleshooting Guide phenomenon Cause Abnormal Charge Heating Not full insertion of AC adapter into household outlet Poor contact of USB port Normal phenomenon under service conditions Crash Malware running or BUG in running software Operation Check plug insertion Ensure good contact of USB port Avoid using in a too hot environment, or stop operation for a while Press reset button, avoid malware in usage 9. Maintenance & Repair
(1) Keep the device dry in case rain, humidity and all kinds of liquids or moisture containing minerals will erode electronic wires.
(2) Avoid using and storing the device in dusty and dirty place in case detachable parts and internal electronic components damaged.
(3) Do not put the device in a too hot place because high temperature shortens the life of electronic devices, destroys batteries, deforms and melts some plastic components.
(4) Do not store the device in a too cold place. Or else when the temperature of the device rises (to normal temperature), humidity appears inside it then destroys circuit board.
(5) Open the device in accordance with the manual, do not try other methods.
- 8 -
(6) No throw, beat or vibration allowed, because that will damage the inner circuit board and its precision architecture.
(7) Do not clean the device with strong chemicals, cleaning agents and strong detergents.
(8) Do not paint the device because paints affect detachable parts work smoothly.
(9) The charger is for indoor use only.
(10) Capacitive touch panel designation, avoid extrusion with hard objects, scratch or rude touching in case touch panel fracture or failure.
(11) Power off while long time no use.
(12) Abnormal situation may happen due to increasing electromagnetic interference. Please reboot system to recovery. The suggestions above are applicable equally to the product, battery, charger and all accessories. If abnormal situation of any accessory happens, contact local authorized agents for replacement or maintenance.
- 9 -
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: BM5510 (FCC ID: 2AGUJ-BM5510) has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the handset kept 0 cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0 cm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.