2019-1 10-10
7 1.1 1
Wireless 720
P AHD back u up camera 0 Lux 1024
600Pixel 40 HM134 h 4G n 1/4inch 90
5
5 50 ng device:
Imagin pecification Lens sp ontal angle Horizo Vertica al angle ng Imagin resolut tion mum Minim nation illumin Transm mit power Workin ng ncy frequen
@2400~250 2.0dBi na gain Antenn 8 IEEE 8 System m
02.11b/g M 150CM h of cable Length 24V e DC12/2 ting Voltage Operat Workin ng current Max 35 50mA (@12 ting Operat temper rature
IR dBm to +65C 2.4GHz
-20C t 182 z~2.4835GH Hz 2V) 00MHz
00MHz AHD
1024
600Pixel m y -94dBm z~2.4835GH 2.4GHz Hz t signal Output t resolution Output t sensitivity Accept ng Workin ncy frequen
@2400~250 2.0dBi Antenn na gain 8 IEEE 8 m System
02.11b/g Transm mission
[1]
100M [
range
[2]
200ms[
cy time Latenc 50CM h of cable Length e DC12/2 ting Voltage Operat Max 25 ng current Workin ting Operat rature temper
24V 50mA (@12 to +65C
-20C t 2V)
FOSP-RVC C-W8Exten nsion cable 4 4.2m 1
1.W wor prom scre char test.
When the rec rking, the p mpt is outpu een or real-t racter in the
. It has noth
ceiver is po ower-on ind ut, only wh time video s e upper righ hing to do w owered on fo dicator flash hen the code screen. No s ht corner of with this pro for the first hes once an e operation signal prom the figure i oduct. The s time, the co nd enters th or the came mpts are sho is the input ame conten ode is not p he no-signal era signal is own in Figur signal chan nt will be the paired, and l state direc s connected re 1. (Note:
nnel indicato e same in th camera is n the paired c not
No Signal ctly. The
ch to the cod de
. Will switc HD1 whi ite
: The AH est used in th or for the te he g) he following Pict ture 1No sign nal 2.Pr cod end first than incr show ress and ho e to count d s. The came t 15S of the n 10S of the rease; if the wn in Pictu ld the butto down to 30S era and the e power-on e countdown pairing tim re 2. on 3S on th S in the inte receiving b n defaults to n of the rec mes out, the e receiving erface. Pleas box can esta o the code w ceiving box receiving b box to rec se power on ablish the c waiting stat
. If it is less box will re-
eive and en n the camera communicat te. Therefor s than 10S, enter the no nter the cod a to be paire tion connec re, it is reco the pairing o-model sta de interface. ed before th ction by the ommended timeout pro ate. The cod Wait for th he he countdow wn mselves; Th he ore to pair mo will obability w is de interface Picture 2Pair code interface 3.If the communication connection is successfully established in the above steps, the real-time video screen display screen will be automatically entered, and the yellow signal strength icon will be displayed in the upper left corner. The total connection signal status is represented by 0 to 4 total 5 grids. The actual picture of F is shown in Picture 3, and the imaging effect is shown in Picture 4. Picture 3F Normal view 4.In the case of high illumination brightness, the camera outputs a color video signal by default. As shown in Picture 5. Picture 4Mirror view Picture 5Color mode 5.In the nighttime environment where the illumination is very low, the camera automatically turns on the infrared light to fill the light, and the camera switches to the night mode to output a black and white video signal. As shown in Picture 6. Picture 6Night mode 6.View firmware version: Press the receiving box button 3 times in succession, the receiving box and camera current firmware version 5S will be superimposed in the video; in the unconnected state, only the receiving box firmware version will be displayed, as shown in Picture 7; in the communication connection state At the same time, the corresponding firmware version of the receiving box and camera is displayed, as shown in Picture 8. (Note: Picture 7 and Picture 8 are for reference only, the subsequent version number is displayed in the center, and only the receiving box version number is displayed in the unconnected state) Picture 7Reciver firmware version Picture 8Receiver and rear view camera firmware version Remarks:
[1] Measure data in an open, unobstructed, electromagnetically free environment.
[2] Camera to receiver box image transmission delay time. The above data is for reference only; the data may be subject to environmental impact errors, please refer to the actual.
Made by Sales confirm Songming He Engineering review Producting signature Steady on, the receiving box works normally, and the signal transmission is normal. Fast flash, the receiving box works normally, in the code mode Normally off, the receiving box works normally, and it is in no signal/unpowered state. Flash once, the receiving box is turned on Purchase signature:
Gerneral Manager Date 2019.08.30 2019.10.10 Version V1.0 V1.1
Issue Description First issue Upgrade transmission power specification FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions
(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.