BL-M8189FS6(VC) 802.11n 150Mbps WiFi SDIO Module Specification SHENZHEN BILIAN ELECTRONIC CO., LTD Add: 10~11/F, Building 1A, Huaqiang idea park, Guangming district, Shenzhen. Guangdong, China Web: www.b-link.net.cn Module Name: BL-M8189FS6(VC) Module Type: 802.11b/g/n 150Mbps 1T1R WiFi SDIO Module Revision: V1.0 Customer Approval:
Company:
Title:
Signature:
Title:
Signature:
BL-link Approval:
Date:
Date:
Revision History Revision Summary 1.0 Official release Release Date 2020-03-25 1 http://www.b-link.net.cn BL-M8189FS6(VC) is a highly integrated WiFi module, it contains a WLAN MAC, a 1T1R capable WLAN base band. It supports IEEE 802.11b/g/n standard and provides the highest PHY rate up to 150Mbps, offering feature-rich wireless connectivity and reliable throughput from an extended Operating Frequencies:
2.412~2.462GHz Host Interface is SDIO 2.0 IEEE Standards:
IEEE 802.11b/g/n Wireless data rate can reach up to 150Mbps Connect to external antenna through half hole pad Power Supply:
3.30.2V main power supply;
3.30.2V or 1.80.1V for VDIO
(SDIO and Digital 1. Introduction distance. 1.1 Features I/O power supply) 1.2 Block Diagram 2 http://www.b-link.net.cn 1.3 General Specifications Module Name BL-M8189FS6(VC) WiFi Module Chipset RTL8189FTV-VC-CG WiFi Standards IEEE802.11b/g/n/, 1T1R, 2.4GHz, 150Mbps (Max) Host Interface SDIO 3.0 Antenna Dimension Power Supply Connect to the external antennas through half hole pad SMD 44Pins, 12*12*1.5mm (L*W*H) DC 3.30.2V(main power) @ 350 mA (Max) DC 3.30.2V or 1.80.1V(SDIO and Digital I/O power) Operation Temperature
-10 to +70 Operation Humidity 10% to 95% RH (Non-Condensing) 2. Pin Assignments No Pin Name Type Description Supply Top view 2.1 Pin Definition GND ANT GND NC RF RF RF
Ground connections WLAN RF port Ground connections NC 1 2 3 4 3 http://www.b-link.net.cn VDD33 3.3V Main power supply WL_REG_ON Power down select (active low) WLAN to wake-up HOST, pull high for use VDD33 VDIO VDIO for SDIO and Digital I/O pin, the power supply is same as the signal level of SDIO bus. Base on platform to choose 3.3V or 1.8V NC NC NC NC NC NC WAKE SD_D2 SD_D3 SD_CMD SD_CLK SD_D0 SD_D1 GND NC VDIO NC NC NC NC NC NC NC NC GND NC GND NC NC NC NC GND O I/O I/O I/O I I/O I/O
I P P
P
P
P
P
NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC SDIO data line SDIO data line SDIO command line SDIO clock line SDIO data line SDIO data line Ground connections Ground connections Ground connections Ground connections 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 4 http://www.b-link.net.cn 39 40 41 42 43 44 NC NC NC NC NC NC
NC NC NC NC NC NC P: Power, I: Input, O: Output, I/O: In/Output, RF: Analog RF Port 3. Electrical and Thermal Specifications 3.1 Recommended Operating Conditions Parameters Ambient Operating Temperature External Antenna VSWR Supply Voltage VDD33 VDIO(1.8V) Min
-10 1 3.1 1.7 Typ 25 1.92 3.3 1.8 Max Units 70 2.5 3.5 2.0
V V 3.2 Current Consumption Conditions : VDD33=3.3V ; Ta:25 Use Case WiFi Radio Off (Linux Driver) WiFi Unassociated (Linux Driver) 2.4G 1Mbps TX (RF-Test) 2.4G 1Mbps RX (RF-Test) 2.4G 11Mbps TX (RF-Test) 2.4G 11Mbps RX (RF-Test) 2.4G 6Mbps TX (RF-Test) 2.4G 6Mbps RX (RF-Test) VDD33 Current (average) Typ Max Units 40 40 273 60 280 55 265 60 50 60 320 70 320 70 285 70 mA mA mA mA mA mA mA mA 5 http://www.b-link.net.cn 2.4G 54Mbps TX (RF-Test) 2.4G 54Mbps RX (RF-Test) 2.4G MCS0(HT20) TX (RF-Test) 2.4G MCS0(HT20) RX (RF-Test) 2.4G MCS7(HT20) TX (RF-Test) 2.4G MCS7(HT20) RX (RF-Test) 2.4G MCS7(HT40) TX (RF-Test) 2.4G MCS7(HT40) RX (RF-Test) 260 60 275 60 265 59 275 60 270 65 287 70 282 70 291 80 mA mA mA mA mA mA mA mA 4. Interface Functional and Timing Specifications 4.1 SDIO Power On Sequence 6 http://www.b-link.net.cn 4.2 SDIO Timing 5. WiFi RF Specifications 5.1 2.4G WiFi RF Specification Conditions : VDD33=3.3V ; Ta:25 Features Description WLAN Standard IEEE 802.11b/g/n CSMA/CA Frequency Range 2.412~2.462GHz
(2.4GHz ISM Band) Channels Ch1~Ch11
(For 20MHz Channels) Modulation 802.11g (OFDM): BPSK, QPSK, 16QAM, 64QAM;
802.11b (DSSS): DBPSK, DQPSK, CCK;
802.11n (OFDM): BPSK, QPSK, 16QAM, 64QAM;
802.11b: 1, 2, 5.5, 11Mbps;
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps;
802.11n (HT20): MCS0~MCS7(1T1R_SISO) 6.5~72.2Mbps;
802.11n (HT40): MCS0~MCS7(1T1R_SISO) 13.5~150Mbps;
Date Rate Frequency Tolerance 15ppm 7 http://www.b-link.net.cn 6. Mechanical Specifications 6.1 Module Outline Drawing Module dimension: 12.0*12.0*1.5mm (L*W*H; Tolerance: 0.15mm) 8 http://www.b-link.net.cn Module Bow and Twist0.1mm 6.2 Mechanical Dimensions 7. Application Information 7.1 Typical Application Circuit 9 http://www.b-link.net.cn 7.2 Recommend PCB Layout Footprint Design size mm Top View 7.3 Reflow Soldering Standard Conditions Please use the reflow within 2 times. Set up the highest temperature within 250. 10 http://www.b-link.net.cn 8. Key Components Of Module No. Parts Specification Manufacturer Note 1 Chipset RTL8189FTV-VC-CG Realtek 2 PCB BL-M8189FS6 Shenzhen Tie Fa Technology limited Guangdong KINGSHINE ELECTRONICS CO., LTD Quzhou Sunlord Electronics Co., Ltd HUBEI TKD ELECTRONICS TECHNOLOGY CO., LTD. LUCKI CM ELECTRONICS CO., LTD HOSONIC ELECTRONIC CO., LTD. SHENZHEN KAIYUEXIANG ELECTRONICS CO., LTD WAY ON ELECTRONIC CO., LTD. UN Semiconductor Co., Ltd 3 Crystal 26MHz-9pF-10ppm-3225 4 TVS diode TVS diode 0402 9. Package and Storage Information 9.1 Package Dimensions 11 http://www.b-link.net.cn Package specification:
1. 2000 modules per roll and 10,000 modules per box. 2. Outer box size: 37.5*36*29cm. 3. The diameter of the blue environment-friendly rubber plate is 13 inches, with a total thickness of 28mm (with a width of 24mm carrying belt). 4. Put 1 package of dry agent (20g) and humidity card in each anti-static vacuum bag. 5. Each carton is packed with 5 boxes. 9.2 Storage Conditions Absolute Maximum Ratings:
Storage temperature: -45 to +85 Storage humidity: 10% to 95% RHNon-Condensing Recommended Storage Conditions:
Storage temperature: 5 to +40 Storage humidity: 20% to 90% RH Please use this Module within 12month after vacuum-packaged. The Module shall be stored without opening the packing. After the packing opened, the Module shall be used within 72hours. When the color of the humidity indicator in the packing changed, the Module shall be baked before soldering. Baking condition: 60, 24hours, 1time. ESD Sensitivity The Module is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions!
12 http://www.b-link.net.cn ISED Statement English: This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, a nd (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES3 (B)/NMB3(B). French: Le prsentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradi olectriquesubi, mmesi le brouillageest susceptible d'encompromettre le fonctionnement. This radio transmitter (ISED certification number: 20944-M8189FS6) has been approved by Industry Canada to operate with the antenna types listed with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (ISED certification number: 20944-M8189FS6) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Radiation Exposure Statement This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations Cet quipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrl. Cet quipement doit tre install et utilis distance minimum de 20cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following condition:
The transmitter module may not be co-located with any other transmitter or antenna. As long as the condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:
Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. Note Importante:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l' IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final
(y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling The final end product must be labeled in a visible area with the following: Contains IC: 20944-
M8189FS6. Plaque signaltique du produit final Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: Contient des IC: 20944-M8189FS6 Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) thi s device may not cause harmful interference, and (2) this device must accept any interference received, incl uding interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursua nt to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inte rference in a residential installation. This equipment generates uses and can radiate radio frequency energy a nd, if not installed and used in accordance with the instructions, may cause harmful interference to radio com munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help important announcement Important Note:
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. This device is intended only for OEM integrators under the following conditions:
1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna, 3. For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. (if modular only test Channel 1-11) As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following" Contains FCC ID: 2AL6KBL-
M8189FS6"
Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter 2.3 Specific operational use conditions different This module operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.4 Limited module procedures This module is Limited single modular without shielding, host manufacturer have to consult with module manufacturer for the module limiting conditions when integrate the module in the host. module manufacturer should reviews detailed test data or host designs prior to giving the host manufacturer approval. is stand-alone modular. Multiple simultaneously transmitting condition product involve If the end the will or 2.5 Trace antenna designs Not applicable 2.6 RF exposure considerations This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 2.7 Antennas This radio transmitter 2AL6KBL-M8189FS6 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Model Type Connector 2400-2483.5 5150-5250 5250-5350 5470-5725 5725-5850 Peak gain ( dBi ) MHz 2.0dBi MHz
MHz
MHz
MHz
2400-2483.5 MHz External Antenna
2.8 Label and compliance information The final end product must be labeled in a visible area with the following" Contains FCC ID:2AL6KBL-M8189FS6". Information on test modes and additional testing requirements 2.9 Host manufacturer which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result comply with FCC part 15.247 and 15.209 requirement, then the host can be sold legally. 2.10 Additional testing, Part 15 Subpart B disclaimer Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.