BL-R7603NU3 802.11n 300Mbps WiFi USB Module Specification SHENZHEN BILIAN ELECTRONIC CO., LTD Add: 10~11/F, Building 1A, Huaqiang idea park, Guangming district, Shenzhen. Guangdong, China Web: www.b-link.net.cn Module Name: BL-R7603NU3 Module Type: 802.11b/g/n 300Mbps 2T2R WiFi USB Module Date:
Date:
Revision: V1.0 Customer Approval:
Company:
Title:
Signature:
Title:
Signature:
BL-link Approval:
Revision History Revision Summary 1.0 Official release Release Date 2020-07-17 1 http://www.b-link.net.cn 1. Introduction BL-R7603NU3 wireless module is designed base on MT7603U . It is a wifi module which can support far than 100M communication. It operates at 2.4~2.4835GHz and supports IEEE802.11b/g/n 2T2R , wireless data rate can reach up to 300Mbps. 1.1 Features Operating Frequencies: 2.4~2.4835GHz Host Interface is USB 2.0 IEEE Standards: IEEE 802.11b/g/n Wireless data rate can reach up to 300Mbps PIFA antenna Power Supply: 5V0.25V main power supply 1.2 Block Diagram 2 http://www.b-link.net.cn 1.3 General Specifications Module Name IEEE 802.11b/g/n 300Mbps WiFi USB Module Chipset MT7603U WiFi Standards IEEE802.11b/g/n/, 2T2R MIMO, 2.4GHz, 300Mbps (Max) Host Interface USB2.0 Antenna PCB antenna Dimension 45*25*5.5mm (L*W*H) Power Supply 5V0.25V @ 600 mA (Max) Operation Temperature
-20 to +70 Operation Humidity 10% to 95% RH (Non-Condensing) Storage Temperature
-45 to +85 Storage Humidity 10% to 95% RH (Non-Condensing) 2. Pin Assignments 1 2 3 4 5 6 7 8 2.1 Pin Definition No Pin Name Type Description HOST_WAEK_WL Host wake up WLAN NC GND RST GND USB+
USB-
No connection GND System reset GND
P I I P I/O I/O USB 2.0 differential data line USB 2.0 differential data line USB_5V P Power supply, 5V0.25V P: Power, I: Input, O: Output, I/O: In/Output, RF: Analog RF Port Supply VDD33 VDD33 3 http://www.b-link.net.cn 3. Electrical and Thermal Specifications 3.1 Recommended Operating Conditions Parameters Min Typ Max Units Ambient Operating Temperature External Antenna VSWR
-20 1 25 1.7 70 1.9 Supply Voltage VDD5V 4.75 5 5.25 Symbol Parameter Min Typ Max Units 3.2 Digital I/O DC Specifications VIH VIL VOH VOL Input High Voltage Input Low Voltage Output High Voltage Output Low Voltage 3.3 Current Consumption Conditions : VDD=5V ; Ta:25 Use Case 2.4G 1Mbps TX (RF-Test) 2.4G 1Mbps RX (RF-Test) 2.4G 11Mbps TX (RF-Test) 2.4G 11Mbps RX (RF-Test) 2.4G 6Mbps TX (RF-Test) 2.4G 6Mbps RX (RF-Test) 2.4G 54Mbps TX (RF-Test) 2.4G 54Mbps RX (RF-Test) 1 V V V V V mA mA mA mA mA mA mA mA 2.0
2.97 0 3.3 0
3.6 0.9 3.3 0.33 VDD33 Current (average) Max Units Typ 480 68 475 68 392 67 198 67 483 69 480 69 395 68 202 68 4 http://www.b-link.net.cn 430 67 208 68 375 77 167 78 431 68 210 69 380 79 172 80 mA mA mA mA mA mA mA mA 2.4G MCS0(HT20) TX (RF-Test) 2.4G MCS0(HT20) RX (RF-Test) 2.4G MCS7(HT20) TX (RF-Test) 2.4G MCS7(HT20) RX (RF-Test) 2.4G MCS7(HT40) TX (RF-Test) 2.4G MCS7(HT40) RX (RF-Test) 2.4G MCS15(HT40) TX (RF-Test) 2.4G MCS15(HT40) RX (RF-Test) 4. WiFi RF Specifications 4.1 2.4G WiFi RF Specification Conditions : VDD=5V ; Ta:25 Features Description WLAN Standard IEEE 802.11b/g/n CSMA/CA Frequency Range 2.4~2.4835GHz (2.4GHz ISM Band) Channels Ch1~Ch13 (For 20MHz Channels) Modulation 802.11g (OFDM): BPSK, QPSK, 16QAM, 64QAM;
802.11b (DSSS): DBPSK, DQPSK, CCK;
802.11n (OFDM): BPSK, QPSK, 16QAM, 64QAM;
802.11b: 1, 2, 5.5, 11Mbps;
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps;
802.11n (HT20): MCS0~MCS7(1T1R_SISO) 6.5~72.2Mbps;
802.11n (HT20): MCS8~MCS15(2T2R_MIMO) 13~144.4Mbps;
802.11n (HT40): MCS0~MCS7(1T1R_SISO) 13.5~150Mbps;
802.11n (HT40): MCS8~MCS15(2T2R_MIMO) 27~300Mbps;
Date Rate Frequency Tolerance 15ppm 5 http://www.b-link.net.cn 2.4G Receiver Specifications RX Rate Min Input Level(Typ) Max Input Level(Typ)
-10dBm
-10dBm
-10dBm
-10dBm
-10dBm
-10dBm
-10dBm
-10dBm PER
< 8%
< 8%
< 10%
< 10%
< 10%
< 10%
< 10%
< 10%
802.11b@1Mbps 802.11b@11Mbps 802.11g@6Mbps 802.11g@54Mbps 802.11n@HT20_MCS0 802.11n@HT20_MCS7 802.11n@HT40_MCS0 802.11n@HT40_MCS7
-93dBm
-87dBm
-89dBm
-73dBm
-88dBm
-68dBm
-86dBm
-68dBm 5. Mechanical Specifications 5.1 Module Outline Drawing Top view Side view Module dimension: 45*25*5.5mm (L*W*H; Tolerance: 0.15mm) 6 http://www.b-link.net.cn Module Bow and Twist0.1mm 6. Package and Storage Information 6.1 Package Dimensions 6.2 Storage Conditions Absolute Maximum Ratings:
Storage temperature: -45 to +85 Storage humidity: 10% to 95% RHNon-Condensing Recommended Storage Conditions:
Storage temperature: 5 to +40 Storage humidity: 20% to 90% RH Please use this Module within 12month after vacuum-packaged. The Module shall be stored without opening the packing. After the packing opened, the Module shall be used within 72hours. When the color of the humidity indicator in the packing changed, the Module shall be baked before soldering. Baking condition: 60, 24hours, 1time. ESD Sensitivity The Module is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions!
7 http://www.b-link.net.cn FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) thi s device may not cause harmful interference, and (2) this device must accept any interference received, incl uding interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursua nt to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inte rference in a residential installation. This equipment generates uses and can radiate radio frequency energy a nd, if not installed and used in accordance with the instructions, may cause harmful interference to radio com munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help important announcement Important Note:
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. This device is intended only for OEM integrators under the following conditions:
1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna, 3. For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. (if modular only test Channel 1-11) As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following" Contains FCC ID: 2AL6KBL-
R7603NU3"
Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter 2.3 Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs Not applicable 2.6 RF exposure considerations This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 2.7 Antennas This radio transmitter 2AL6KBL-R7603NU3 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Model Type Connector 2400-2483.5 5150-5250 5250-5350 5470-5725 5725-5850 Peak gain ( dBi ) MHz 2.0dBi MHz
MHz
MHz
MHz
2400-2483.5 MHz External Antenna
Information 2.8 Label and compliance information The final end product must be labeled in a visible area with the following" Contains FCC ID:2AL6KBL-R7603NU3". 2.9 requirements Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host. 2.10 Additional testing, Part 15 Subpart B disclaimer Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B. additional testing modes and test on