Cadence and Speed Sensor User Manual Model: CDN200 Thank you for selecting this Cadence and Speed Sensor! CDN200 can track and monitor your cadence and speed on APP. Packaging contents Main Unit x 1 Crank rubber pad x 1 Wheel rubber pad x 1
Fix Ring x 3 Battery CR2032 x 1 Mode select mode when power up when power up 1. Cadence mode: the Blue LED is on to indicate the unit is on cadence 2. Speed mode: the RED LED is on to indicate the unit is on speed mode 3. To switch cadence and speed mode , just need reinstall the battery . How to install the cadence and speed sensor on your bike Its recommended you secure your bike on a stand while installing the sensor. Installing the cadence sensor 1. Place and hold the crank rubber pad on the inside of the non-drive side crank arm , then place cadence sensor . 2. Tied the cadence sensor and crank arm with the silicone ring 3. Rotate the crank arm to check for clearance. Take a few minute test ride and inspect the sensor to ensure there is no interference. Installing the speed sensor 1. Place and hold the wheel rubber pad and speed s e n s o r o n t o p o f t h e wheel hub 2. Tied the sensor and hub with the silicone ring 3. Rotate the wheel to check for clearance. The sensor should not contact other parts of your bike How to track and monitor your data 1. First time you choose you prefer APP to install your smartphone such as Polar beat, Wahoo Fitness, Endomondo Runtastic PRO, Zwift. X-fitness etc. Wahoo Fitness Polar Beat Zwift X-Fitness 2. Then you connect the sensor to your device using Bluetooth technology, it need pair when you start . BLUETOOTH How to replace the battery The device uses one CR2032 battery. APP will remind that a low battery level and need replacement 1. Twist the cover counter-
c l o c k w i s e u n t i l t h e cover is loose enough to remove. 2. Remove the cover and the battery . 3. Insert the new battery into the cover, observing polarity.
Caution
"Do not ingest battery, Chemical Burn Hazard"
NOTE: Do not damage or lose the O-ring gasket. 4. Twist the cover clockwise so that the marker on the cover aligns with the 5. NOTE: The LED flashes Blue to indicate that is cadence mode, RED is marker on the case. for Speed mode. Specification Dimensions 38.5x38.0x12.0mm connectivity Weight Battery BLE Transmission range 20m Data format 10.5g CR2032 Ble bicycle speed/cadence profile Battery life Water proof 6 months at 2 hours per day IP67 Responsible time Detected range 2 s 300 RPM Troubleshooting If your device will not connect to the speed and cadence sensors, you can try to Rotate the crank arm or wheel two revolutions to wake up the sensor. Or check battery level via APP and replacement need reinstall battery if no LED flash when replace battery. EU-DECLARATION OF CONFORMITY Hereby, declares that Cadence and Speed Sensor (model: CDN200) is in compliance with the essential requirements and other relevant provisions of Directive RED 2014/53/EU. A copy of the signed and dated Declaration of Conformity is available FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.