Cautions
•
•
Please do not install under the metal desktop.
Avoid placing any metal/magnetic objects (keys, coins, credit
cards, IC card, etc.) around the charger to prevent any damage.
Please make sure there's no metallic material in the phone
case.
Please use the orginal power adapter for best performance.
Do not expose the charger to liquids which might cause
danger.
Do not disassemble or modify the charger.
Keep away from children.
•
•
•
•
•
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance
20cm between the radiator & body.
Cable clips
Power adaptor
Resonator pad
Sticker
Align board
Charger
6
5
4
3
2
1
6
5
4
3
2
1
OK
QB06
Through surface wireless charger
•
•
•
•
Support all Qi-BPP compatible phones 5W
iPhone fast charge 7.5W
Samsung fast charge 10W
Protection: OCP, OVP, OTP, FOD
Power input: 19V, 0.94A
Charging distance:
10-20mm, with sticker
15-30mm, with resonator pad
Shenzhen Ciji Technology Co., Ltd
Address: 1807, Unit 1, Overseas Chinese Scholars Venture Building,
No.29, Gaoxin South Ring Road, Nanshan District, Shenzhen, Guangdong,
China
Email: info@tseetech.com
Phone: +86 755 26417632
- Non-Compatible Phone.
- Phone is too close: Keep the distance greater than 15mm.
object.
- FOD: foreign object is detected, please remove the foreign
Red: Error!
Solid Blue: The charger is in charging mode.
use.
Slowly On/Off Blue: The charger is in stand-by mode, ready to
LED indicator interpretation:
Since the coil sizes are different, only support mobile phone.
Watch?
Is it compatible with other products, such as airpod or Apple
is between 30-50mm.
Thickness should be between 15-30mm, resonator is needed if it
How does the desk thickness impact the charging?
there's no metal material being used.
Please also check the material of the phone case, make sure
resonator).
when the phone is placed horizontally aligned with the sticker (or
middle of the phone, so it will activate the best performance
The phone's wireless charging coil is usually located in the
Phone isn't charging/charging very slow.
•
•
•
•
Troubleshooting
Contents
Installation
1. Clean the desk bottom.
2. Peel the film of the double-sided adhesive pad and stick it to
the chosen place under the desk.
3. Use the align board to find the correct area for the sticker or
resonator, make sure they're horizontally aligned, mark with a
pencil.
4. Peel the film of the sticker or resonator pad (according to the
charging distance), and paste if on the desktop where has
been marked.
5. Plug in & power-on test.
OK
OK
OK
OK
Use sticker
for 10-20mm charging distance
Use resonator pad
for 15-30mm charging distance