H1 Sound Machine+bluetooth speaker Please read the instruction manual before operating the Sound Machine Bluetooth Speaker Main Function Instruction Wireless Charger Transmitter Specification 1.Speaker Power:5W;
2.Input Voltage:DC 5V/2A;
3.Wireless Charging Power:5W;
2.Rain 1.White Noise 3.Fireside 4.Warble 9.ONVolume+
8.OFFVolume-
5.Ocean wave 6.Wind 7.Timer:15/30/60minutes;
Operation Instruction Sound Machine Mode:
1.Sleeping Songs:1.White Noise;2.Rain;3.Fireside;
4.Warble;5.Ocean wave 6.Wind ;
7.Timer:15/30/60minutes;
S a f e t y I n f o r m a t i o n 2. Do not put the device in the place close to Heater, Microwave, Electronic Cooker, which may cause the device overheated and lead a fire. 3. Do not frequently fall or bump the device, which may cause the explosion. 4. Do not let children play or use the device when adult is not presented. 5.Do not put or use the device in the environment of low temperature or humidity, the normal environment temperature should be 0-50. 6. Do not disassemble or repair the device personally. 7. Do not put the magnetic stripe like bank card close to the device, which may cause the magnetic failure. 8. Do not put the device close to medical instruments in the range of 20cm. Which may cause signal interference. 9. Please make sure the charged device being off the protect cover before directly charging to wireless charger. 10. Please plug off the adapter when not using the device, which can save the life time and avoid the damage., 10.MICRO USB 11.Timed shutdown: 60 minutes
(press the timed button for the third time, voice prompt "60 minutes", the 60 minutes light is on at the same time, and then cycle) 13.Timed shutdown: 15 minutes
(press the timed button for the third time, voice prompt "15 minutes", and the 15-minute light will come on at the same time) 12.Timed shutdown: 30 minutes
(press the timed button for the third time, voice prompt "30 minutes", and the 30 minutes light will come on at the same time) Caution:
Please read following cautions to avoid the unexpected emergency during using the wireless charger . 1. Do not directly touch the device when it is overheated, which may bring scald hurt. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC Statement This device complies with part 15 and part 18 of the FCC Rules. Operation is Subject To the following two conditions:
(1) This device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the partyresponsible for compliance could void the user's authority tooperate this equipment. Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 and part 18 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Increase the separation between the equipment and any other radio device. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.