FCC ID: 2AUMJEV-07BX-LTE Personal Mobile Alarm System

01 Getting to know your device Front Lanyard hole SOS button Personal Mobile Alarm Device Quick Start Guide Cellular GPS/Glonass WIFI BLE Side Back positioning indicator- Blue Cellular signal indicator- Green Call button Silent mode button Screw holes 02 Charging Base Loudspeaker Front Charging contacts Back Bottom The SIM card is not included in the package. A Nano SIM card is available from the user's local operator. 03 Put the SIM card 04 Charging your device There are two ways to charge your device. Microphone Power indicator-Red Charging contacts Call 1 button Voice on/off button SOS button Loudspeaker USB cable Unscrew the back cover and remove the cover. Insert the SIM card and make sure its activated with credits. Put the cover back and tighten the screws. TIP Before installing the SIM card, check if the SIM card has a PIN code or not, if yes, please use a cell-phone to remove the card's PIN code. 4.1/Charging by magnetic USB cable When placing the magnetic USB cable on the device charging contacts make sure it is posi-

tioned correctly. The power indicator (red light) should blink when charging and remain solid when fully charged. 4.2/ Charging by charging base Place the device on the charging base Connect the USB cable from charging base to the AC adaptor. The charging base light will glow when charging and turn solid when fully charged. TIP For the first time use, please fully charge the battery for around 2~3 hours TIP The charging base is equipped with a 2000mAh back up battery, which can charge the device when the electricity is off at home or when traveling. TIP When the battery level falls below 20% it will send a low battery warning message to people on the contact list via text message or APP. 01 05 Switching on and off device 06 What do the lights mean?

07 Activating an SOS Alarm 1sec. Cellular signal indicator--Green Light shows a single flash rapidly every 3 seconds Green Light shows a double flash rapidly every 3 seconds Means The device has a stable cellular signal The device is registered to the cellular network All the LEDs will flash rapidly Positioning indicator--Blue To turn on the device: press the SOS button for 1 second, all the LEDs will flash rapidly. The device can also be turned on automatically by charging via magnetic USB cable or put it into the docking station. Blue Means Blue Means Light shows a single flash rapidly every 3 seconds The device has no latest location fix Light shows a double flash rapidly every 3 seconds Light Off The device has latest location fix The device is not fixing the latest location 3sec. Power indicator--Red To turn off the device: press and hold the side button and SOS button together for 3 seconds until the LEDs turn off. Red State Red State Red ON (solid) Red shows a double flash rapidly every 3 seconds Device has been fully charged BLE connected Red Blinking Quickly Red Off or blinking slowly Battery power is lower than 20%

The device is charging 3-4sec. Press for 3-4 seconds Between each call, it will have 10 seconds delay, during this time, user can stop call sequence or prevent a possible false alarm by pressing the SOS button. The receiver of the call can also stop call sequence by pressing 1 on their mobile phone during two way talking. Use the side buttons +/- to adjust the sound volume during a call. When you need help, press the SOS button for 3-4 seconds till you hear a voice prompt of activating an SOS alarm. This starts the sequence of help me!

text message send to your emergency contact num-

bers followed by the outgoing calls. TIP Please remember to program emergency contact numbers. It is not mandatory for all ten authorized numbers to be set, however a minimum of one must always be set. If the device fails to connect to the first number, it will call the second number after delay of 10 seconds. In case the second number fails to be connected as well, the system will connect to the third number etc. TIP Please be patient during the call sequence. There can be short delays as the alarm calls phones who maybe out of range or delivered to peoples voicemail. 08 Getting a GPS fix 09 Fall down alarm 10 Making a Phone Call 11 Silent mode button To get an initial fix for the GPS features, use outdoors or near a window so the device can get a fix on the satellites. This could take few minutes according to your environment. Device detects a fall and it will automatically send an alarm to emergency contacts. To make a call, press side call button for 3 seconds and you will hear a beep, and then it will dial the second number. Hold and press this button for 2 seconds to turn off voice warnings, press 2 seconds again to turn on voice warnings. GPS 3sec. 2sec. BEEP!

Due to the daily life activities (like some sports, sit back on a coach, etc), device may detect a fall incor-

rectly, this situation may cause false alarm. However, users can manually cancel the fall alert by pressing SOS button during its beeping. TIP Very Important: Because it still has few chances for the non-detected falling down, we still strongly recommend user to press SOS button when it has emergency situation. To end the call, press the SOS button. SOS Press and hold button 3 seconds, and in the same time press CALL2 button on charging base, they will pair to each other via bluetooth. In the same time 3sec. Specification:

Dimension: 61mm*44mm*16mm Weight: 40g Battery: Rechargeable, 3.7V, 800mAh Charging voltage: 5V DC Waterproof: IP67 4 locating technologies: GPS, BLE, WIFI, LBS FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generats, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

o o o receiver is connected. o Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the Consult the dealer or an experienced radio/TV technician for help. Cautions:

Please comply with the instructions to extend the unit life:

Dont use & store the unit in dusty places. Dont put the unit in overheated or over cooled places. Clean the unit with a piece of dry cloth. Dont clean in chemicals, detergent. Dont disassemble or refit the unit. Using other batteries will cause unwanted situation. SAR Specific Absorption Rate (SAR) information:

This Personal Mobile Alarm System meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/

kg averaged over one gram of tissue. Device types: Personal Mobile Alarm System (FCC ID:

2AUMJEV-07BX-LTE) has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the product kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body and the back of the product. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. 3sec. Warning: Keep the IMEI and SIM in confidential, or your privacy may expose.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AUMJEV-07BX-LTE Label and Location Personal Mobile Alarm System Model No.: EV-07BX-LTE FCC ID : 2AUMJEV-07BX-LTE Size: L: .3.0cm*W: 1.0cm Label Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

Shenzhen Eview GPS Technology Agent Authorization Company: Shenzhen Eview GPS Technology Address: #1203 Building 2, GuoLe Technology Park, Lirong Road, Dalang, Longhua, Shenzhen, China Product Name: Personal Mobile Alarm System Trade Mark: N/A Model Number(s): EV-07BX-LTE FCC ID: 2AUMJEV-07BX-LTE We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2019-12-24 Name:

Bella Wang Title:

CEO Company: Shenzhen Eview GPS Technology

Shenzhen Eview GPS Technology Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2019-12-24 Subject; Request for Confidentiality FCC ID: 2AUMJEV-07BX-LTE To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Bella Wang Title: CEO