FCC ID: 2A2UNFBR1200 12-channel receiver

Introduction FBr12 PPX7 AFHDS3 PWM/PPM/I-BUS/S.BUS/I-BUS 2 Newport AFHDS3 FBr12 is a marine receiver, and the waterproof level is as high as PPX7, using the AFHDS3 (the third generation automatic frequency hopping digital system). It adopts the external dual antenna with the transfer back function and can output PWM/PPM/I-BUS/S.BUS/I-BUS 2 signals. It supports Newport switching, all AFHDS3 transmitters and RF heads. Receiver overview

[17]

[18]

[16]

[15]

[14]

[11]

[12]

[13]

Force update interface

[1]

[2]

[3]

[4] [5] [6] [7] [8] [9] [10]

Product specification FBr12 AFHDS3 PL18 NB4NB4 Lite PWM 12 2.4G ISM AFHDS 3 3.5 9V PWM/PPM/I-BUS/S.BUS/I-BUS 2 PPX7

-10+60 20~95 17*29*16.6mm 14g ( ) CEFCC ID:2A2UNFBR1200 Binding 1. BIND

[1]-[8] CH1-CH8

[9] CH9(NPD)

[10] Bind

[11] CH10(NPC)

[12]CH11(NPB)

[13] CH12(NPA)

[14] - /Connect to battery negative pole

[15] + /Connect to battery positive pole

[16] S /Signal pin

[17] Antenna

[18] LED Note: The performance of this product will be degraded to some extent after soaking in water. If the operations in wet environments are unavoidable, seal the antenna connector by using glue. Product Model: FBr12 Adaptive transmitter: all transmitter supporting AFHDS3 (PL18, NB4, NB4 Lite, etc.) Model Type: Car/Boat ect. PWM Channels: 12 RF: 2.4GHz ISM 2.4G Protocol: AFHDS 3 Antenna: Dual Antenna Input Power: 3.5-9V Data Output: PWM/PPM/I-BUS/S.BUS/I-BUS 2 Waterproof:PPX7 Temperature Range: -10+60 Humidity Limit: 20%-95%

Online Update: Yes Dimensions: 17*29*16.6mm Weight: 14g (Without pin header) Certifcation: CEFCC ID:2A2UNFBR1200 2. 3. 4. 5. 6. Insert the bind cable into the receivers BIND port;

Plug the power cable into any other port, and the receiver's LED will start to flash quickly indicating that it has entered bind mode. 1. 2. 3. Put the transmitter into bind mode; (See the transmitter's instruction manual for more information) 4. Binding is successful when the receiver's LED will stop flashing. Remove the power and bind cables from the receiver. 5. 6. Check to make sure that the transmitter and receiver are working as expected, if there are any issues or unexpected operation follow the Reconnect the power cable to the receiver. steps above to bind again. FBr12 Receiverhttp://www.flysky-cn.comCopyright 2021 Flysky Technology co., ltd Forced update After the transmitter is updated, if the code cannot be matched with the receiver, it is necessary to update the receiver. 1. BIND 1. Short circuit bind and its separated signal pins with bind cable;

2. LED 2. Power on the receiver to enter the update modeLED light of the receiver changes from 3 flash and 1 off, unplug the bind 3. LED 3 1 cable, and select forced update at the transmitter. 3. The LED light of the receiver changes from 3 flash and 1 off to slow flash, the update is completed. Failsafe

PWMPPMi-Bus out i-Bus 2 S.BUSi-Bus2i-bus

, The failsafe function is used to output the channel according to the out-

of-control protection value set by the user after the receiver loses its signal and is out of control to protect the model and personnel. This receiver supports three failsafe modes: "Free", "Hold", and "Fixed value"; "Free" mode refers to PWM, PPM, i-Bus out, i-Bus 2 converter entering the failsafe state keep the channel value of no output signal. The S.BUS, i-Bus2, and i-bus converters output the last received signal channel value of the transmitter. "Hold" mode means that after entering the failsafe state, keep the output of the last transmitter signal;the "Fixed value" mode means that after entering the out-of-control protection state, the set signal channel value is maintained to output the signal. Compatibility AFHDS3 PL18 1.0.55NB4 2.0.93 NB4 lite 1.0.10 3.0 The FBr12 receiver is compatible with all AFHDS 3 transmitters (Note: It is currently applicable to PL18 1.0.55NB4 2.0.93 and NB4 lite 1.0.10 and later versions. The high-frequency library used by the firmware is version 3.0.) 1 Attention:

Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury. Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation or loss of control. Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise. Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal. Do not power on the receiver during the setup process to prevent loss of control. FBr12 Receiverhttp://www.flysky-cn.comCopyright 2021 Flysky Technology co., ltd Certification FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. EU DoC Declaration Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FBr12] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at the following internet address: www.flysky-cn.com. RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. FCC ID:2A2UNFBR1200 FBr12 Receiverhttp://www.flysky-cn.comCopyright 2021 Flysky Technology co., ltd

24.7mm 21.9mm PANTONE 312C PANTONE Black 6C White 0.10 FBr12 FBr12 B-TFBR12-03 24.7*21.9mm 0.175PC+3M467 Adobe Illustrator CC 2018 20230131 01

DATE : 2023-02-17 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Jason Wu of Global United Technology Services Co., Ltd.and No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ShenZhen FLYSKY Technology Co.,Ltd and 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Signature: Name: Kyle Li Title: RD Manager Company: ShenZhen FLYSKY Technology Co.,Ltd

ShenZhen FLYSKY Technology Co.,Ltd DATE : 2023-02-17 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A2UNFBR1200 Product Name: 12-channel receiver Request for Confidentiality To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature: Name: Kyle Li Title: RD Manager

ShenZhen FLYSKY Technology Co.,Ltd Covered Equipment Certification Attestation Letter 2/17/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A2UNFBR1200 ShenZhen FLYSKY Technology Co.,Ltd certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not covered equipment. ShenZhen FLYSKY Technology Co.,Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Signed: Printed name: Kyle Li Title: RD Manager Company Name: ShenZhen FLYSKY Technology Co.,Ltd Date: 2/17/2023

ShenZhen FLYSKY Technology Co.,Ltd U.S. Agent Designation for Service of Process -

Certification Attestation Letter 2/17/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A2UNFBR1200 Per section 2.911(d)(7) of the FCC rules, ShenZhen FLYSKY Technology Co.,Ltd certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process:

Company Name: Baihetian Innovative Solutions Physical U.S. Company Address: 6837 Chase Rd, Dearborn, MI 48126, USA Contact Person: Kenneth Young Agent Email Address: ken.young@baihetiansolutions.com FRN: 0033401605 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed:

Agent Signed (if different to Applicant):

Signed:

Signed:

Printed name: Kyle Li Title: RD Manager Company Name: ShenZhen FLYSKY Technology Co.,Ltd Date: 2/17/2023 Printed name: Kenneth Young Title: Manager Company Name: Baihetian Innovative Solutions Date: 2/7/2023

*the applicant must designate a contact located in the United States for purposes of acting as the applicants agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process.