User Manual FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. MOZA AirCross 3 Overview 1 2 3 4 5 6 7 16 17 18 1. Tilt Motor Lock 2. Extension Port 3. Quick Release Plate 4. Tilt Adjustment Slider 5. Pan Motor Lock 6. Foldable Safety Lock 7. Smart Trigger 8. Quick Release Plate Knob 9. Quick Release Baseplate Knob 10. Roll Knob 11. Roll Motor Lock 12. Pan Knob 13. USB-C Charging Port 14. Battery Indicator Light 15. Power Button 8 9 10 11 12 13 14 15 19 20 21 16. OLED Screen 17. Joystick 18. 1/4 Extension Port 19. Camera Control Port 20. AI Extension Port 21. Tilt Knob 22. Foldable Knob 23. Camera Control Button 24. Function Button 22 23 24 1 Preparation Unfold the Gimbal 1.Rotate the foldable Knob;
2. Unfold the handle until it is locked. 3. Tighten the knob to prevent the handle from loosening. Attaching the Tripod 1. Screw the mini tripod into the screw hole at the bottom of the handle. 2. Expand the mini tripod Battery Charging Please charge the battery through the USB-C charging port using a USB-C cable
(Included) and a USB adapter (Not included). It is recommended to use a USB adapter with QC2.0 or PD protocol to complete the charging quickly. The LED light below the charging port will switch off after the charging is completed. USB-C Port USB Type-C Cable 2 Unlock the Gimbal Rotate the motor lock to the unlocked position, and then each motor can rotate freely. Note: Do not rotate the motor before unlocking, otherwise the motor lock may be damaged. If the gimbal is turned on before unlocking, the gimbal will enter sleep mode. Mounting the Camera Make sure to prepare the camera before mounting, confirm the battery is fully charged and a memory card with sufficient storage space is inserted. 1. Place the camera on the quick release plate with 1/4or 3/8screws and keep the camera in the center. Remove the extra screws as a spare. 2. Slide the quick release plate onto the baseplate to the locked position. 3. Secure the quick release plate and tighten the knob, make sure the quick release plate is locked. 3 Note:
a. When installing the camera, if the right side of the camera interferes with the tilt arm caused the installation to fail, loosen the knob of the quick-release baseplate and move it to the left until the camera can be installed successfully. b. After the camera is installed, move the quick-re-
lease baseplate to the right and make sure the camera's right side is aligned with the tilt arm to achieve the best stability. Balance Adjustment 1. Balancing the tilt axis vertical a. Rotate the camera so that the lens is pointing upward b. Unlock the tilt axis and loosen the knob, slightly adjust the position of the tilt adjustment slider. c. The balancing is completed when the camera is steady while pointing upward, lock the tilt axis. 2. Balancing the tilt axis horizontal a. Rotate the camera so that the lens is pointing forward;
b. Unlock the quick release plate, slightly adjust the position of the plate;
c. The balancing is completed when the camera is steady while pointing forward, lock the quick release plate. 4 3. Balancing the Roll Axis a. Unlock the Roll axis. b. Slightly adjust the roll arm left and right until its completely horizontal. c. Lock the roll axis. 4. Balancing the Pan Axis a. Hold the gimbal at an angle of 45 horizontally, turn the pan arm to a horizontal angle. b. Unlock the Pan axis and slightly adjust the pan arm left and right. c. The Pan axis is balanced when the camera is steady, lock the pan axis. Operation Power Button Long Press: Power on or off One Click: Switch the follow speed, 5 levels from slow to fast Double-click Enter or exit sleep mode. Joystick Control the rotation of the gimbal Menu:
Top Button: Option-up Down Button: Option-down Left Button: Return Right Button: Confirm 5 Camera Control Button Press halfway: Autofocus One click Press and hold for 3 seconds: take a photo Start recording Function Button:
One Click: Follow mode(Pan-Tilt Follow, All Lock) Double Click: Sport Gear Mode Triple Click: Inception Mode Long Press: Enter/Exit Menu Trigger Button One Click: Start/Stop AI Follow Mode Double Click: Re-center Triple Click: Selfie Mode Press and Hold: All Lock One Click and Hold: Pan-tilt Follow Please visit www.gudsen.com for the complete user manual. It will guide you:
Advanced Features Language Switch Camera Control Button Customization Motor Output FPV, Sport Gear Mode, Manual Positioning User Configuration Calibration and Firmware Updates MOZA Master App Scan the code or search in the app store to download the MOZA Master App. MOZA Master provides functions like Virtual Joystick Control, Motion Sensing Control, Parameter settings, Time-Lapse, Panorama, Calibration and Firmware Updates. iOS Android 6 Specifications Model: AirCross 3 Weight: 1.3kg without tripod Dimension: Unfold: 170*190*310mm,
(W*D*H) folded: 52*225*270mm Battery Capacity: 3400mAh Standard Votage: 7.27V Charging Votage: 5V/2A, 9V/2A Working hours: 20H Fast-charging time: 1.4H Battery Type: Li-ion Intelligent Battery(built-in), 24.718Wh Bluetooth: BT5.0 2.400 GHz -2.4835 GHz Environmental requirements:
Working temperature: -10 Charging temperature: 5
-50
-40
Safety Caution 1. This product is powered by a built-in battery; please do not disassemble it, do not put it into liquid or fire in order to avoid damage or risk of injury. 2. Before powering on the gimbal, please adjust the balance follow the instructions in this document. If the gimbal works in an unbalanced state for a long time, the surface temperature of the motor can get hot, which will seriously shorten the battery life. 3. Do not let children touch and use this product, do not use fingers to obstruct the motor operation to avoid finger injury. 4. This product is not waterproof or dustproof; please keep the gimbal clear of dust and water to avoid damage. 7 AirCross 3 1 2 3 4 5 6 7 16 17 18 8 9 10 11 12 13 14 15 19 20 21 22 23 24 8 9 10 11 12 MOZA Master iOS Android 13 14 Shenzhen Gudsen Technology Co., Ltd