EN......................................................................................................................................1 CH......................................................................................................................................7 Battery and Charging The MOZA Slypod comes with a built-in lithium battery. When charging for the first time, please fully charge the Slypod to activate the battery. Solid red indicates the Slypod is under charging, solid blue indicates the charging is completed. With a Type-C interface, the Slypod is able to be charged by a mobile phone charger or external power bank. It will automatically stop charging when the battery is full. Note:
1. Its recommended to use the original charging cable provided in the package!
2. Do not overcharge or over-discharge the battery, otherwise the battery cell will 3. If the battery is idle for a long time, please recharge and discharge it every 3 be damaged. months to keep it active. MOZA Slypod Overview Pan-tilt Head Pan-Tilt Lock Tilt Knob Screw Pan Knob Screw Quick Mounting Port Adapter
(accessory) 1/4 Extension Hole Quick Mounting Port Handle 1/4 Screw Hole 3/8 Screw Hole 1 Arca-Swiss Quick Release 1/4 and 3/8 Extension Hole Quick Release Screw Quick Mounting Port Indicator Light Power Button Operation Button Charging Port Mounting Mounting the handle Align the 1/4 screw hole on the handle with the 1/4 screw on the bottom of the pole, turn the handle clockwise to tighten it. Mounting the pan-tilt head Slide the pan-tilt head into the groove at the top of the pole, make part 1 and part 2 fully fit. Turn the screw ring 3 clockwise to secure the head onto the pole. Loosen the screw ring 3, then turn the knob screw 4 anticlockwise to detach the head from the pole. After the P&T head is detached,reset the quick release knob.
(Mounting the adaptor) The same method as mounting the pan-tilt head. 2 Getting Started Long press for 3 seconds: Power on/off Button Functions Power Button Device State Elongate+
Shorten-
Short press Long press Photo taking control via the shutter cable Static Start to elongate Start to shorten Elongate Accelerate by one gear Decelerate by one gear Shortened Decelerate by one gear Accelerate by one gear Short press power/+/- buttons(all three buttons) at the same time: Reset Power on Static Elongate and continue to accelerate Elongate Accelerate Continuously Shortened Accelerate continuously to an elongate state Shorten and continue to accelerate Decelerate continuously to an shortened state Accelerate Continuously Long press +/- button at the same time: Automatic reciprocating mode(The blue light lasts for 1s indicate a mode switch.) Double Press Triple Press Stop Turn Off + Reset
(Blinking red) App Download Scan the QR code or search in the App Store to download the MOZA Master App.(Please find the QR code at the end of the Manual.) IOS Android Device Connection (Wireless) Download the "MOZA Master" App. Turn on the phone Bluetooth and Slypod. Launch the "MOZA Master", select the device to connect. Enter the operation interface after connection is completed. 3 App Operation Note: It's required to active the device according to instructions before the first operation. please download the latest version. Updates are subject to change without notice. please note the major application stores Slide the operation point to any position, the device will move according to the sliding path. Maximum extension length Movement distance Long press: movingup Release: stop moving Long press: moving down Release: stop moving Moving speed setting Segmentation Mode Select the segmentation mode, add a path (Tap to add path,5 paths can be added in maximum), and then slide the path bar to any location. Set the running time of each path separately. Tap to start and the device will move according to the set path and speed. Path number Moving up Moving down Reset path The Beginning
(number show s the distance from the origin) Tap to the red area to set the running End (number shows the distance from the origin) Tap to start running 4 Tap to reset Tap to add path Path running time setting Tap Confirm to complete setting Step Time-lapse Select step mode to set step length, cycle, residence time and step movement time. After the setting is completed, tap Start and the device will move according to the set step length, speed and cycle. Solid red Solid blue Solid green Firmware Upgrade In the charging state, enter the APP interface after the device is connected to the APP, and select the Firmware Upgrade to perform the upgrading. The device must be restarted after the upgrade succeeds. If the upgrade fails, the process needs to be repeated until the upgrade succeeds. Status Indicator Charging Charging completed Power on Under-voltage alarm Low voltage alarm Blinking green for 1s Blinking blue for 1s Charging Uncover the rubber sleeve over the charging port, the Type-C interface is inside. The Slypod can be charged by mobile phone charger, mobile power bank, etc. It will automatically stop charging when the battery is full, please disconnect the charger then.
(It is recommended to use the original charging cable provided in the package) Solid orange Blinking red + automatic reset &shutdown
(blinking red, unable to power on while pressing the power button) Start/stop running switch Testing/operating modes switch 5 Specifications Size Weight Payload Operating speed Slypod Storage Length:522mmgrip not included Expanded Length:971mm Max Diameter:54mm Main Body: 745g PTZ Head: 287g Grip:278g Vertical:9kg Horizontal:4Kg Highest:28mm/s Lowest:0.15mm/s 120min Operating Voltage 8.5v - 12.6v Battery Life Working Temperature -10 - 50 Communication Interface Bluetooth 2.4G Type-C Lithium ion Battery 600mA/h 11.1V Type-C USB 5V 90min Battery Model Battery Capacity Battery Voltage Charging Port Charging Voltage Charging Time 6 FCC Warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. SlypodSlypod SlypodType-C Slypod 1.Slypod 2. 3.3 7