FCC ID: 2A8HI-GC561622 All-In-One Touch Screen

LCD Touch AIO Users Manual P/N: 4.80.01.1047-0501 VER 1.0

http://www.donviewware.com 400 001 8522

LCD Touch AIO XVI. Faults and Troubleshooting No power No picture Poor receiving quality Clear picture sound

, but no Good sound, but poor color Snowflake in picture and noise illusion Ghost or no response of remote controller

, Screen is too bright

or dark PC mode Check if AC power wire of this Product is well inserted into power socket. However, if it still has no power, unplug the power plug and wait for 60s before reinsert it, then start the machine. Check the connection of antenna at rear side of machine and try other channels. Ghost or illusion may occur if there are high buildings or mountains nearby and in such case, you may manually adjust the picture quality:please refer to introduction in manual searching or change the receiving direction of external antenna. If indoor antenna is used,it may have difficult receiving in some cases. The picture quality can be improved by changing the antenna direction. However,if poor picture quality still exists, please use an outdoor antenna. Increase volume,check if the machine is controller to cancel mute. mute and press Mute button on remote Increase contrast and brightness. Check connection of antenna at rear side. It may be caused by poor antenna position.Picture quality can be by using high directional antenna;the remote controller should correspond to remote control sensor on the machine. If theres no reaction,check if the plastic isolation paper is removed and if batteries are correctly installed, and replace the batteries. If this machine fails to receive signal within min it will be switched to pause state. auto-matically improved 15 Adjust contrast and brightness in main menu

. XVII. Notice for Waste Recycling If this Product is no longer needed or reaches its service life

, submitted to the qualified recycling pants recognized by state in accordance with the relevant laws and regulations for recycling of waste electric pro-

ducts in order to care and protect our earth shall be

~23 LCD Touch AIO

LCD Touch AIO Contents XV. Product Upgrade & Maintenance Introduction to product upgrade and module replacement System upgrade Online upgrade such upgrade shall be compatible to the current storage space shall be reserved for downloading and installation

. AIO and version and enough

TV Local upgrade the upgrade package which is from existing external device directory and

, resources is used for local upgrade 1 Upgrade of software module:during software upgrade,the user may select upgrade of compatible to this Module replacement

. materials

. the 2 Upgrade of hardware module if hardware has fault or new functions are needed user may make application to manufacturer for replacement of following modules interface module,power module infrared emission receiving module ops computer module and Android module Product maintenance simulation and question bank module

, MUST Way to keep screen clear to power off and unplug power wire before start of cleaning add small amount of softening agent or detergentin water Early faults can be prevented and service life of machine can be prolonged by carefully

. screen has excessive water on it make sure it is fully dried before starting the and regularly cleaning .It is a Screen cleaning 1. wet the soft cloth in water and have it dried and then wipe the screen

. 2 If

. machine Shell cleaning 1 Please clean the dirt or dust on shell using soft,dry and hairless cloth It is not allowed to use wet cloth

. further damaged caused by lightning or electric wave

. kindly consult local maintenance person Maintenance instructions

. 2 Warranty period of other accessories 1year. 3 Software enjoys life long free upgrade 3 This Product shall be disassembled by professional staff only .For any problem please 2 Please unplug the power plug before this machine is idled for certain period to prevent 1 Warranty period of entire machine 3years.

, VII. Introduction to Quick Use

...................................................... I Outline Drawing

............................................................... II. Brief Introduction to External Labels

............................................... III. Notice for Operation

........................................................... 2 2 3 IV. Safety Notice - Warning

......................................................... V. Safety Notice - Caution

.......................................................... 4 5 VI. Introduction to Product Operation and Maintenance

................ .................. 6 7 8 VIII. Control Panel

............................................................... IX. Introduction to Ports at Rear Side

................................................. X. Introduction to Menu Operation

.................................................. 10 11 XI. Use of Android System

......................................................... 12 XII. Installation of Electric Whiteboard in Computer System

............................... 20 XIII. Drive Installation

.......................................................... XIV. AIO Positioning

............................................................ XV. Product Upgrade & Maintenance

................................................. XVI. Faults and Troubleshooting

.................................................... XVII. Notice for Waste Recycling

................................................... 20 20 22 23 23

~22

~ ~1 LCD Touch AIO LCD Touch AIO I. Outline Drawing

(For illustrative purposes only and may differ from the actual product) 1?Display and Replacement of Current Series 2?Positioning Click Current seriesand choose AIO series ; then click Enable device button;after connection is done the window will be changed

as shown in the left figure

, II. Brief Introduction to External Labels Warning Please assemble, use and maintain this roduct in strict accordance with regula-

tions below to keep safety since electric shock or fire hazard may be incurred by impro-

per operations,even if we have attached much attention to personal safety in design and manufacturing stage. Please carefully read the safety instructions below before using it. P Warning: This Product is highly sensitive!

Please keep it away from rainwater or humidity to keep out electric leakage or fire alarm. Never open shell without permission; otherwise, electric shock may be incurred by high-voltage wire inside. RSK ELSCTRIC SHOCK Click Device positioning button or click service program icon select Positioningoption to pop up the window as shown in the left figure

, Click one positioning mode to enter the positioning of electric whiteboard.

<As shown in the left figure>

, Please click the center of positioning cursor using whiteboard pen the green light circle will gradually become orange;

when entire circle becomes orange the positioning is finished and positioning cursor will be automatically moved to the next point

as shown in the left figure

, Repeat the above action,until the positioning of all points is finished. 3 Shortcut Configuration ClickConfiguration button to change corresponding functions of shortcuts of

. 4 Exit Server Program ClickDisable button to exit disappear. 5 Enable Whiteboard at Startup TickEnable device at startup to automatically connect gram at the next startup AIO

. the server program and the tray icon of system will and enable service pro-

AIO

~ ~2

~21 LCD Touch AIO LCD Touch AIO XII. Installation of Electric Whiteboard in Computer System

. 1 Introduction to installation of electric whiteboard software CD WhiteBoard electric whiteboard software includes 2 CD

Electric whiteboard software Junior version) applicable to kindergarten and

This mark reminds users to correctly use this Product in accordance with the Users Manual to keep safety. junior schools;

Electric whiteboard senior high 2 Key notices in installation

software general version) applicable to junior high school school vocational school colleges and universities and other industries

. FCC Warning Note:if software is blocked by antivirus software or firewall during installation,

, please select Allow all operations of program and tick Remember my choice no more prompt;otherwise,it may lead to installation failure or software installa-

tion cannot be normally used. 3 Installation interface of electric whiteboard Put electric whiteboard CD in the drive of computer and it will have auto run and pop up the interface below:

Note: if the interface above is not popped up automatically,please click the autorun hta application program in CD to pop up it

. XIII. Drive Installation No drive is needed to be installed for XIV. AIO Positioning this LCD AIO

. Once the electric whiteboard software is installed it will generate Device

and double click to open it as shown in the right positioning icon on desk figure

, III. Notice for Users 1.Recommended distance for comfort viewing The best distance for viewing shall be 5-7 times of that of screen height. 2.Height & angle Appropriate viewing height and angle can help get you rid of an easy fatigue. 3.Volume Please keep proper volume to keep out interference to others(at night,in particular). 4.Ambient brightness Your eyes may suffer from an easy fatigue in case of direct sunlight to screen,ex-

cessive brightness or darkness of room, intense darkness without light around, or fluorescent screen has reflected light. So, please keep soft and indirect lighting, instead of direct sunlight on screen. The brightness sufficient for reading newspa-

per shall be the best. 5.Adequate rest It is highly recommended that you take a periodic rest, even if this Product has neither blink nor harm from radiation by using LED technique.

~20

~ ~3 LCD Touch AIO LCD Touch AIO

. 6 Operation of remote controller Never cover receiving window of remote controller or expose it to strong sunlight to keep good receiving sensitivity. RSK ELSCTRIC SHOCK 7. Notices for dry cells of remote controller The service life of dry cells is around 1 year (depending on your frequency of use). In case remote controller is faced with short operation distance and low flexibility, please replace both old cells of it. mixed use of new and old cells, or dry cells of different types is not allowed;

Note:

otherwise, the remote controller can be damaged by liquid leakage.Please take out dry cells of a remote controller to be long idled. In case liquid leakage occurred, please firstly clean up the liquid in cell box before installing the new cells. 8. Way of handling Please firstly uplift this Product before handling. Make sure this Product is handled by at least two persons to keep its stability and protect shell. Do not scratch the screen during the handling. 9. Condensation If this Product is moved from cold to warm place quickly, or from room with elec-

tric heater to other places, this Product may have puzzled interface, failed color display at certain images,or uneven color,all of which are caused by condensation in machine. The image can be recovered after volatilization of steam. IV. Safety Notice - Warning 4.1 Immediately shut off the power supply and unplug the socket in case of any smoke, and consult the dealer at once . Fire hazard or electric shock may occur if continuing using it. 4.4 Never plug in/out the power socket by wet hands to keep out electric shock. 4.2 If screen has no output of image or audio, please immediately power off this Product and unplug the power socket. If such fault occurs suddenly at normal state, please do not keep using this Product,but consult the dealer. 4.3 If this Product falls onto ground acciden-

tally or shell is damaged,please immediately power off this Product and unplug the power socket.Please do not keep using this Product, but consult the dealer, to keep out fire hazard or electric shock. 4.5 Keep power socket free from accumulated dust to avoid degrading insulation performance of plug. Please regularly clean the dust to keep out a fire hazard. 4.6 Do not maintain,transform or disassemble this Product without permission;otherwise, electric shock,fire hazard or damage of internal parts may occur since this Product contains

.For details high-voltage and fragile articles of maintenance, Letter of please refer to the Guarantee and consult the dealer. Please use the Whiteboard pen to vertically tap the center of the positioning cursor. Now the green light circle grades into orange. When the entire circle turns orange, the positioning of the point is finished,and the positioning cursor will automatically move to the next point, as shown below. Repeat the above action until all points are positioned. 7.2.Shortcuts setting (This series products not hot key) On the Android OS, not all the shortcuts on the left and right sides of the integrated machine are enabled. The shortcuts that are enabled are:1 Switch mode, 2 Collapse toolbar, 3 New page, 4 Page up, 5 Page down, 6 Blue pen, 7 Red pen, 8 Black pen, 9 Highlighter, 10 Smart pen, 11 Eraser, 12 Undo, 13 Clear screen, 14 Text pen, 16 Open file 1) Disable shortcuts The default status of shortcuts is enabled. After Disable shortcuts is checked, the shortcuts function on the Android OS is not available. After it is unchecked, the shortcuts function is restored. (This series products default option "Cancel HotKey")

(Shortcuts are disabled if checked) 2) Flip Whiteboard If the function of Whiteboard flipping is enabled by service program on the Windows OS, shortcuts will be disabled on the Android OS, meaning it is also required to check Flip whiteboard on the Android OS . 8.About It displays software version and copyright information.

~ ~4

~19 LCD Touch AIO LCD Touch AIO 5.Settings and about 5.1 Main toolbar settings The user can customize the main toolbar icons by tapping Settings Icon Settings to open the main toolbar icon settings window, as shown below:

-Main Toolbar The upper part of the window (boxed rectangle) indicates the icons currently displayed on the main toolbar, and the lower part (boxed oval) indicates the icons that can be added to the main toolbar. Removing a main toolbar icon:Tap the icon displayed on the main toolbar to remove it. Tap the Finish button after setting. Add a main toolbar icon: Tap the icon to be added in the lower part, and the icon will be selected and its function will be displayed at the bottom of the window. Tap again while it is selected and it will be moved to the main toolbar display area.Tap the Finishbutton after setting.After icon adding or removing,tap theRestore Defaults t button to restore the main toolbar to its default state.Alternatively,long press the firs icon on the main toolbar, and tap OK in the pop-up Restore Defaults dialog box. 6.Open Eshare receiver After the Eshare receiver is installed on the Android OS of AIO, youcan quickly open Eshare application with the button . If the Eshare software is not installed, the following prompt appears:

7.Positioning and shortcuts positioning 7.1 Positioning For touch position correction on the Android OS, tap Settings - Positioning to offer options of 4-point positioning,5-point positioning,9-point positioning and 16 points positioning. After one of the positioning option is selected,it will jump to the positioning screen,as shown below. P 4.7 Keep this roduct free from long contact with rubber to protect this Product against shell metamorphism or coating peeling. 4.8 This Product is applicable to 220VAC power socket only. Never use this Product out of rated voltage (220VAC); otherwise, fire hazard or electric shock may occur. 4.9 In case of thunder or lightning, please do not touch antenna or power wire , but immediately unplug the power socket,so as to keep out electric shock. 4.10 Never place this roduct in places with P high temperature or direct sunlight to keep out abnormal temperature rise and fire hazard. 4.11 It is strongly recommended that you share wall-mounted plug to extension wire and other power consumption goods and, if it is inevitable,please check if its rated vol-

tage is sufficient;otherwise,a fire hazard may occur if extension wire has excessive load. 4.12 Never place vase,flowerpot,glassware, cosmetic,chemical containers,liquid or small metal object on this Product to keep out fire hazard or electric shock if liquid or small object falls into it, and if it occurs, please immediately power off this Product and unplug the power socket, and consult the dealer. 4.13Please well protect this Product against foreign matters to prevent fire hazard or electric shock. However, if foreign matters are found in it,please immediately power off this Product and unplug the power socket, and consult the dealer. Much attention shall be attached to preventing children from putting foreign matters in this Product. 4.14 Never expose this Product to oil,smoke and vapor, or near heater or dusty place to avoid degrading the image quality,fire hazard or electric shock. V. Safety Notice - Caution 5.1 Never block the ventilation hole of this Product, put screen face upwards, laterally or invert it.Never put this Product in poorly ventilated place,such as closet or bookshelf. The distance between machine and wall should be over cm. ever put this Product N on carpet or flammable staffs, or cover it using curtain or tablecloth to keep out a fire hazard. 15 5.2 This Product shall be installed in stable place with good ventilation. 5.3 Never put heavy objects on this Product to prevent unstable center of gravity,inver-

ting this Product or hazards by falling of heavy objects.

~18

~5~

LCD Touch AIO LCD Touch AIO 5.4 This Product shall be handled by at least two persons.It is needed to unplugthe power wire plug,remove antenna and other devices before handling . It shall be handled with caution to avoid impact or screen damage. 5.5 Never stand or sit on this Product. For family with children,much attention shall be from climb-

attached to ing or displacement, overturning, damage or other injuries. preventing children playing the to avoid TV 5.6 Never disassemble the rear cover, shell panel or any other cover to avoid electric shock due to high-voltage parts inside.Please consult the dealer for any adjustment or maintenance. P 5.7 Never put this roduct or power wire near the heater to keep out a fire hazard,since the surface of shell or power wire may have deformation and melting if being heated. 5.8 Please firstly unplug the power plug of motor before cleaning or maintenance other-

wise, an electric shock may occur. Please clean the screen using soft clothes to avoid scratching it (see maintenance chapter).

5.9 Never cut, twist, bundle , transform or bend the conduct,or pull it with much force during operation, or put anything heavy on power wire;otherwise,fire hazard and elec-

tric chock may occur due to damage of power wire.If power wire is damaged, please con-

sult the dealer.

Open the saved.donv file,tapped to pop up the file selection window (showing all the Android directories by default),where the user can tap the default path to go directly to the the Board install path, or select the USB path, or other local Android path, as shown below. Save current page as .png picture, automatically name after the machines

time, and the picture can be viewed in the gallery. current

Save all pages as .donv file, tapped to pop up the file saving window (showing all the Android directories by default),where the files are automatically named after the machines current time,and the user can tap the default path to go directly to the path to install the Board, or select the USB path, or other local Android path, as shown below. Note: Uninstalling and reinstalling the WhiteBoard software will automatically delete all files in the installation directory. If the files are saved in the default path, uninstalling and reinstalling the software will delete the previously saved files. If you dont want the files to be deleted, you can choose to save them in the other local Android path. 5.10 While unplugging the power plug,make sure to grasp the plug,instead of pulling the power wire, since it may damage the power wire and cause a fire hazard or electric shock. ever place this 5.11 N roduct in a shocking, P tilted or unstable place;otherwise, this ro-P duct may be falling or overturned and thus leading to an injury or damage. 5.12 If this Product is to be long idled if you are in travelling or business trip, please un-

plug the power plug to keep out a fire hazard due to degraded insulation performance of power wire. VI. Introduction to Product Operation and Maintenance wipe off the dust on surface using 1. Daily maintenance of touch screen 1) Gently buckskin or high-grade glass cloth. 2) Fingerprint on touch screen of AIO shall be cleaned using specific detergent for LCD electronic whiteboard screen.While clean-

ing this Product using detergent,please wipe it from the center to the surroundings until the detergent is fully cleaned. 3) In no way should water flow into the in-

terface between electric whiteboard screen and framework to a void burning the display due to short circuit. 4) Never wipe the electric whiteboard screen using hard towel to avoid affecting the dis-

play effects due to fluffing. 5) Stubborn oil dirt may be removed by pasting transparent tape on screen and then removing it.

~6~

~17~

LCD Touch AIO LCD Touch AIO

: Blue,red and black pens,which can be tapped to quickly switch the pen colors.

: Pen color settings, which offer various color options and take effect after the color is selected,the brightness is adjusted and OK is tapped.

: Pen size, including 5, 20, and 50.

: Pen size settings, which offer sizes 1-80.

: Curve,which allows a switch from Draw status to Annotate status without changing the solid or dashed line setting of the pen.

: Straight line, selected to keep drawing straight lines.

: Text, selected to add an input box when tapping on the whiteboard page,where you can input text;you can do it all over again after each input.

: More graphics, including circle, triangle, and rectangle.

: Circle, selected to keep drawing circles. riangle, selected to keep drawing triangles by tapping on three T

points on the page.

: Rectangle, selected to keep drawing rectangles. 4.2.1 Page features WhiteBoard for Android provides various page operations, including creating a new page,setting page color, undo and redo,page up/down,page clearing,page preview, saving picture, saving file, and opening saved file. The corresponding icons are as follows:

: Undo the last action on the page.

: Redo the undone action.

: Page up.

: Page down.

: Clear page, which allows clearing of all the annotations (including graphics and texts) on the page by one tap.

: New page, which allows creations of a new blank page.

: Set page color,which offers convenient colors,such as transparent,white,black, green,blue,red and yellow,provides multi-color settings,and allows users to customize background color, and adjust brightness and transparency.

. LCD LCD

. 2 Daily maintenance of display 1) It is needed to turn off the display or reduce the brightness if it is idled;otherwise, the display may be burnt due to burning or aging of internal parts after longterm opera-

tion.Besides,certain pixel may be over-

LCD heated and further lead to internal burning if the LCD has longterm and continuous dis-

play of certain content.Therefore,it is needed to turn off the screen or screen saver if it is idled, or display all white contents of electric whiteboard screen. 2) Unnecessary vibration shall be pre-

are highly sen-

vented: spare parts of sitive and accurate and screen may be da-

maged due to strong vibration. 3. Introduction to daily operation:

1) Maintain humidity of environment at a certain degree 2) Its needed to start,stop and operate this Product correctly in order to protect data and prolong the service life of it. 3) It is needed to start/stop this Product in strict accordance with the sequence;firstly turn on the screen before starting computer;

and firstly turn off the computer before stopp-

ing the Product;power off until the indicator lamp of computer and screen is off. 4) It is forbidden to write or draw on the touch infrared frames at four edges, or da-

mages the infrared frame using any objects besides,its needed clean the dust on them on a regular basis to avoid affecting the infrared touch function. 5) Electric products shall be free from humid,shocking and unstable position. Statement: this Product may realize zero energy consumption only if it has no connec-

tion to external input power supply. VII. Introduction to Quick Use 1Introduction to startup & shut-

down of the AIO

)1 Make sure power wire is well connected

(power socket of AIO is connected to the left or right side of screen)and power supply is safe.

)2 Press the power switch which faces downwards at the left side(or right side)and now,the remote control receiving window at should be red, the lower right corner of is ready to be started. which means,the AIO AIO POWER e power button on remote controller

)3 Th has the same function with button at lower right corner of screen.If the remote control receiving window at lower right corner of screen becomes red,pressPOWER button or power button on remote controller, the remote control receiving window will become orange and enter startup picture at the same time.If AIO has computer,it will be automatically started several minutes after start of screen. 4The user may have other operations after successful startup of the 5 If this Product is under startup state, the user may click button at lower POWER right corner of screen, or power button on remote controller to pop up the prompt of whether shut down on screen;Select to turn off screen and computer; the remote control receiving window becomes red and AIO enters standby state. 6 If this Product is under standby state, turn off the downward power switch at the left side (or right side), the remote control receiving window at lower right corner of AIO is off and AIO has normal shutdown. Yes

.AIO ress Signal Sourcebutton on remote 2Quick use of remote controller 1 Reverse the remote controller, install two AAA alkaline batteries and close the cover of battery bin. never use rechargeable batteries such Note:

as nickelcadmium battery to ensure correct operation , since such batteries may have different shapes and performance.The waste batteries shall be disposed in an environmen-

tally friendly way. 2 P controller to quickly switch to the channel needed, including and HDMI 3 For detailed functions of remote con-

troller,please refer to Article X of this Manual Introduction to se of emote ontroller. 3Operation method for external PC of the AIO There are three operation methods of ex-

ternal wire( self prepared ); connection via HDMI wire ( accessory or self prepared). by using p, own and U D

: connection via YPbPr ,VGA key. VGA and AV of AIO OK PC U C R

~16

~ ~7 LCD Touch AIO LCD Touch AIO

.PC AIO USB USB VGA VGA

,and onnect to the wire to wire end to the end at left side of VGA of end of connect flat end port(touch is available if

(or right side) AIO

. PC TOUCH In the first method, it should be con-

nected through the following steps:

1)C out-

put port at left side connect another end to 2)Connect the end of USB of USB this end is connected) of external In the second method, it should be connected through the following steps:

1)Connect port at front side of AIO, end to port of external HDMI 2)Connect the flat port of TOUCH-USB port at front of another flat port to external is available if this end is connected). In the third method , it should be connected through the following steps:

1)Connect ward HDMI connect another end to ternal PC. HDMI port at left side of wire to and connect port(touch

. PC USB

, AIO USB

, and port of ex-

wire end to the down-

and connect another wire end to the HDMI HDMI HDMI AIO 2)Connect the square opening of wire to the TOUCH-USB

,and connect the flat side of AIO the PC USB ble if this end is connected) port of external port at left side of port to USB

(touch is availa-

USB Suggestion:

HDMI interface at front panel wire 3m;

is connected to T HDMI interface at lateral side is connected to HDMI wire 5m. HDMI he After wiring is finished, you may switch the screen of external to the screen of PC for display and touch operation.Now, AIO t whitebo-

he user may write and mark using ard software of external PC. For details about installation and operation of whit-

eboard software,please refer to detailed introduction to installation and operation of whiteboard software in this Manual. Note: For any inconsistency between the real object and introduction in this Manual, the real object shall prevail. 3.Starting program Tap the application icon (for a infrared LCD integrated machine, tap the home icon or the shortcut toolbar icon) to open the software, and the main toolbar appears on the left side of the screen. Now annotating is available on the current Android screen. 4.Basic operation 4.1 Switching status 1) Desktop status and Annotate status After opening the software,the default status is Annotate,which allows such opera-

tions as annotating and drawing.In the Annotate status,tap the first toolbar icon to switch to the Desktop status. The Desktop status allows to operate other applications on the desktop.Tap the float-

ing icon in the upper left corner to switch to Annotate status. 2) Collapsed status and Expanded status In the Annotate status, the toolbar is expanded by default. Tap the second toolbar icon to switch to Collapsed status. Now the toolbar remains in Annotate status before it is collapsed. When the toolbar is in Collapsed or Expanded status, long press icon to move the toolbar. 4.2 Closing software Tap the last toolbar icon to close the software. Before it is closed the prompt Do you need to save the file? pops up. Tap Cancel to quit exiting the whiteboard software, tap Yes to save the annotations and exit the software, and tap No to exit the software without saving the annotations. VIII. Control Panel

(for illustrative purposes only and may differ from the actual product) Left Control Panel Right Control Panel

~ ~8 4.2 Main features 4.2.1 Annotation features Tap the annotation pen icon on the toolbar to quickly select a pen status for an-

notation; tap the pen setting icon to set the annotation pen. The pen setting fea-

tures are as follows:

: Annotation pen, which, despite attributes that are set, once tapped becomes a red pen with font size5, solid line, and curve.

: Eraser, which is divided into large, medium and small sizes, and can be used to erase annotations, graphics, and texts.

: Solid line,which once switched from dashed line can be used for annotating or drawing.

can be used for annotating or drawing. Dashed line,which once switched from solid line

~15 LCD Touch AIO LCD Touch AIO 5Use of Whiteboard Software in Android System Left control panel WhiteBoard for Android is a practical software installed on the Android integrates such features as annotating,drawing, saving picture and saving annotation. It is easy to operate with simple icons, and allows commenting on the Android OS.

,which OS USB USB USB TOUCH HDMI TYPE-C 1 Operating environment WhiteBoard for Android supports Android 5.0 and higher. 2 Software installation On the Android OS, tap on the .apk file of WhiteBoard for installation, and the following screen will appear. Tap Install in the lower right corner, and tap Finish or Open after installation is done. S/N 1 2 3 4 5 6 Port Name USB3.0 USB 3.0 USB3.0 TOUCH HDMI TYPE-C Right control panel Function USB interface on TV/Android/OPS system(Public USB3.0) USB interface on TV/Android/OPS system(Public USB3.0) USB interface on TV/Android/OPS system(Public USB3.0) USB interface for HDMI1 T ouch connection HDMI wiring interface

(HDMI wire 3m recommended)

TYPE-C interface U S B + V I D E O + A u d i o + c h a r g e ( 5 V / 3 A )

(Public USB3.0) CH CH Port Name S/N 1 and MENU CH- and CH

SOURCE 2 3 4 5 6 7 8 Function Menu button to switch between Android and Window Volume regulation button. Press button on screen menu to adjust volume and adjust volume in other sub menus. Switch button to display menu on screen Press CH- to confirm entering sub menu, press CH- &

CH+ to select sub menu, select signal source; or to select channel in TV mode. To switch signal source Power switch Remote control receiving window Light-sensitive receiving window

~9~

~14 LCD Touch AIO LCD Touch AIO IX. Introduction to Ports at Rear Side 4Use of floating menu TYPE-C RS232 Earphone RJ45 Out RJ45 In COAX OUT DP TOUCH DP S/N S/N 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 Port Name Port Name TYPE-C RS232 Function Function TYPE-C interface on TV/Android/OPS system(Public USB3.0) RS232 interface (serial port) Earphone out Earphone interface RJ45 OUT RJ45 IN COAX OUT TOUCH DP Cable output interface Cable input interface Optical audio output USB interface for DP touch connection Display Port input port(DP wire 3m recommended) HDMI 2 HDMI 1 HDMI TOUCH HDMI OUT TYPE-C MIC USB 2.0 (A) USB 3.0 USB 3.0 USB 2.0 (O) WIFI 1 WIFI 2 S/N 1/2 3 4 5 5 6 7 8 9 10 11/12 Port Name HDMI1/2 TOUCH HDMI OUT TYPE-C MIC in USB2.0(A) USB3.0 USB3.0 USB2.0(O) TV WIFI Function HDMI input port (HDMI wire 5m recommended)

USB interface for HDMI1/2 touch connection HDMI output port(HDMI wire 5m recommended)

TYPE-C interface USB+VIDEO+Audio+charge

(20V/3.25A)(Public USB3.0) MIC input port USB interface on Android system USB interface on TV/Android/OPS system USB interface on TV/Android/OPS system USB interface on Android system TV wireless network interface 1) Annotation: open whiteboard annotation. 2) Page up: go to previous page. 3) Page down key: go to next page. 4) Whiteboard:

open white board software. 5) Back: exit current interface and return to the previous menu. DP TOUCH DP 6) Home: switch between Android home page and OPS channel. 7) Overview: show all the opened applications. 8) Source: select input signals. 9) M enu: open the control panel

. 10) Setting: open the android setting. 11) More: adjust more functions on the sidebar.

~10

~13

LCD Touch AIO LCD Touch AIO XI. Use of Android System 1Switch from Computer System to Android System 1Click Homepage key on remote control to switch to homepage between Android home page and OPS channel, as shown in figure below:

b Homepage of Android System utton on keyboard to switch to homepage bewteen Android home Floating menu is as shown in figure below.Touch the 2) Or press page and OPS channel. 3) to open the homepage bewteen Android home page and OPS channel. 2Switch from Homepage bewteen Android home page and OPS channel 1)ClickHomepagebutton of remote control at homepage bewteen Android home page and OPS channel,or touchOPSon homepage using pen or hands to realize the switch. 2)Click OPS channel. Android System 3 utton on front panel at homepage bewteen Android home page and ey in floating menu b k Setting X. Introduction to Remote Controller

(Product images are for illustrative purposes only and may differ from the actual product) 3 4 1 2 6 7 8 10 12 14 15 18 19 22 23 25 26 1 1 8 8 10 10 27 27 28 28 15 15 P.M ODE S.MODE DIS.MODE MUTE

ABC DEF 5 GHI JKL MNO PQRS TUV WXYZ EPG SOURCE MENU OK DISPLAY EXI T VOL PgUp CH PgDn F1 F5 F9 F2 F6 F3 F7 F4 F8 F10 F11 F12 Alt T+ ab Space Alt F4+

Right VGA HDMI TV Mult imedia ZOOM ECO PRS RN LOCK Y53 80 v+

v+

v-

v-

PG+

PG+

PG-

PG-

9 11 13 16 29 17 20 21 24 27 28 5 5 9 9 11 11 13 13 7 7 30 30 16 16

~12

~11~

1 2 D of UP mode own, eft, L UDLR ( Up, D HDMI 1,HDMI 2, startup or standby. 1.Power (standby key): press this key to enter the 2.Picture mode: press picture mode key to have circular switch between picture modes of Stan-

dard, soft, user and bright. 3.Sound mode: press this key to circular switch of sounds between standard, music, movie, sport and user. 4.Display mode: press this key to have circular switch of picture scale between: auto,

, 4:3 , 16:9 zoom , zoom , full screen, nonlinear and point-

to-point. 5.Mute: press mute key to enter mute mode.The mute mark is shown at upper left corner of screen. Press this key again to release mute state and the mark on screen will disappear. 6.Figure: it is valid under signal source only TV and used for receiving TV channel, or inputting figure in corresponding menus. 7.Homepage:press this key to switch from WIN-

DOWS to homepage of Android. 8.Signal source: press this key to pop up list of and own arrow to switch signal source; press the input signal sources, including

, analogue TV built-in component,computer, TV, computer, Android and video. 9.Menu:press this key in all modes to display the overall setting options. 10.Direction key: press Right) key to adjust or select menu options. 11.OK key:press this key to confirm certain option. 12.Display:press this key to display the resolu-

tion of present signal source. 13.Exit: press this key to exit present menu. 14.Windows/Whiteboard function key. 15.Volume:P ress olume(+)/(-)to adjust volume. V ress this key under mute mode to release mute state. P 16.Press this key to switch channel,or page up/down. 17.Color key: to have prompt function in menu of digital 18.Press this key to enter the play the previous song. 19.Press this key to enter the next directory or play the next song. 20.Press this key to fast forward. 21.Press this key to rewind. 22.Press this key to play or pause program. 23.Press this key to stop play. 24. Channel shortcut key: to switch to corres-

ponding channel by one key. 25.Picture zoom: press this key to zoom in or zoom out picture. 26.ECO:press this key to turn off screen brightness. 27.LOCK:press this key to lock screen, remote controller and functions of key. 28.PRSRN: Press this button to capture the screen and save. 29.F11/F22/Alt+Tab/Space/Alt+f4/Right, Press these keys to have corresponding functions under the signal source of 30.Freeze:Press this button to freeze the picture of current playing screen and continue to play audio. previous directory

.TV OPS or

Page 1 of 1 FCC ID: 2A8HI-GC561622 Label and Location All-In-One Touch Screen Model No.: HS-65IW-L06PA FCC ID : 2A8HI-GC561622 Size: L: 4.5cm*W: 4.0cm Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Product Specification P/N366W0026 REV.X1 Data2019/05/27 ProtocolTom Shen Zhen I-IOE Communication Technology Co., Ltd. Antenna Specification Item Specification Comment Impedance 50 Test Condition Passive Test Freq. Range 2400-2500MHz 5150-5850MHz Antenna Type Rod Antenna Peak Gain VSWR 3.3dBi 2400-2500MHz2.0 5150-5850MHz2.0 Polarization Type Vertical Radiation Type Omnidirectional Connector Type RP-SMA-J RF Cable Type N/A Dimension OD13*195mm Operating Temp

-40+85 Storage Temp

-40+85 Shen Zhen I-IOE Communication Technology Co., Ltd. 1.Efficiency/ Gain Test Freq MHz 2400MHz 2410MHz 2420MHz 2430MHz 2440MHz 2450MHz 2460MHz 2470MHz 2480MHz 2490MHz 2500MHz Efficiency / Gain Test Effi

Gain dBi 52%

52%

54%

54%

54%

55%

54%

54%

54%

54%

52%

1.73 1.73 1.94 2.07 1.95 1.97 2.05 2.27 2.49 2.58 2.52 Shen Zhen I-IOE Communication Technology Co., Ltd. FreqMHz Efficiency / Gain Test Effi%

GaindBi 5150MHz 5170MHz 5190MHz 5210MHz 5230MHz 5250MHz 5270MHz 5290MHz 5310MHz 5330MHz 5350MHz 5370MHz 5390MHz 5410MHz 5430MHz 5450MHz 5470MHz 5490MHz 5510MHz 5530MHz 5550MHz 5570MHz 5590MHz 5610MHz 5630MHz 5650MHz 5670MHz 5690MHz 5710MHz 5730MHz 5750MHz 5770MHz 5790MHz 5810MHz 5830MHz 5850MHz 34%

35%

37%

37%

37%

37%

35%

37%

38%

37%

37%

39%

40%

41%

38%

34%

33%

31%

31%

34%

37%

38%

40%

40%

42%

41%

39%

41%

44%

46%

46%

46%

44%

45%

47%

46%

Shen Zhen I-IOE Communication Technology Co., Ltd. 0.34 0.34 0.58 0.57 0.55 0.72 0.84 1.52 2.21 2.52 2.71 3.19 3.32 3.1 2.28 1.64 1.23 0.65 0.37 0.51 0.59 0.92 1.24 1.19 0.98 0.74 0.57 0.8 1.28 1.7 1.82 2.21 1.97 2.06 2.05 1.65 2. Radiation Pattern/

2450MHz 5350MHz Shen Zhen I-IOE Communication Technology Co., Ltd. 1 2 3 4 5 ECNNUMBER REV. X1 DESCRIPTION FIRSTRELEASE DATE 0527'19

2 A B C 1

3

A B C D E NOTES:

1.THESURFACEOFTHEPRODUCTISNOT DIRTY,SCRATCHED,DEFORMED,DAMAGED,ETC.. 2.100VSWRTEST 3.FREQUENCYRANGE:

4.CRITICALDIMENSION 5.ALLMATERIALSAREINCOMPLIANCEWITHROHSCOMPLIANT E D C B A CONNECTOR BASE2 RIVET BASE1 SHELL 1 1 1 1 1 RP-SMA-J,NICKELPLATEDBRASS ABS,BLACK POM,BLACK ABS,BLACK TPE,BLACK ITEM PARTNAME Q'TY PART MATERIALFINISH

GENERALTOLERANCE

.X 0.30

.XX0.15

.XXX0.15 SCALE:

1:1 mm UNIT:

SIZE:

A4 Tom DRAWN:

CHECK:

APPROVE:

PROJECTNAME:

PARTNO:

TITLE:

REV.X1 SHEET:

11 1 2 3 4 5 A B C 0527'19 DATE:

DATE:

DATE:

366W00026

Shenzhen HCTek Co., Ltd Add: 4-8F, building a and 1F, building B, No.32, Hongyin Road, Loucun community, Xinhu street,Guangming District, Shenzhen, Guangdong China Date: 2022-9-5 FCC ID: 2A8HI-GC561622 Dear Sir/Madam, We, Shenzhen HCTek Co., Ltd Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model:

Product name: All-In-One Touch Screen Model no.: HS-65IW-LO6PA, _DXXXXXXXXXXXXXXXXXXX, HXXXXXXXXXXXKXXXKKKXX, ZXXXXXXXXKXXXXKKXXKKX, CXXXKXXXKKXXXXKKXXXKX (X for 0-9, A-Z,"-" or space) Sincerely, Name/Title : zhihui Li/Quality manager Company: Shenzhen HCTek Co., Ltd Address: 4-8F, building a and 1F, building B, No.32, Hongyin Road, Loucun community, Xinhu street,;Guangming District, Shenzhen, Guangdong China Phone: 0755-33580306 Fax: 0755-23212683 E-Mail: li.zhihui@huake-tek.com

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2022-9-5>

Pursuant to Paragraphs 0.457 and 0.459 of the Commission's Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID Model name 2A8HI-GC561622 HS-65IW-LO6PA For the product stated above, we request that the following information be held confidential;

Long-Term Short-Term Short-Term Exhibits Confidentiality Confidentiality Confidentiality Days External Photos Internal Photos Block Diagram xX Schematics Xx Test Setup Photos Users Manual Parts List Xx Tune Up Operational Descriptions Xl The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title: zhihui Li/Quality manager Company: Shenzhen HCTek Co., Ltd Address: 4-8F, building a and 1F, building B, No.32, Hongyin Road, Loucun community, Xinhu street,Guangming District, Shenzhen, Guangdong China Phone: 0755-33580306 Fax: 0755-23212683 E-Mail: li.zhihui@huake-tek.com

Shenzhen HCTek Co., Ltd 4-8F, building a and 1F, building B, No.32, Hongyin Road, Loucun community, Xinhu street,;Guangming District, Shenzhen, Guangdong China Date: 2022-9-5 FCC ID: 2A8HI-GC561622 Model Number: HS-65IW-L06PA To:

Federal Communications Commission. Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, Shenzhen HCTek Co., Ltd , declare that this EUT (FCC ID: 2A8HI-GC561622) doesnt have Ad Hoc mode function on non-US/Canada frequencies. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, AG Wb Name/Title: zhihui Li/Quality manager Company: Shenzhen HCTek Co., Ltd Address: 4-8F, building a and 1F, building B, No.32, Hongyin Road, Loucun community, Xinhu _ street,Guangming District, | Shenzhen, Guangdong China Phone: 0755-33580306 Fax: 0755-23212683, E-Mail: li.zhihui@huake-tek.com

Shenzhen HCTek Co., Ltd 4-8F, building a and IF, building B, No.32, Hongyin Road, Loucun community, Xinhu street,Guangming District, Shenzhen, Guangdong China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2022-9-5 To whom it may concern:

We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2A8HI-GC561622 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title: zhihui Li/Quality manager Company: Shenzhen HCTek Co., Ltd Address: 4-8F, building a and 1F, building B, No.32, Hongyin Road, Loucun community, Xinhu street,;Guangming District, Shenzhen, Guangdong China Phone: 0755-33580306 Fax: 0755-23212683 E-Mail: li.zhihui@huake-tek.com

Shenzhen HCTek Co., Ltd 4-8F, building a and 1F, building B, No.32, Hongyin Road, Loucun community, Xinhu street,Guangming District, Shenzhen, Guangdong China UNII Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID: 2A8HI-GC561622

(1) DFS Device: Master Client with Radar detection capability N/A &X Client without radar detection capability,

(2) Active / Passive Scanning , adhoc mode access point capability Active Scanning passive scanning Frequency (the device can (where the device Ad Hoc Mode Access point Band (MHz) transmit a probe is can listen only capability capability

(beacon)) with no probes) 5180-5240 Yes | KINo | Xl Yes No Yes | KJ No Yes | KINo 5190-5230 Yes | KINo | Yes No Yes | KJ No Yes | KINo 5210-5210 Yes | KINo | Yes No Yes | KJ No Yes | KxINo 5260-5320 Yes | KINo | Yes No Yes | KJ No Yes | KJNo 5270-5310 Yes | KINo | Yes No Yes | KJ No Yes | KINo 5290-5290 Yes | KINo | Yes No Yes | KJ No Yes | [No 5500-5700 Yes | KINo | Yes No Yes | KJ No Yes | KJNo 5510-5690 Yes | KINo | Yes No Yes | KJ No Yes | KINo 5530-5610 Yes | KINo | &lYes No Yes | KJ No Yes | KNo 5745-5825 Yes | XINo | Yes No Yes | KJ No Yes | KINo 5755-5795 Yes | XINo kl] Yes No Yes [| KINo Yes | XINo 5775-5775 Yes | XINo kK] Yes No Yes [| XINo Yes | XINo

(3) Country code selection ability Yes EI No If yes, pls explain how it was implemented:

(4) Meet 15.202 requirement Kl Yes No

(5) pls check below :

|A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices BAJA client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply KK] Does not apply

(If apply, pls help to provide explanation on it was implement, and how software was controlled) Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Liha

(Signed) Name/Title:

Company:

Address:

Phone:

Fax:

E-Mail:

zhihui Li/Quality manager Shenzhen HCTek Co., Ltd 4-8F, building a and 1F, building B, No.32, Hongyin Road, Loucun community, Xinhu street,Guangming District, Shenzhen, Guangdong China 0755-33580306 0755-23212683 li.zhihui@huake-tek.com