FCC ID: 2A4ZB-S8 Multi-function wireless charger stand

Multi-function wireless charger stand User Manual Made In China 1. iwatch charging area 2. Charging area for vertical mobile phone 3. Charging area for horizontal mobile phone 4. Mobile phone holder 5. Mobile phone charging indicator 6. Iwatch charging indicator 7. Airpods charging area 8. Airpods charging indicator 9. Heat-dissipating area 10. USB input port Specifications Input Output Material 9V-2A12V-2A 15W for mobile phone area, 2.5W for iwatch area, 5W for airpods area ABS How to use:

Connect the USB cable and the indicator light will flash once and then go off after the device starts. At this time, the self-test of the device is completed. Press the Watch Pop-up button, and put on the corresponding device for charging. Special note:

It is necessary to install the rising silicone for mobile phones when charging the iphone 12/13MINI (all mobile phones of the remaining sizes are not required to be installed. The mode of installation is as shown in the figure below) Warning Please keep this product out of the reach of children. Please keep this product away from heat dissipating appliances such as radiators, or flammable and explosive items. Do not use this product with wet hands or in wet areas. Do not disassemble this product by yourself. In case of technical assistance, please contact the supplier or hire a qualified repairer. Troubleshooting 1. When to reset In case the product is not used for a long time, the product will automatically enter into a sleep state, and in case it cannot be charged due to a sudden power failure, it can be restored after reconnecting the power supply. 2. No charging If the indicator light flashes rapidly while this product is charging, it proves that a metal is detected by the charging coil (foreign object detection is activated). Please remove relevant metals and then charge again. If the failure is not removed, please unplug the power and restart this product for normal use. 3.Slow charging 1)Please use the adapter that supplied with this product, or other original adapters above QC3.0. 2)Check if the corresponding device is aligned with the charging coil. FCC Warning Statement: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located for operating in conjunction with any other antenna or transmitter.

Label and label location High:2cm Multi-function wireless charger stand FCC ID:2A4ZB-S8 Wide:3cm

< Shenzhen Heshan Technology Co., Ltd >

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID:2A4ZB-S8 To Whom It May Concern, C5266091_X10_Ed.1 Date: 2022-09-08 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality No No No No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Zhang jiangchuan Title: N/A 1/1

Shenzhen Heshan Technology Co., Ltd Model Difference Product description: Multi-function wireless charger stand Model name: S8 S8-A,S8-B,S8-C,S9,S10 Trade Name: N/A FCC ID:2A4ZB-S8 All the model are the same circuit and RF module, only for model name and colour are different. Regards Sincerely Clients signature:

Clients name / title : Zhang jiangchuan (N/A) Contact information / address: Third floor, No. 8, Zone D, Tangtou third industrial zone, Tangtou community, Shiyan street, Bao'an District, Shenzhen

C5266091_X8_Ed.1 Letter of Authorization

<Shenzhen Heshan Technology Co., Ltd >

Company:Shenzhen Heshan Technology Co., Ltd Address:Third floor, No. 8, Zone D, Tangtou third industrial zone, Tangtou community, Shiyan street, Bao'an District, Shenzhen Product Name: Multi-function wireless charger stand Model Number: S8 S8-A,S8-B,S8-C,S9,S10 FCC Identifier:2A4ZB-S8 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. is allowed to forward all Name: Zhang jiangchuan Date: 2022-09-08 Title: N/A Signature of applicant:

1/1