FCC ID: 2AN75-ZINO2RX HUBSAN ZINO 2

Zino 2 U s e r M a n u a l V2.0 DISCLAIMER & WARNING All users must read product operating instructions as well as this liability disclaimer before using any Hubsan product. By using a Hubsan product(s), users are accepting the terms and conditions of Hubsan liability and operational guidelines. This product is not suitable for minors under 14 years of age. While operating a Hubsan product

(s), users also accept all liability and responsibility for their own behavior, actions as well as any consequences resulting thereof while using a Hubsan product(s). These products may only be used for purposes that are proper and in accordance with local regulations, terms and any applicable policies / guidelines Hubsan may make avail-

able. Users agree to comply with these terms and conditions, along with any and all relevant policies / guidelines set forth by Hubsan. INSTRUCTIONS Some product flight functions are restricted in certain areas. Once you use this prod-

uct, you are deemed to have read carefully the relevant ICAO regulations, local airspace control provisions and the regulations governing UAVs. You assume all liability for any non-compliance with the foregoing, are responsible for the conse-

quences for your actions as well as any indirect and / or direct liability that arises as a result of these limitations. FLIGHT ENVIRONMENT REQUIREMENTS

(1) Select an open environment devoid of high rise buildings and tall obstructions

(such as trees and poles). Near buildings and obstacles, flight control signals and GPS signals can be severely weakened; GPS functions such as GPS mode and Return to Home may not function properly.

(2) Do not fly in bad weather conditions (such as in wind, rain or fog).

(3) Fly the aircraft in ambient temperatures of 0-40 .

(4) When flying, please stay away from obstructions, crowds, high voltage lines, trees, water, etc.

(5) To avoid remote control signal interference, do not fly in complex electromagnet-

ic environments (such as venues with radio stations, power plants and towers).

(6) The aircraft cannot be used in or near the Arctic circle or Antarctica.

(7) Do not fly in no-fly zones.

(8) Do not operate the aircraft near high pressure lines, airports or areas with severe magnetic interference. IMPORTANT SAFETY INFORMATION OPERATION Be extremely careful and responsible when using the aircraft. Small electronic components can be damaged due to crashes or exposure to moisture / liquid. To avoid any injuries, do not use the aircraft with broken or damaged components. MAINTENANCE Do not try to open or repair the units by yourself. Please contact Hubsan or Hubsan authorized dealers for service. For more information, please visit the official website at www.hubsan.com. BATTERY Do not disassemble, squeeze, impact, burn, drop or trample the battery. Do not short-circuit or put the battery terminal in contact with metal. Do not expose the battery to temperatures above 60 C. Charge the aircraft battery prior to flight. Use a Hubsan dedicated charger for charging. Keep the battery out of the reach of children and away from any kind of moisture. FLIGHT Please be mindful of personal safety and the safety of others while flying.

-Do not fly in bad weather conditions.

-Do not attempt to catch the aircraft while it is in flight.

-This product is intended for experienced pilots over the age of 14.

-After every flight, completely disarm the aircraft motors and disconnect the aircraft from power. Then, you may power off the remote control. READ THE DISCLAIMER AND SAFETY GUIDELINES FIRST BEFORE USE. Symbol Explanation:

Prohibited Operation Important Notice Instruction Explanation / Reference HUBSAN AIRCRAFT USES SMART BATTERY If you do not plan to fly the aircraft for a long time, store the battery ~50%

charged to maintain battery performance and life. Please use Hubsan chargers for battery charging. Discharge the battery at 5C current or below. To avoid discharge related battery damage, do not prolong the discharge time. Do not charge on carpet to avoid fire. Batteries need to be recharged if unused for over 3 months. 1. Do not disassemble or reassemble the battery. 2. Do not short-circuit the battery. 3. Do not use or charge near sources of heat. 4. Do not put the battery in contact with water or any kind of liquid. 5. Do not charge batteries under sunlight or near fire. 6. Do not puncture or subject the battery to force of any kind. 7. Do not throw or manhandle the battery. 8. Never charge a battery that has been damaged, become deformed or swelled. 9. Do not solder on or near the battery. 10. Do not reverse charge or over discharge the battery. 11. Do not reverse charge or reverse the battery polarities. 12. Do not connect the battery to a car charger / cigarette lighter or any kind of unconventional power source. 13. This battery is prohibited for non-designated devices. 14. Do not mix other types of batteries with lithium batteries. 15. Do not exceed the specified charging time. 16. Do not place the battery in a microwave or in areas of high pressure. 17. Do not expose the battery to the sun. 18. Do not use in environments with high static electricity (64V and above). 19. Do not use or charge in temperatures below 0 and above 45 . 20. If a newly purchased battery is used, leaking, possesses a bad smell or other abnormalities, return immediately to the vendor. 21. Keep away from the reach of children. 22. Use a dedicated battery charger and follow all charging requirements. 23. Minors who use the battery and its dedicated unit must be supervised by an adult at all times. Contents Disclaimer Important safety information Battery use precautions 1 Aircraft 1.1 Aircraft Spare Part 1.2 Aircraft Battery 1.2.1 Aircraft Battery Charging 1.2.2 Aircraft Battery Installation 1.2.3 Intelligent Flight Battery Function 1.2.4 Precautions For Low Tempera-

ture 1.2.5 Precautions For Battery 1.3 Propellers 2 Remote ControllerAmerica Mode 2 2.1 Names Of Remote Controller Compo-

nents 2.2 Remote Controller Features 2.3 Charging The Transmitter Battery 2.4 Remote Control Diagram 2.5 Remote Control Antenna Angle 3 Flight 3.1 Download The X-hubsan 2.0 App 3.2 Main Interface Guide 3.3 Pairing The Aircraft 3.4 Aircraft Calibration 3.4.1 Horizontal Calibration 3.4.2 Compass Calibration 3.4.3 Gps Accuracy Test 1 1 3 3 3 4 5 5 6 6 6 7 8 9 10 10 10 11 11 13 13 13 14 15 16 16 16 17 18 18 18 19 19 20 20 21 3.5 Staring/stopping The Motors 4 Flight Controller 4.1 Flight Control Mode 4.2 Flight Orientation Indicator

( Single-color Lamp) 4.3 Eturn-to-home(Rth) 4.4 Search The Drone Apron 4.5 Flight Mode 4.5.1 Headless Mode 4.5.2 Creative Video 4.5.3 Follow Mode 4.5.4 Orbiting 4.5.5 Waypoint 4.5.6 Line Fly Mode 4.5.7 Time-lapse Photography 22 4.5.8 Panorama Mode 23 4.6 Gimbal Camera 24 4.6.1 Camera Settings 24 4.6.2 Gimbal Pitch Axis Adjust-

ment 24 25 4.6.3 Tf Card 25 5 Faq Zino 2 Parts & Accessories Limitation Of Liability Fcc Information 32 33 27 1.Aircraft 1.1 Aircraft Spare Part 1 2 3 9 11 5 6 4 7 10 8 1 2 7 8 Propeller A Propeller B 3 4 Motor Tripod (With Antenna) 5 6 Body shell 4K HD Camera 3-axis gimbal Gimbal Protection Guard 9 Bind key 11 10 TF Slot USB Slot 1 14 15 13 16 12 12 13 Intelligent Battery Battery level indicator 14 15 16 Battery power switch Battery buckle Auxiliary altitude hold system Rear LOGO 2 1.2 Aircraft Battery 1.2.1 Aircraft Battery Charging Aircraft Lithiun Battery Capacity: 3800mAh, 15.2V lithium battery equipped with a standard charger,charging time is about 110 minutes. Connect the power adapter to AC power (100V-240V, 50-60Hz). Connect the Intelligent Flight Battery and the power adapter with Intelligent Flight Battery turned off Intelligent Flight Battery Level indicator will flash and indicate current battery lever under charging Intelligent Flight Battery is fully charged when power indicator lights are all off. Please remove the Intelligent Flight Battery and power adapter to complete charging. Note: After using the battery, please re-charge it in time (at least 50%) to avoid long-term storage of the battery and affecting battery life. Balance Charger Charger Adapter Aircraft Battery 1.2.2 Aircraft Battery Installation 1 2 3 Prepare the aircraft battery Put the battery in the battery compartment 2 Check if the battery is fastened 1 3 3 1.2.3 Intelligent Flight Battery Function

(1) Power display: The battery has a power indicator, which can display the current battery power.

(2) Battery storage self-discharge protection: After the battery is fully charged and stored for 10 days without any operation, the battery will automatically turn on the self-discharge mode to protect the battery (there may be slight heating during discharge).

(3) Balance protection: automatically balance the battery cell voltage to protect the battery.

(4) Charging temperature protection: When the battery temperature is below 5 Cor above 40 C, battery will be damaged. So battery will not start charging at this temperature,

(5) Charging over-current protection: High-current charging will seriously damage battery. When charging current is too large, the battery will stop charging.

(6) Overcharge protection: Overcharging will seriously damage the battery. When the battery is fully charged, it will automatically stop charging.

(7) Over-discharge protection: Excessive discharge will seriously damage the battery. When the battery is not in use. Battery will cut off the output when it is discharged to a certain voltage. While over-discharge protection won't start during the flight.

(8) Short circuit protection: When the battery detects a short circuit, it will cut off the output to protect the battery.

(9) Cell damage detection: When the battery detects that the battery is damaged or the battery is seriously unbalanced, it will indicate that the battery is damaged.

(10) Hibernation protection: When the battery is on, the battery will turn off the output after 20 minutes and will enter into no-working state to maintain the power if no electrical equipment is connected. When the battery power is less than 5%, if the machine is locked but not turned off, it will automatically shut down. If the machine is turned off, the battery will automatically enter the sleep state to prevent over-discharge. At this time, short press the battery switch, the power indicator will not light up, the battery can be waken up by charging again.

(11) Communication: The aircraft can obtain battery information in real time through the communication interface on the battery such as voltage and power. Battery switch Short press to check the battery level, it will turn off after 3 seconds S h o r t p r e s s f i r s t a n d t h e n l o n g p r e s s t o t u r n on / off, the indicator light turns on / off 4 1.2.4 Precautions for Low Temperature

(1) If the battery is used in a low temperature environment (-10 C to 5 C), please fully charge and keep the battery warm before use.

(2) The battery cannot be used in an environment below -10 C.

(3) In a low temperature environment, it is recommended to stop the flight immediate-

ly when the APP prompts Low Battery Alarm.

(4) In a low temperature environment, it is recommended that the battery be preheat-

ed to 5 C or higher before flight.

(5) In low temperature environments, the aircraft's wind resistance will be reduced due to the battery output power limitation. Please operate with caution.

(6) Before flying in a low temperature environment, you can insert the battery into the aircraft to warm up for 1 to 2 minutes, and take off after the battery is fully warmed up. 1.2.5 Precautions For Battery Be sure to fully charge each time before using the Intelligent Flight Battery.The Intelli-

gent Flight Battery must be use a Hubsan dedicated power adapter for charging.

(1) The temperature of the Intelligent Flight Battery is high after the flight is over. The Intelligent Flight Battery must be cooled to room temperature before charging the battery.

(2) The charging temperature range of the intelligent flight battery is 5 C to 40 C. If the temperature of the battery cell is not in this range, the battery management system will prohibit charging. The optimal charging temperature range is 25 3 C. Charging in this temperature range can extend the battery life. 5 1.3 Propellers Before installing the propeller, please carefully check the letters beside the aircraft motor and the letters on the propeller. The two letters must be the same when installing; When the blade is damaged or needs to be replaced, remove the screw counterclockwise to remove the propeller. A B A A B B 2. Remote ControllerAmerica Mode 2 2.1 Names Of Remote Controller Components 1) Mobile Device holder 2-1)Throttle / Rudder Stick 2-2) Forward / backward / left /

right flight control levers 3) Return to Home 4) Power 5) F / N / S mode:

Movie mode / normal mode /

sport mode 6) Display 7) Photo 8) Video 9) Gimbal Adjustment Wheel 10) Custom keys 11) Antenna 12) Remote control extension cable 13) Charging / Adapter Port 14 Lanyard hole 15) Rocker storage 16) Cable storage 15 16 15 6 3 4 5 2-1 1 9 7 13 14 2-2 12 10 8 11 6 2.2 Remote Controller Features S/N Key / Switch Function

(1) Throttle / Rudder Stick Push the stick forward or backward and the quad-

copter will ascend or descend (respectively). Push the stick left or right and the quadcopter will fly left or right (respectively).

(2) Elevator / Aileron Stick Push the stick forward or backward and the quad copter will fly forwards or backwards (respectively). Push the stick left or right and the quadcopter will rotate counterclockwise or clockwise (respectively). 1 Throttle / Aileron Stick Push the stick forward or backward and the quad-

copter will ascend or descend (respectively). Push the stick left or right and the quadcopter will rotate counterclockwise or clockwise (respectively). 2 Elevator / Rudder Stick Push the stick forward or backward and the quad-

copter will fly forwards or backwards (respectively). Push the stick left or right and the quadcopter will fly left or right (respectively). 3 Return to Home 4 Power Switch 5 F / N / S mode

(Movie / Normal /

Sport mode) 6 Display 7 Photo 8 Video Long press to enter home mode, short press to exit and return to home;

During the flight, the remote control "Beep... Beep..."

prompt (once every three seconds) Long press to power on or off. Movie mode: Flying speed of the aircraft 1m / s Normal mode: the aircraft flies at the maximum speed set by the APP,12m / s Sport mode: the maximum flying speed of the aircraft is 20m / s Display flight parameters Short press to take photos. Long press to start recording, short press to end recording Gimbal Adjustment Wheel 9 Controls the angle of the gimbal. 7 S/N Key / Switch Function 10 Custom keys Press and hold the Fn button, turn the gimbal adjustment Wheel to adjust tthe brightness of the remote control display at the same time. The remote control buzzer beeps when a low battery is triggered or RTH Press the Fn button for 1.5 seconds, and the beep will stop. Long press the Fn button again 1.5 seconds to restore the beep. Custom keys,set the function on the APP and save it in when the APP is not connected, [short press] Fn doesn't work. Function one: Exit the current flight mode. APP is perform-

ing various functions. In the mode, short press Fn to exit the current mode and the aircraft hover. Function two: short press Fn to execute gimbal return. Function three: no function Settings) 11 Charging /

Adapter Port Charge the remote control or connect with a mobile device 12 Low Battery Warning Low battery warning for the aircraft or remote control:

Remote control "Beep...Beep..." prompt (one time per second) 13 Standby Protection The remote control has no operation for 10 minutes after stand-

by, the remote control "Beep...Beep..." Tips (once every three seconds) After 3 minutes of prompting the sound, the remote control will automatically shut down, and there will be operation within 3 minutes, and the prompt tone will stop 2.3 Charging The Transmitter Battery The remote is charged using the Micro USB cable as shown:

The remote control charging time is about 2.5 hours.The remote control battery indicator light flashes during charging.When charging is complete, the LEDs will be solid. 8 2.4 Remote Control Diagram 4 3 1 5 6 2 7 8 9 9 10 11 12 13 1 Aircraft Battery 2 Remote Controller Battery 3 Propellers Status 4 Aircraft Mode 5 Aircraft GPS Satellite 6 Aircraft Signals 7 Heading Angle 8 Character Area 9 Photo / Video 10 Flight Distance 12 Aircraft speed 11 Compass Calibration /

Headless Mode 13 Photo / Video 9 2.5 Remote Control Antenna Angle

(1) Adjust the angle of the remote control antenna and try to face the flight direc-

tion of the aircraft as much as possible;

(2) Long-distance state, the distance between the two antennas is properly tight-

ened to maintain the antenna directivity;

(3) Closer Sate, the two antennas are properly separated to maintain a wide receiv-

ing range;

(4) Do Not Form an occlusion or cross bettern the antennas. 3 Flight 3.1 Download The X-hubsan 2.0 App Before flying, users must download the X-Hubsan 2.0 APP. Download the APP for free by scanning the code as shown or by download it via APP Store (IOS) Or Goggle Play. X-Hubsan 2.0 10 3.2 Main Interface Guide Home Page Flight Status Motor Status FPV

(Video) Signal Remote Control Signal Aircraft GPS Signal Aircraft Battery Level Setting Not Connected 1 0 0 %

1 1 V Flight Mode Headless On / Off Auto Takeoff / Auto RTH Gimbal Pitch Location Aircraft GPS 00.000000 , -000.0000 45.877503 , -106.12398465m SPEED 0.0M/S H: 0.0m D: 0.0m Camera Setting Photo /

Video Switch Take Photo /

Video Gallery Altitude Ball Transmitter GPS Altitude Distance Note: This is the interface in Map mode 3.3 Pairing The Aircraft

(1) Run X-Hubsan 2.0 APP, choose the aircraft model.

(2) Short press the aircraft power button and then long press for a few seconds to turn it on.

(3) Short press the transmitter power button and then long press for a few seconds to turn it on, connect the transmitter to your mobile device with the RC cable. Not connected Not connected Before Pairing After Pairing N00.0000000,E000.0000000 45.877503 , - 106.12398465m Speed 0.0m/s H: 0.0m D: 0.0m Pitch 0 Roll 0 Yaw 0 11 N00.0000000,E000.0000000 45.877503 , - 106.12398465m Speed 0.0m/s H: 0.0m D: 0.0m Pitch 0 Roll 0 Yaw 0

(4) Start binding (This step is only required when first binding or replace the trans-

mitter, do it manually.) 1. Go to APP - Setting - Controller, transmitter connection method: Leas Transmitter model HT018A Leas Set transmitter and aircraf t connection Joystick setting Custom button Fn No function 2. Using a pin to long press the aircraft bind button to enter binding mode. 3. Select "Set transmitter and aircraft connection" and scan aircraft. 4. Select the aircraft and connect. Tips:

1 . U s i n g a p i n t o l o n g p r e s s t h e a i r c r a f t bind button to enter binding mode;

2 . C l i c k " R e f r e s h " t o r e f r e s h t h e a i r c r a f t l i s t , p l e a s e m a k e s u r e t h e y o u r m o b i l e device and transmitter is connected before refreshing;

3. Select the aircraft and connect. You have to complete the binding process on APP when first use or replace the transmitter, and then you can fly the aircraft with the transmitter directly without connecting to the APP. Tips:

-The binding process has been completed in the factory. Generally, user only need to do the first 3 steps.

-After entering binding mode, all 4 LEDs flash rapidly and become solid after bind-

ing successfully.

-Please keep the distance between the aircraft and transmitter within 1 meter when binding. 12 ControllerScan aircraftHUBSAN_ZINO2_XXXXXXConnectRefreshController 3.4 Aircraft Calibration 3.4.1 Horizontal Calibration During the flight, when the aircraft has a significant horizontal deviation, please land the drone, lock the motor, and place it on the horizontal ground. Then enter the APP setting interface, select horizontal calibration, the aircraft will automatically perform the calibration, the four heading lights will flash, and it will stay on after the calibration is completed. Do not move the aircraft during calibration. Aircraft Aircraft model Parameter unit Metric Unit (m/s) Waypoint parameters Device binding Start binding The aircraft is bound to the current mobile device, and on longer establish a binding with other devices. Calibration Compass calibration Horizontal Calibration 3.4.2 Compass Calibration When using for the first time, the compass calibration will pop out before takeoff. Follow the instructions on your screen, rotate the aircraft horizontally the n point the aircraft nose down and rotate it c lockwise. The compass calibration message will disappear once it is complet ed. You must complete the compass calibration before flying the aircraft for the first time. The compass is susceptible to interference by electronic equipments,magnetic interference and metals and interference could lead to erratic behavior and loss of control. Regular calibration helps to keep the compass and its readings accurate. In the "Settings", select "Compass Calibration" under "Calibration". 13 3.4.3 GPS Accuracy Test After entering the APP interface, tap on "Aircraft", select "GPS Accuracy Test" then tap on "En able / Restart GPS Accuracy Test". The aircraft will automatically proceed to test. Aircraft GPS Accuracy Test Current GPS Accuracy 5m GPS Accuracy Test Timeout 15 Start GPS Accuracy Test Return altitude setting The aircraft will rise to the set RTH altitude before activate RTH 3.5 Staring/Stopping the Motors Motor starting condition

(1) The aircraft, remote control and mobile phone have been connected;

(2) The aircraft has been calibrated by the compass (four Orientation lights are always on);

14

(3) The aircraft must be placed horizontally

(4) It is not recommended to take off forcefully when the GPS satellite signal is not reached. Connected SPEED 0.0M/ S 45.87 7503 , - 106.1 23984 Staring the Motors Push both stick to the bottom outer corners to start the motors. Once the motors have started spinning,Release both sticks simultaneously. Stopping the Motors When the motor is running,Push both stick to the bot tom outer corners to stop the motors. Release both sticks once motors stop. Forced to Stop When flying in the air, the motor c an be forced to stop in 2 seconds with outer eight bar. Use this function with caution, as it can cause the aircraft to fall and may endanger personal safety. 4 Flight Controller 4.1 Flight Control Mode Flight Speed Movie Mode Regular Mode Maximum speed 1m/s Maximum speed is 12m / s, which can be adjusted in the APP settings by 10% -100%

Sport Mode The maximum speed is 20m / s, the sport mode is only available in the GPS mode. 15 45.877503 , -106.12398465mPitch 35Yaw 25Roll 45H: 0.0mD: 0.0m050 Flight Control Mode GPS Mode

(The flight controller judges the GPS signal and switches the corresponding mode) With good GPS conditions, using GPS fixed point and optical flow assist. When the aircraft is hovering, and the GPS quantity is insufficient, using the optical flow fixed-point mode. The effectively fixed height of optical flow mode is 5 meters and greater than 5 meters for attitude mode. In this mode, the maximum speed of the aircraft is 3m / s. The intel-

ligent mode is not available. Please fly with caution. Optical flow mode Attitude mode When GPS and optical flow effects are weak, the only manual flight is available, and intelligent mode is prohibited. In attitude mode, the aircraft's fixed point is abnormal. Please land as soon as possible. 4.2 Flight Orientation Indicator ( Single-Color Lamp) Power On And Start Up Compass Calibration Horizontal Calibration Calibration All 4 LEDs flash slowly Calibrate Compass 1:All 4 LEDs flash in cycle Calibrate Compass 2:All 4 LEDs flash in vertical pairs alter-

nately All 4 LEDs flash slowly Flight Mode Regular Mode All 4 LEDs are solidly lit Low Power Indicator Loss Of Flight Control Indicator Fore / frontal blue LEDs stay solidly lit and the rear red LEDs flash rapidly The front Orientation light flashes slowly in blue, and the rear Orientation light is steady red. (When there is a conflict with low battery, priority is displayed.) Headless Mode RTH Photo Video Fore/front blue LEDS flash in vertical pairs alternately and rear red LEDs stay solidly Fore / frontal blue LEDs stay solidly lit and the rear red LEDs flash slowly Rear red LEDs flash once Rear red LEDs flash alternately Light-Off Long press the camera button. 16 4.3 Return-to-home(Rth) There are three types of RTH: One-key RTH, Low Battery RTH,and Failsafe RTH. When taking off, GPS 6 stars, the aircraft successfully recorded to the return point. If there is no GPS signal forced take-off, the position with the latest GPS 6 stars is recorded as the return point. RTH-Process 1. Record "Home Point" 2. Trigger return conditions 3. Adjust t he direction of the head 4. Return to the return altitude set by APP

(1) Regardless of the current height of the aircraft, if the aircraft is within 5 meters of the horizontal distance, land directly;

(2) If the horizontal distance is 5 meters away and within 20 meters, return at the current altitude;

(3)In 20 meters away,if the altitude of aircraft is more height than the return altitude ,it will re turn directly; If no, it will rise to up to the return alt itude ,and then RTH ;

5. Search for the drone apron during the landing process (Make sure this func-

tion is on). One-key RTH APP one-Key RTH / remote control one-Key RTH Low Battery RTH The flight controller will display a notice when a low battery warning is triggered. The aircraft will automatic ally re turn to the Home Point if the current power is enough,otherwise it will land directly. when without GPS signal or signal is not strong that will land directly. Performance requirements:

(1) The appropriate low-voltage protection voltage is automatically calculated according to the altitude and distance of the flight;

(2) After the low power forced landing or crash, if the power is lower than 10%, enter the protection mode: turn off the picture transmission, but save normal data communication. Failsafe RTH When t he aircraft loses connection with t he remote control for more than 5 seconds, the aircraft automatically returns or land directly.Performance require-

ments:

(1) After the aircraft loses control for 5 seconds, it triggers automatic return;

(2) If t he connection is restored during the return flight, the return flight can be canceled;

(3) Landing directly when there is no GPS signal or the signal is not strong.

(4) After the aircraft re-establishes the connection, the priority control signal establishes a connection. The connection is not established until 10 seconds after the signal is transmitted, and the image connect ion can also be forced by the shortcut button. 17 4.4 Search The Drone Apron When the aircraft landed or returned to a height of about 10 meters from the ground, it will automatically enter the search for the drone apron func-

tion. Connected 1 0 0 %

1 1 V 45. 877 503 , -106. 1239 84 SPEED 0 .0M/S T: 0% R: 0%

E: 0%

A: 0%

(1) The gimbal overlooks the search for the drone apron [H], Apron requirements: 1 Sharp contrast, 2 white "H" lettering, 3 Apron without obstruction.

( 2 ) T h e a i r c r a f t w i l l f i r s t p a n t o t h e t o p o f t h e a p r o n a n d l o c k s t h e a p r o n , t h e n d e s c e n d s m o o t h l y a f t e r s u c c e s s f u l r e c o g n i t i o n . W h e n l a n d i n g t o a h e i g h t o f l e s s t h a n 3 m e t e r s , t h e a i r c r a f t p a n / t i l t w i l l resume normal view and no longer adjust the posit ion of the aircraft and land directly. If an error is identified or other unexpected circum stances occur, press the stop button to exit the function.

( 3 ) I f t h e a i r c r a f t h a s n o t b e e n f o u n d t o t h e a p r o n o r c r i t i c a l l o w battery when it has landed 5 meters, the aircraft will land directly.

(4) The search for the drone apron function cannot be performed in video mode.

(5) If needn't, please turn it off in the settings. 4.5 Flight Mode 4.5.1 Headless Mode Connected 1 0 0 %

1 1 V 45.877503 , -106.123984 SPEED 0.0M/S T: 0% R: 0%

E: 0%

A: 0%

Record a flight paththe direction of the nose is the direction of advancethe heading and forward direction of the aircraft are independent of the direction of the nose during flight. 18 45.877503 , -106.12398465mH: 0.0mD: 0.0m45.877503 , -106.12398465mH: 0.0mD: 0.0m 4.5.2 Creative Video Panorama Photography:

(1) Select the direction of rotation (clockwise / counterclockwise);

(2) Set the rotation angle, the range of rotation angle (90 -360 ,accuracy 1);

(3) Set the speed (2-30 / sec, accuracy 1);

(4) Click GO, the aircraft rotates in place in the hover position,shooting during the rotation + storage Video recording;

(5) During the execution, you can click the exit button to exit the mode and save the video. Connected Angle Speed ccw cw E: 0% A: 0%

4.5.3 Follow Mode Enter into follow mode to choose the Image tracking and GPS follow. Connected N o r m a l M o d e Waypoint M o d e O r b i t M o d e Follow Mode C r e a t i v e V i d e o 45.877503 , -106.123984 SPEED 0.0M/S T: 0% R: 0%

E: 0%

A: 0%

Image Tracking:Select the target on the APP. After the selecting successfully, tap on

"Go" and the aircraft will follow the movements of the target. The range of tracking altitude and distance is 5-15 meters. This function cannot be turned on within 5 meters of the distance between the person and the aircraftGPS Follow: the aircraft will follow the control device to fly when turning on the GPS follow. 19 100%11V45.877503 , -106.12398465mH: 0.0mD: 0.0m100%11V 4.5.4 Orbiting Tap on "Mode Selec tion" then "Orbit Mode" to set the current location or the position of the mobile device as the center.During Orbit mode, you can adjust the speed and direction by moving the control stick left and right and adjust the orbit radius by moving the control stick forward and backward. Connected N o r m a l M o d e Waypoint M o d e O r b i t M o d e Follow Mode C r e a t i v e V i d e o 45.877503 , -106.123984 SPEED 0.0M/S T: 0% R: 0%

E: 0%

A: 0%

4.5.5 Waypoint The aircraft will fly along the flight path drawn on-screen or saved ,you can adjust the speed of the aircraft during flight . Connected Waypoint Waypoint Planning Waypoint Memory Tap one and enter into the operation interface 45.877503 , -106.123984 SPEED 0.0M/S T: 0% R: 0%

E: 0%

A: 0%

Waypoint Planning: You can preset the waypoint parameters such as the number of waypoin ts, the altitude of each waypoints and other parameters. The aircraft will follow the preset parameters after you activate waypoint mode. You can control the flying speed during flight or you can pause or resume the Waypoint mode. 20 100%11V45.877503 , -106.12398465mH: 0.0mD: 0.0m45.877503 , -106.12398465mH: 0.0mD: 0.0m100%11V Waypoint Memory: After entering the mode, fly the aircraft and tap on "Memorize Waypoints" on the APP and the aircraft will mark the location. After memorizing all the waypoints, upload and execute, then the aircraft will fly according to the memory. If the aircraft is not in the starting position, the aircraft will fly to the starting position before starting this function. 4.5.6 Line Fly Mode Tap on "Mode Selection" then "Line Fly Mode".Set the angle,distance and speed of the aircraft. Performance requirements:

1. Set the angle (0 ~ 360 , accuracy 1 );

Set the distance (10-100 meters, accuracy 1 meter); set the speed (1-8 m / s, accura-

cy 0.1);

2. Once setup is complete, the aircraft will execute Line Fly mode. During the flight, pilots can take photos or videos manually , or pause / resume /

stop the flight at any time. During the flight, the throttle stick is co ntrollable and the other directions are uncontrollable;

3. You can pause/resume/stop the flight at any time. 4. When the aircraft is low on battery or lost connection,the aircraft will always set Return to Home as the priority mission. ConnectedLine Fly Mode T: 0% R: 0%

E: 0%

A: 0%

45.877503 , -106.123984 SPEED 0.0M/S T: 0% R: 0%

E: 0%

A: 0%

21 100%11V45.877503 , -106.12398465mH: 0.0mD: 0.0mPreview RouteAngle0D i s t an c e10mSp e e d1.0m/s1m/s8m/s100m036010m 4.5.7 Time-lapse Photography When you choose time compressor mode, you can choose free time-lapse and surround time-lapse. Hover mode 1 0 0 %

1 1 V free time-lapse surround time-lapse Free Time-lapse The aircraft will take a certain number of photos and compose time-lapse videos automatically according to the parameters which you set. During the process of shooting, the user can control the flight of the aircraft freely.

(1) choose free time-lapse;

(2) set the shutter interval taken by the aircraft, the time of video generated and the maximum flight speed;

(3) after done, please click GO and start shooting. Hover mode 1 0 0 %

1 1 V T h e S h u t t e r I n t e r v a l 2 s The Time Of Video Generated 3 s 1 5 s 3 0 s GO The Maximum Flight Speed 0.5m/s 3.0m/s 22 Surround Time-lapse The aircraft will take a certain number of photos and compose time-lapse video automatically according to the circle point of interest and the parameters which you set. During shooting, oper-

ating lever will automatically quit the task.

(1) select surround time-lapse

(2) set the shutter interval taken by the aircraft, the time of video generated and the maximum flight speed

(3) set the circle direction, and position the circle center by adjust-

ing the circle radius and the direction of the aircraft nose

(4) after done, please click GO and start shooting. Hover mode 1 0 0 %

1 1 V The Time Of Video Generated 3 s 3 0 s T h e M a x i m u m F l i g h t S p e e d 0.5m/s 3.0m/s cw GO The Circle Ra dius 10m 500m ccw 4.5.8 Panorama mode In the panoramic mode, you can choose spherical, 180 , vertical shooting and wide angle shooting.In this mode, the aircraft will perform the shooting task automatically. After the shooting done, you can view photos and videos from the TF card, also export photos and videos and composite it. During shooting, the user will quit the task automatically. Hover mode 1 0 0 %

1 1 V Spherical 180 Vertical Shooting Wide Angle Shooting 23 4.6 Gimbal Camera 4.6.1 Camera Settings Click the setting icon for camera on the main interface of the APP and you can set the resolution, white balance, color and other parameters as follows:

Connected Video Resolution 4K Frame Rate 30FPS white balance Auto Color Normal Video Forma MP4 45.877503 , -106.123984 SPEED 0.0M/S 4.6.2 Gimbal Pitch Axis Adjustment APP Ddjustment Method 1: long press the blank of the video preview interface and the mobile device will vibrate once. When the icon appears at the position which you press, you can adjust gimbal pitch axis by sweeping your finger up and down the screen. Method 2: you can fine tune the angle of gimbal pitch by clicking up-down button on the slider of gimbal pitch axis. Connected 45.877503 , -106.123984 SPEED 0.0M/S Transmitter Adjustment You can adjust the angle of gimbal pitch by fiddling with the control thumb-wheel of gimbal pitch. 24 E: 0%T: 0%R: 0%A: 0%45.877503 , -106.12398465mPitch 35Yaw 25Roll 45H: 0.0mD: 0.0m05045.877503 , -106.12398465mH: 0.0mD: 0.0m100%11V(1)(2)(2) 4.6.3 Tf Card

(1) support TF card, U3 above 16G/32G/64G/128G;

(2) hot plug is supported. It is recommended to plug in the TF card after switch off the power. 5 FAQ 1.The mobile device and remote control cannot be connected

(1) Check whether the status of the APP control signal icon has changed

(2) For USB Settings on android phones, check out "Android phone connection tutorial"

2. Aircraft cannot be searched

(1) Restart the plane, remote control and x-hubsan 2.0 APP

(2) Update the aircraft firmware

(3) Check whether the TF card slot of the drone is keeps on red light, if it flashing, means the aircraft is abnormal 3. Picture transmission stuck or easy to lose control and disconnected

(1) Adjust the antenna Angle to the aircraft, without the block between them

(2) Change the flight site, please do not fly in tall buildings, or near signal tower

(3) Update the latest firmware 4.The aircraft is hovering unsteadily

(1) Change the flight site, please do not fly near tall buildings and signal towers

(2) Do the compass calibration and horizontal calibration of the aircraft

(3)Judge whether the wind is too strong to affect the flight 5. Aircraft GPS accuracy is not precise or cannot pass the GPS accuracy test

(1) in the open area of the outdoor with GPS over 6 satellite

(2) Walk around near the aircraft

(3) Replace the mobile device 6.The battery cannot charge Replug the charger and battery 7. with short flight time Battery overcharge or high temperature environment can easily lead to reduction of battery life, it is recommended to keep the remaining 50% or so, full charge again before use 25 8. The tilt Angle of the gimbal is too large or the gimbal show abnormal

(1) Restart the aircraft to recalibrate the gimbal

(2) Check on the APP to see whether the gimbal status is normal 9. Gimbal initialize failed Before starting the aircraft, take off the protective cover of the gimbal 10.The picture is not clear

(1) Check whether the lens protective film is peeled off

(2) Fly in a well-lit environment

(3) Shooting parameters setting in camera Settings of APP

(4) Video source files are saved in TF card files with suffix AA 11. Lens fogging

(1) humid climate causes lens foggy, change aircraft storage location Place some desiccant in the protective cover of the gimbal when storage 12. Picture or video is lost

(1) Perform completing recording operation after recording video, otherwise it may lead to video damage or loss

(2) Check whether the TF card is broken 13. constant-height flight by flow cannot be used

(1) The current environment light is weak, please fly on outdoor with sufficient light

(2) detect whether the optical flow lens at the bottom of the aircraft is worn or covered by foreign matter 26 ZINO 2 Parts & Accessories ZINO200-01 ZINO200-02 ZINO200-03 ZINO200-04 ZINO200-05 ZINO200-06 ZINO200-07 ZINO200-08 ZINO200-09 ZINO200-10 ZINO200-11 ZINO200-12 ZINO200-13 ZINO200-14 ZINO200-15 ZINO200-16 ZINO200-17 ZINO200-18 ZINO200-19 ZINO200-20 ZINO200-21 ZINO200-22 ZINO200-23 ZINO200-24 ZINO200-25 27 ZINO 2 Parts & Accessories ZINO200-26 ZINO200-27 ZINO200-28 ZINO200-29 ZINO200-30 ZINO200-31 ZINO200-32 ZINO200-33 ZINO200-34 ZINO200-35 ZINO200-36 ZINO200-37 ZINO200-38 ZINO200-40 ZINO200-46 ZINO000-10 ZINO000-11 ZINO000-12 ZINO000-29 ZINO000-30 ZINO000-37 ZINO000-42 ZINO000-48 ZINO000-54 ZINO000-55 28 ZINO 2 Parts & Accessories ZINO200-47 ZINO200-48 ZINO200-49 ZINO200-50 ZINO200-51 29 ZINO 2 Parts & Accessories ITEM NUMBER NAME OF SPARE PARTS ITEM NUMBER NAME OF SPARE PARTS ZINO200-01 Gyroscope Cover ZINO200-02 ZINO200-03 Upper Body Shell lower body shell, Arm wear gasket Back shell ZINO200-08 ZINO200-07 ZINO200-06 ZINO200-04 ZINO200-05 Front lens base and lower lens base gimbal anti-separtion, Left front arm cover, Right front arm cover, left rear arm cover Right rear arm cover, arm wire cover, Side key Left front rubber feet , right front rubber feet Left front lamp cover, right front lamp cover, Left rear rubber feet , right rear rubber feet Left antenna bracket, right antenna bracket, Socket pressure piece, power board pressure block, Battery anti loose pressing block, battery anti loose top block, Optical flow bracket, battery ejection spring Left front white arm 1

(inc.ESC ) Right front white arm 2 Left rear white arm 3

(inc.ESC ) Rear right white arm 4 Hardware shaft Optical flow lens ZINO200-11 ZINO200-12 ZINO200-09 ZINO200-10 ZINO200-13 ZINO200-14 ZINO200-15 ZINO200-16 ZINO200-17 TOF lenses Fan ZINO200-18 ZINO200-19 ZINO200-20 Cooling bracket gimbal steel plate

(with screw) Gyroscope upper shell, gyroscope lower shell ZINO200-21 gimbal supporter ZINO200-22 Cooling air guide cover ZINO200-23 TF card outside lid ZINO200-24 gimbal protection cover ZINO200-25 rubber feet ZINO200-26 Damping ring ZINO200-27 gimbal dampeners ZINO000-29 propeller A (with screw) ZINO000-30 propeller B (with screw ) ZINO000-48 propellers A+B (with screw) ZINO200-28 motor (with screws) ZINO200-29 ESC (blue ligth module) ZINO200-30 ESC (red light module) ZINO200-31 Aircraft antenna ZINO200-32 ZINO200-33 main board Power adapter board ZINO200-34 power adapter plate FPC ZINO200-35 gyroscope FPC ZINO200-36 GPS 30 ZINO 2 Parts & Accessories ITEM NUMBER NAME OF SPARE PARTS ZINO200-37 Screw ZINO000-37 screwdriver ZINO200-38 Battery ZINO200-40 adapter (Europe) ZINO200-46 remote HT018A ZINO000-10 Micro USB cable ZINO000-11 Type C cable ZINO000-12 iphone cable ZINO000-42 Micro USB cable TF card 32G ZINO000-54 ZINO000-55 ZINO200-47 carry bag ZINO200-48 gimbal Card reader ZINO200-49 gimbal coaxial line ZINO200-50 Antenna of remote ZINO200-51 filter 31 Limitation of Liability Hubsan accepts no liability for damages, injuries or any legal responsibi li-ties incurred directly or indirectly from the use of Hubsan products under the following conditions:

1.Damages, injuries or any legal responsibilities incurred when users are drunk, under the influence of drugs or anesthesia, dizzy, fatigued, nauseous and / or affected by other conditions both physical and mental that could impair sound judgment and / or personal ability. 2. Subjective misjudgment and / or intentional mis-operation of products. 3. Any and all mental damage, trauma, impairment, illness, compensation caused / solicited by accidents involving Hubsan products. 4. Product operation in no-fly zones (i.e. natural reserves). 5. Malfunctions or problems caused by modification, refit, replacement or use with non-Hubsan accessories / parts, failure to follow the guidance of the manual in assembly or operaiton. 6.Damages, injuries or any legal responsibilities caused by mechanical failures due to natural wear and tear (aircraft flight time clocking in 100 hours or above), corrosion, aging hardware, etc. 7. Continued flight after low voltage protection alarms are triggered. 8. Knowingly flying aircraft under abnormal conditions (such as when water, oil, soil, sand or other unknown material are inside the X4, the aircraft and /

or transmitter are incompletely assembled, the main compo-nents have obvious faults, obvious defect or missing accessories, etc). 9. Flying in the following situations and / or environments: areas with mag netic interference (such as high voltage lines, power stations, broadcasting towers and mobile base stations), radio interference, govern-ment regulat ed no-fly zones, if the pilot loses sight of the X4, suffers from poor eyesight or is otherwise unsuited for operating Hubsan products. 10. Aircraft use in or exposure to bad weather, such as a rain, wind, snow, hail, lighting, tornadoes and hurricanes. 11. Products are involved in / exposed to collisions, fire, explosions, floods, tsunamis, manmade and / or natural structure collapses, ice, avalanches, debris, landslides, earthquakes, etc. 32 12. The acquisition, through use of Hubsan products (specifically but not limited to aircraft), of any data, audio, video that results in infringement of law and / or rights. 13. Misuse and / or alteration of batteries, product / aircraft circuits, hardware protections (including protection circuits), RC model and battery chargers. 14. Any malfunction of equipment or accessory, including memory cards, that results in the failure of an image or video to be recorded or ot be recorded in a way that is machine readable. 15. Users who engage in reckless, unsafe flying (with or without sufficient training). 16. Non compliance with pre cautions, i nstructions, i nformation an d ope ration guidelines / methods given through official Hubsan website announcements, prod-

uct quick start guides, user manuals, etc. 17. Other losses, damages, or injuries that are not within the boundaries of Hubsan responsibility. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE LOCAL REGULATIONS. HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY. Declaration of Conformity Hereby, SHENZHEN HUBSAN TECHNOLOGY CO., LTD., declares this product is in compliance with the essential requirements and other relevant provisions of Directive 2014 / 53 / EU. A copy of the original Declaration of Confor-

mity can be obtained at the following address: 13th Floor, Bldg 1C, SHENZHEN NANSHAN SOFTWARE INDUSTRY BASE, Xuefu Road, Nanshan District, Shenzhen, China This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to Euro-

pean Directive 2012 / 19 / EU in order to be recycled or dismantled to minimize its impact on the environment. For further information, please contact your local or regional authorities. Electronic products not included in the selective sorting process are potentially dangerous for the environment and human health due to the presence of hazardous substances. 33 FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the local dealer or an experienced radio / TV technician for help. Changes or modifications not expressly approved by the party responsible for com-

pliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interfer-ence that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncon-

trolled environment. This equipment should be installed and operated with a mini-

mum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmit-

ter. Electrical and electronic equipment that are supplied with batteries (including internal batteries) WEEE Directive & Product Disposal At the end of its serviceable life, this product should not be treated as house-

hold or general waste. It should handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal. Internal / Supplied Batteries. This symbol on the battery indicates that the battery is to be collected separately.This battery is designed for separate collection at an appropriate collection point. 34 Please read the operating instructions carefully before use!

Never leave units unattended when charging Unplug the charging cable immediately after charging Propellers may cause injury This product is not a toy Not suitable for children under 14 years of age Flight Academy Product name: ZINO 2 Product Standard Number:Q / HBS 001-2017 Vendor: Shenzhen Hubsan Technology Co., Ltd Address: 13th Floor, Block C, Shenzhen Software IndustrialBase, Xuefu Road, Nanshan District, Shenzhen, Guangdong Province, China Email: service@hubsan.com WWW.HUBSAN.COM

SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2019/12/18 SUBJECT: FCC Application for (FCC ID: 2AN75-ZINO2RX) To Whom It May Concern:

We, the undersigned, hereby authorize Aaron Ma in Shenzhen Huaxia Testing Technology Co., Ltd at 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen Huaxia Testing Technology Co., Ltd on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely,

(Must be signed by the person that is listed on the FCC Website) Signature:

Contact name: Judy Wu Company name: SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Address: 13th Floor, Bldg 1C, Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China 518054 Date: 04/17/2018 VCB_F-01: Operating Procedures Form FCC Authorization v02 Page 1 of 1

SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AN75-ZINO2RX Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type 1. Block Diagram, 2. Schematics, 3. Operational Description File Name 1. 2AN75-ZINO2RX -Block diagram 2. 2AN75-ZINO2RX -SCH 3. 2AN75-ZINO2RX -Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for an initial period of xxxx (ie- 45, 90 or 180) days:

Exhibit Type N/A File Name N/A Signature:

Contact name: Judy Wu Company name: SHENZHEN HUBSAN TECHNOLOGY CO., LTD. Address: 13th Floor, Bldg 1C, Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China 518054 Date: 04/17/2018 VCB_F-01: Operating Procedures Form FCC Confidentiality v02 Page 1 of 1