JM-LL02 LTE CAT M1/NB2 ASSET TERMINAL USER MANUAL(V1.0) CONTENTS 01 02 03 04 05 06 07 08 09 10 11 12
...... ..... Product overview Standard parts list
...... Specication
...... LED indication
...... Charging
...... Product Setup
...... Congure the device
...... Commands list
...... ..... ..... ..... Installation recommendation Web Platform and App Troubleshooting Warranty instructions Maintenance Record 1 01/Product overview Making connections simpler Network indicator GPS indicator Power indicator On/o button Light sensor Magnetic cover joint part Charging port Magnetic contacts Magnetic connector GPS + LBS positioning Real-time location query Geo-fence alert Tamper alert Vibration alert Strong magnet cover 6,000mAh battery powered Magnetic charging IP67 dust and water resistant Bluetooth conguration 02/Standard parts list Item Device Magnetic cover User guide Charger Charge cable Tool Quantity 1 1 1 1 1 1 2 03/Specication Making connections simpler Frequency band LTE M1/NB2B2/B4/B5/B12/B13/B66 GSM850/1900MHz TTFF(opensky) Avg. Cold start: <40sec Avg. Hot start: <1sec Location accuracy
< 10m Dimensions 85 X 58 X 29 mm Weight 6000 mAh,37V Li - Polymer battery Operating Temperature
-20C to+70C Transmit Protocol TCP 04/LED indications Power Status (Red) Quick icker (0.3s on, 0.3s o) Low battery Moderate icker (1s on, 3s o) Fully charged Slowicker (0.1s on, 3s o) Normally working Solid on Solid o GNSS Status (Blue) Charging Low battery voltage or battery failure Quick icker (0. 3s on, 0. 3s o) Searching GPS Slow icker (0.1s on, 3s o) GPS connected successfully Solid o GPS is in sleep mode,or not active Network Status (Green) Quick icker (0.3s on, 0.3s o) GSM initializing Moderate icker (1s on, 3s o) GSM connected successfully Slow icker (0.1s on, 3s o) GPRS online Solid on Calling 3 Solid o No GSM signal/ No SIM card Making connections simpler 05/Charging Please charge the device by original 5V/2A charger. It takes about 3 hours to fully charge the device. Charging LED 06/Product setup Insert SIM card: Please use a screw driver to remove the screws and open the case to insert a SIM card (Size: Nano). Standard Micro Nano Power on: Press and hold the ON/OFF button for 3 seconds, and the LEDs will icker regularly if the device power on successfully. Power o: Press and hold the ON/OFF button for 3 seconds and the LEDs will be o in 2 seconds. 4 Making connections simpler On/o button Note:
1. Press the ON/OFF button and the LED will icker for 15 seconds if the device power on successfully. 2. Press the ON/OFF button and nothing will happen if the device power o successfully. 07/Congure the device Method 1 :
Use your mobile phone to send commands to the device SIM card number by SMS, please refer details of the commands in Commands list section . Method 2 :
1. Download and install the "Jimi loT Lab" app by the following link: http://d.6short.com/lnbr. For iOS 9 and above Only 2. Make sure the Bluetooth is enabled on your iPhone, choose Connect on landing page. JIMI loT Lab M a k i n g c o n n e c t i o n s s i m p l e r Connect JM-LL02_685 14:fc:7c:97:d5:08 Preset Manage preset parameters Connect Connect device with Bluetooth Check Suitable Device
@Design by JIMI loT 5 3. Power on LL02 and then short press the power button for 3 times, the device name will automatically show on Connect page, tap on it to connect. Making connections simpler 4. 5. 6. After the device is connected successfully, you can view the basic data of the device, click "Command mode" button at the bottom can enter the command setting page. Type and send the command to query and and make congurations. The device has no password by default, you can set password (See details in command list) to secure the device. If the password has been set, each command will need to be sent with the password lled. In "Jimi loT Lab" app landing page, you can create a template with multi-
ple commands in Presets page, when the device is connected you can tap the "Upload preset" button instead to send multiple commands that you created in Presets at a lime. 08/Command List Command Usage Instructions APN Set APN ASETAPN Auto set APN APN, ApnName#
or APN, ApnName,User,Password#
Auto set APN will be turned o when set APN manually. APN#
Query current APN ASETAPN,X#
X=ON/OFF, ON:Enable auto set APN, OFF:Disable auto set APN ASETAPN#
Query auto set APN settings 6 ASETGMT Auto set time zone SERVER Platform server setting GMT Time zone setting MODE Set working mode HBT Heartbeat packet interval Making connections simpler ASETGMT,<X>#
X=ON/OFF, ON:Enable auto set time zone, OF:Disable auto set time zone ASETGMT#
Query auto set lime zone settings SERVER, 1,domain name,port#
SERVER,0,IP,port#
Default:SERVER, 1,GPSDEV. TRACKSOLID.COM,21102#
SERVER#
Check the current sever settings GMT,A,B,C#
A:E/W; E for eastern, W for western;
Default: E B:0-12, time zone;Default:8 C:0/15/30/45; half time zone;
Default:0 GMT#
Query current time zone setting MODE,A,T1 ,T2#
A=1-2;1:Tracking mode, 2:Ultra power saving mode;Default:1 When A=1, T1:Report interval of GPS data in moving status, range:
10-3600 seconds; default: 10 T2:Report interval of GPS data in static status, range:180-86400 seconds;default:0 When A=2, T1:start time of the report, format:HH:MM T2:time interval, range:1-72 hours, default:24 MODE#
Query the current working mode setting HBT,T#
T=1-10 minutes, heartbeat packet interval, Default:3 Minutes;
HBT#
Query the current heartbeat interval 7 PWDSW Set command password Making connections simpler PWDSW,A#
A=ON PWDSW,A,B#
A=Numbers and alphabets, 1-19 digits;Default:666666 B=OFF When PWDSW is ON, all the command has to send with the password as the rst parameter, e.g.:MODE,666666, 1,30,30#
PWDSW#
Query current password selling PASSWORD Modify command password PASSWORD,A,B#
A=Old password, Default:666666 B=New password CENTER Set center number CENTER,A,Number 1,Number 2, Number 3#
Add center number CENTER,D, 1, 2, 3#
Delete center number according to the serial ID CENTER,D,Number#
Delete center number according to the matched number CENTER#
Query the current center number PWRLIMIT Power OFF limitation PWRLIMIT,ON #
X=ON/OFF;ON:Not allow to power o with the device button, OFF:
Allow to power o with the device button;
PWRLIMIT#
Query the current PWRLIMIT setting RESET Reboot the device RESET#
The device will reboot in 20 Seconds when receive this command FACTORY Recover the settings to factory FACTORY#
Recover all the settings to factory
(Except server and APN) Query the current center number 78 Making connections simpler PARAM GPRSSET Query device parameters Query platform server and APN Setting STATUS Query status 09/Installation recommendation Under rear windshield Under front windshield Around dashboard 1. The device should face up to the sky. 2. Metal thermal barrier or heating layer of the windshield aects the signal. Please change installation position to receive better signal. 10/Web Platform & App 1. Please login the designated service platform provided by your distributor to track and operate the device 2. Please download and install the APP in designated website, iOS App store or Google Play store. 89 Making connections simpler 11/Troubleshooting Type Use Unable to connect to tracking platform Tracker shows oine Unable to locate Unable to boot No command reply Check theAPN and IP settings. Check whether the data service of SIM card is enabled. Check the balance of SIM card. Check if the device entered network blind area. Check the balance of SIM card. Make sure the top side facing upward without metallic things shielded. Make sure it's not in area with no satellite coverage. Check whether the battery is exhausted. Check whether the SIM card is inserted. Make sure command format is correct. Vehicle may be in network blind area. 12/Warranty instructions and service 1. The warranty is valid only when the warranty card is properly completed, and upon presentation of the proof of purchase consisting of original in-
voice indicating the date of purchase, model and serial No.of the product We reserve the right to refuse warranty if this information has been re-
moved or changed after the original purchase of the product from the dealer. 2. Our obligations are limited to repair of the defect or replacement the de-
fective part or at its discretion replacement of the product itself. 3. Warranty repairs must be carried out by our Authorized Service Centre. Warranty cover will be void, even if a repair has been attempted by any unauthorized service centre. 4. Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty period. 5. The warranty is not applicable to cases other than defects in material, design and workmanship. 810 Making connections simpler Serviced by Maintenance Record Date Product Model IMEI Number Fault Descriptions Comments 811 FCC Compliance Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.