Bietrun WXM30 UHF Professional 8-Channels Rechargeable Wireless Microphone System User manual If you have any questions, please feel free to contact us. E-mail: amazon@bietrun.com 1 1. Product introduction This UHF Professional 8-Channels Rechargeable Wireless Microphone System uses UHF frequency band transmission, which has the characteristics of long transmission distance, strong anti-interference ability, low delay, and clear sound quality. It is easy to use and operate. Note: Please read and follow all warnings carefully before use, and keep this manual for subsequent use. 2. Product description Microphones Display CH 1 CH 2 CH 3 CH 4 botton No. Part Name Micropho ne Display Power Function Description Notes Pickup voice
(1)Information about microphone: power, signal, channel, volume, microphone 1-8;
(2)Only battery level will be displayed after 5 seconds of no operation on the microphone.
(1)Power on/off: short press to turn on, press 2S to turn off;
(2)Volume: Short press to adjust the volume in turn. 1-5 levels, level 1 is the smallest, level 5 is the largest. 2 Press this button to adjust the channel. External DC 5V power supply charges the product.
(1)Green: microphone is on;
(2)Red flash: low power;
(3)Red: charging; Red light is off when fully charged. Press this button to switch channels when the connection is unstable.
(1)Charge it once before your first use;
(2)Charge it with low power. Channel Charging port Indicator light Receiver Front Di sp la y Signal Frequency Mic ID Power 3 Back No. Part Name Power Function Description Short press to turn on, long press to turn off Notes Channel Display Display connection information of Microphone 1-8 When the mic is not turned on, the "--"
on the display of the channel flashes in sequence. volume Adjust volume of mic 1-8:Turn left to decrease the volume, turn right to increase the volume. Antenna Receive wireless signals from microphone 123456 78.
(1)Please tighten the nut to the right of the antenna before turning it on for the first time
(2)When connection is unstable and sound is intermittent, you can adjust the antenna direction to improve it. 4 21 Microphone Output 6.35mm audio output XLR output port of mic 1-8 This port only outputs the audio signal of its own microphone 6.35mm audio output interface Charging port Input voltage is DC 12V The audio is a mixture of microphone 1-8 Please use the adapter provided with the product 3. Connection 3.1 Input Connection 3.2 Output Connection When the microphones and receiver are turned on, They will be automatically paired. Audio amplifier devices with XLR interface, 6.35mm audio input interfaces can be connected to this product, including mixers, multimedia speakers, Bluetooth speakers, power amplifiers, and lever speakers. 5 XLR XLR 6.35 XLR Mixing console Multimedia Bluetooth Speaker XLR PA 6 XLR audio output and 6.35mm output can not be connected to the same devices, otherwise the sound may Note:
not be played normally. 4. FAQ 3 No sound 4 Small sound 5 6 Intermittent sound Howling or screaming 5. Parameter Receiver No. 1 Problems Receiver cant be turned on 2 Microphones cant be turned on Solutions
(1)Check whether the power is turned on,
(2)Check whether the adapter and cable are connected with the receiver correctly and firmly.
(1)Charge first and check whether the mic charging indicator is on;
(2)Short press the power button to turn on.
(1)Check whether the volume of the microphone, amplifier and Bluetooth devices have been turned on;
(2)Check whether the microphone is successfully connected to the receiver, the display will be on if the connection is successful;
(3)Turn up the volume of the receiver;
(4)Check whether the XLR interface and 6.35 interface are connected correctly;
(5)The amplifying device may need to set the input mode, please refer to the manual of the amplifying device for setting;
(1) Adjust the VOL button on the microphone to increase the volume, 1 is the minimum , 5 is the maximum
(2)Turn the knob to the right to increase the microphone volume on the receiver
(3)Turn up the volume of the amplifier.
(1)Shorten the distance between the microphone and the receiver(within 30M, No obstacle)
(2)Switch channel
(1)Reduce the volume of amplifier or microphones;
(2)Dont place the microphones too close to the speaker. 7 Receiving frequency: U Band Frequency stability: <0.005%
Sensitivity: 2mV Interference frequency ratio > 90dB Image interference ratio: >88dB Signal to noise ratio: >95dB Audio output: 800mV-1.4V Working range: Standard conditions 30 to 50 m Receive channel: 4 Supply Voltage: DC 12V Power consumption: 3W Antenna: universal antenna Handheld Transmitter Carrier frequency: U Band Transmit power: 10mW Harmonic: <Main wave 40dB Pickup: 600single directivity Antenna: built-in Complex Index Frequency stability: <0.005%
Current consumption: <25mA Standard: Fixed frequency Battery: lithium battery Supply Voltage: DC 5V Dynamic Range: >95dB System distortion(<1%1K Hertz modulation Frequency response: 50Hz-18KHz(+3dB) 6. Packing List 8X Microphone (12345678 1X Receiver 4X Microphone Antenna 1X 6.35mm to 6.35mm cable 2X Charging cable 1X Adapter 1X Manual 8 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
connected. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 9