FCC ID: 2A5Z8-K2 Garage door wireless keypad

Universal Garage Door Wireless Keypad K2 Manual V3.0 Please read instructions thoroughly BEFORE beginning. Start with garage door CLOSED. Install the battery and program the keypad prior to installation. Determine your garage door opener type has Smart/Learn Button or DIP Switch, they are located on motor unit or external receiver. Our Universal Keyless Entry Keypad can programmed the Chamberlain, Sears Craftsman, Liftmaster, Mechanic, Do It, Genie Intellicode, Overhead Door, Stanely, Wayne Dalton, Linear etc major brand garage door openers.It has 2 channels can control up 2 garage door independently. NOTE: Factory set PIN Code 1111# for 1st channel, 2222# for 2nd channel. If you want to change the factory set PIN code before programming, please go to next page "Change an Existing PIN Code". DETERMINE GARAGE DOOR OPENER TYPES:

Proceed with instructions according to your garage door opener type. NOTE: Your motor unit and/or remote control may look different. TYPE 1 Chamberlain, LiftMaster, Sears Craftsman, Master Mechanic, Do It, Stanley, Genie Intellicode, Overhead Door, Wayne Dalton and Linear etc garage door openers with: Smart/Learn Button . TYPE 2 Chamberlain, LiftMaster, Genie, Sears Craftsman, Master Mechanic, Do It, Moore-O-Matic and Linear etc garage door openers with: DIP Switches . Opener Learn LED Learn Button Programming TYPE 1 1. Press and hold the and button at the same time for enter into program model. 2. Press button 1# OR 2# of your choice.

NOTE: 1# mean enter program for 1st channel, 2# mean enter program for 2nd channel. 3. Enter your opener ID _ _ end up with #. Determine your opener ID using the Brand List chart 1.

* For example program the opener type Chamberlain green button corresponding the opener ID is 04, so enter 04#. 4. Press and release the Learn Button on the garage door opener within 1 minute. 5. Enter a 4-digit factory set PIN Code 1111# OR 2222# of your choice. NOTE: Factory set PIN code 1111# for 1st channel, 2222# for 2nd channel.

* NOTE: For Genie and Overhead Door Opener are special,you should press the PIN code twice. Such as press your existing PIN Code 1 time _ _ _ _#, then press again _ _ _ _#. 6. To test,enter the PIN Code with # again. Then the garage door opener will activate.

* To program another channel,please repeat above steps with a new PIN Code for different opener.

* For safety, please go to next page "Change an Existing PIN Code" after programming. 1 2 4 The Learn LED will light on within 30 seconds... 5 1 4 7 2 5 8 0 3 6 9

1 4 7 2 5 8 0 3 6 9

Learn Button _ _ _ _ PIN Code

1 4 7 2 5 8 0 3 6 9

Programming TYPE 2 Opener 3 Opener ID 01 02 03 04 05 06 07 08 09 2 Position DIP Switch OR 3 Position DIP Switch Brand Linear Chamberlain Chamberlain Chamberlain Genie Overhead Door Genie Overhead Door Stanley Chamberlain Wayne Dalton Type/Learn Button MegaCode 318MHz 1997-Current Red/Orange button 390MHz 1997-2005 Purple button 315MHz 2005-Current Green button 390MHz 1993-1996 Intellicode 315MHz 1995-Current Intellicode 390MHz 2005-Current Security code 310MHz 1998-Current Yellow button 310/315/390MHz 2011-Current Rolling code 372.5MHz 1999-Current Chart 1 6 1 4 7 2 5 8 0 3 6 9

i c k C l i c k C l For some old garage door opener/receiver that using the DIP switches system has 2 position or 3 position with switches number between 1-12. If your existing opener/receiver with 3 position switches, you MUST set them in or location first,do not use the 0 position.

opener opener 2 position DIP switches 3 position DIP switches Leave the middle switch locations blank. 1. Press and hold the and button at the same time for enter into program model. 2. Press button 1# OR 2# of your choice.

NOTE: 1# mean enter program for 1st channel, 2# mean enter program for 2nd channel. 1 2

1 1 4 4 7 7 2 2 5 5 8 8 0 0 3 3 6 6 9 9

1 4 7 2 5 8 0 3 6 9

4. Enter the Keypad button for match your existing openers.

If your opener with 2 Position DIP Switches,the DIP switch is in the position place a 2, position place a 8, end with button # . Note the numerical value in order of the DIP switch locations. Then the garage door opener will activate. Such as program opener with 2 Position 12 DIP Switch ON-OFF-OFF-OFF-

ON-ON-ON-OFF-OFF-OFF-OFF-OFF,corresponding press the button 2-8-8-8

-2-2-2-8-8-8-8-8.(Fig.1) If your opener with 3 Position DIP Switch,just leave the middle switch locations blank,then proceed as above. (Fig.2)

* The DIP switch locations and the keypad button MUST be match

"On/ "=2, "Off/ "=8.

3. Enter your opener ID _ _ end up with #.

* For example program the opener type Chamberlain 8 DIP Switch 310MHz corresponding the opener ID is 14, so enter 14#.(Determine your opener ID using the Brand List chart 2.) Fig.1 OR Fig.2 3 Opener ID Brand Type/Dip Switch Opener ID Brand Type/Dip Switch 10 11 12 13 14 Chamberlain Chamberlain Genie 9 DIP Switch 390MHz 1990-1992 9 DIP Switch 315 MHz 1983-1989 12 DIP Switch 390MHz 1985 Linear Multi code 10 DIP Switch 300MHz Chamberlain 8 DIP Switch 390MHz 15 16 17 18 Stanley Multi code Genie Linear Moore-O-Matic Chamberlain 10 DIP Switch 310MHz 9 DIP Switch 390MHz 8 DIP Switch 310MHz 7 DIP Switch 390MHz Chart 2 5. Enter a 4-digit factory set PIN Code 1111# OR 2222# of your choice. NOTE: Factory set PIN code 1111# for 1st channel, 2222# for 2nd channel. NOTE: For Genie and Overhead Door Opener is special,you should press the PIN code twice. Such as press your PIN Code 1 time _ _ _ _#, then press again _ _ _ _#. 6. To test,enter the PIN Code with # again. Then the garage door opener will activate.

* For safety, please go to next page "Change an Existing PIN Code" after programming. Change an Existing PIN Code 1. Press and hold the and button at the same time for enter into program model. 2. Enter a 4-digit factory set PIN Code 1111# OR 2222# of your choice.

1 1 1 4 4 7 7 2 2 5 5 8 8 0 0 3 3 6 6 9 9

2 1111#

OR 2222#

3 1 4 7 2 5 8 0 3 6 9

_ _ _ _ new PIN Code

1 4 7 2 5 8 0 3 6 9

NOTE: Factory set PIN code 1111# for 1st channel, 2222# for 2nd channel. 3. Enter a 4-digit new PIN Code _ _ _ _ end up with # button for confirm.

* The new PIN code you set MUST be remembered !

Operation instructions Opener activits 4-digit password and # enter button is pressed. If wrong numbers are accidentently pressed, correction can be made immediately. The # Enter button will transmit only the last four digits. The keypad will exit the programming mode if the keypad did not receive any commands within 6s. Factory default set Wireless Keypad with beep alarm and back indicator light. When programming, if user key in users PIN Code more than 4 digits, the keypad would recognize it as incorrect operation,then exit programming mode. Keypad allows two attempts of wrong entire pin codes. After the third wrong entire pin codes key-in, the keypad will be locked for 2 minutes with 3 beeps and red LED light goes on. 2 minutes later, keypad would have one beep sounds and red. LED indicator goes off to indicate the user keypad is unlock. Factory Reset If you get something wrong when program or entry PIN Code and can not proceed with any operation, you could reset the keypad. Remove the battery cover and you will see a Reset Button. Press and hold the reset button for about 5s a beep sound to confirm the keypad has been reset successfully. RESET BUTTON Now the keypad has restore Factory Set model with PIN Code 1111# for 1st channel and 2222# for 2nd channel. Trouble Shooting Q: Why won't my keypad work?

1 Installation Select a location to mount the Keypad at a minimum height of 5 feet (1.5m) out of the reach of Children. Remove battery cover and battery. Mark the top mounting hole and drill 1/8 inch(3.2mm) pilot hole. Install the top screw, allowing 1/8 inch (3.2mm) to protrude above the surface. Position the keypad over the top screw. 2 4 3 5 6 Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom screw. Do not overtighten to avoid cracking the plastic housing. Re-install battery and replace cover. Battery Replace the 9-Volt battery when keypad light becomes dim or does not light up. Slide cover up, remove battery cover, and replace battery. Re-programming maybe necessary. 9V Battery

- Did the keypad lights come on when you entered your PIN ? If the keypad lights do not turn on when you press a button, it indicates that the battery needs to be replaced. Replace with a 9V battery.

- Try reprogramming the keypad to the garage door opener.

- Make sure the keypad is compatible with your garage door opener. Q: Will I have to reprogram the keypad after changing the battery?

- The keypad should retain its memory.If the keypad no longer operates the operator.Reprogram the keypad to your system. Q: Where is my Learn Button or DIP Switches on my gate/garage?

- Locate the Learn Button or DIP Switches on the garage door opener/receiver.Most garage openers have a built-in radio receiver or an external receiver. Q: Can I program the keypad to a second garage door opener?

- Yes. Our garage door keypad can support 2 garage door opener independently. Q: How can I reset the keypad when I forgot the entry PIN code ?

- Remove the battery cover and you will see a Reset Button. Long press the Reset Button about 5s,you will heard a beer,now it has been resettled successfully . WARNING WARRANTY To prevent possible SERIOUS INJURY from a moving garage door :

One Year Limited Warranty. Install Keypad within sight of garage door,out of reach of children at a minimum height of 1.5m above floors, landings,steps or any other adjacent walking surface,and away from ALL moving parts of door. Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. NEVER permit children to operate or play with Keypad. ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. If battery is swallowed, immediately notify doctor. Thank you for purchasing our products Our products are covered 1 year limited warranty from the date of its original purchase. If any problems occur, please contact us for help. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC ID: 2A5Z8-K2 Page 1 of 1 Report No.: CTL2207281021-WF FCC ID Label Information Label location:

Garage door wireless keypad Model: K2 FCC ID: 2A5Z8-K2 Size:40*30mm

Shenzhen Jos Technology Co., Ltd. Agent Authorization Company: Shenzhen Jos Technology Co., Ltd. Address: 1101, No. 4, Lane 13, Huaqiao New Village, Jingbei Community, Xixiang Street, Baoan District, Shenzhen, China Product Name: Garage door wireless keypad Model Number(s): K2 Product Description: Garage door wireless keypad We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Joshua Zhang Title:

CEO Company: Shenzhen Jos Technology Co., Ltd. Date: Sep. 06,2022

Shenzhen Jos Technology Co., Ltd. 1101, No. 4, Lane 13, Huaqiao New Village, Jingbei Community, Xixiang Street, Baoan District, Shenzhen, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2A5Z8-K2 Date: 2022/09/06 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Joshua Zhang Title: CEO

Shenzhen Jos Technology Co., Ltd. 1101, No. 4, Lane 13, Huaqiao New Village, Jingbei Community, Xixiang Street, Baoan District, Shenzhen, China Responsibility Declaration Letter Company name: Shenzhen Jos Technology Co., Ltd. Address: 1101, No. 4, Lane 13, Huaqiao New Village, Jingbei Community, Xixiang Street, Baoan District, Shenzhen, China Product Name: Garage door wireless keypad FCCID: 2A5Z8-K2 Model(s): K2 We, [Shenzhen Jos Technology Co., Ltd.], hereby acknowledge that all the product information (including all original, drafted, or modified documents) provided to the TCB either by us or our agent or representative(s)for the purposes of FCC certification will meet FCC regulations and requirements; and that any modifications or changes made as a result of TCB review of the documents will be formally implemented into the manufacturing process and product documentation shipped with equipment. We also confirm that all information provided is legitimate and does not contain any false content such as forgery, fabrication, alteration, tampering and concealment. We assume all economic and legal responsibilities in matters that may arise as a result of disclosure on sample products and associated product documentation provided for product certification that may subsequently be found to be a mis-representation of the final product and accompanying documentation when produced, marketed, or sold in the United States, Canada, or anywhere in the world. Your sincerely, Name: Joshua Zhang Title and Company name:

CEO / Shenzhen Jos Technology Co., Ltd. Date: Sep. 06, 2022 Signature of FCC grant holder (Include Title, Company name, date, and official company stamp):

Responsibility Declaration Letter v1.0