FCC ID: 2AQY4-33A Smart Lock

Bluetooth Keypad Deadbolt Smart Lock User Guide / Installation Instruction Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade. User Guide Installation Instruction P1 P2 P3 P4 Quick Start Guide At a Glance How to Lock/Unlock Denitions P6 P7 P8 Installation Instruction P13 STEP 5: Door Handing Part list P14 Programming STEP 1: Prepare the door and check dimensions P16 Factory Default Settings P9 STEP 2: Install the latch and strike P17 Troubleshooting P5 Code Format P11 STEP 3: Install the exterior assembly P18 FCC Statement P12 STEP 4: Install the interior assembly P19 Warnings IMPORTANT:

The App is required to operate the lock. After the lock is properly installed, the first account to bind the lock will be the administrator. QUICK START GUIDE 1 3 1 App Scan the QR Code to download the App. Follow the installation instructions to install the smart lock. 2 4 Register and login to the App. Add the device to your account by scanning the QR Code found on the Battery Cover. Complete the Bluetooth setup in the App. At a Glance Exterior Assembly Interior Assembly Keypad Battery Cover Emergency Key Override Button Keyhole 1. Pull the exterior assembly from the button. 2. Rotate from the top to open it, insert the key and rotate to unlock. Reset Button Multifunction Button Thumb Turn 2 How to Lock / Unlock Unlocking the door from outside Unlocking the door from inside Master/

User PIN Code Key App App Rotate the thumb turn to the unlock position. App App Locking the door from outside Locking the door from inside Manually Press any button on the keypad for 2 seconds to lock the door. Auto Lock Mode In Auto Lock Mode, the latch bolt is automatically extended after unlocking. Key App App Manually Rotate the thumb turn to the lock position. Auto Lock Mode In Auto Lock mode, the device will be locked automatically. App App 3 Definitions Master PIN Code Required for programming and feature settings, the Master PIN Code can be used to unlock the door while in vacation mode. The default Master PIN Code needs to be changed before programming the lock for security reasons. Auto Lock If the Auto lock feature is enabled, the lock will lock the door 30 seconds after it has been unlocked. This feature is off by default. You can set the time delay for 30s, 60s, 120s and 180s in both Master Mode and the App. Wrong Entry PIN Code Limit After 10 attempts of entering an invalid User PIN Code, the unit will shut down for 3 minutes. Silent Mode The keypad will beep when pushed; but can be muted. Low battery and Wrong Entry User PIN Code Limit alarms will still sound in Silent Mode. Low Battery Alarm If the battery indicator keeps flashing, the batteries are getting low. For the best performance replace with four new AA alkaline batteries. Unlock With Fake Code Users can prevent PIN Code exposure from strangers by entering random digits before or after the correct PIN Code. PASSWORD RANDOM DIGITS 4 Code Format 1. Master PIN Code (4 to 10 digits): The default Master PIN Code is 12345678. Change the default Master PIN Code before programming other codes. 2. User PIN Code (4 to 10 digits): A total of 20 User PIN Codes (including One-Time PIN Code) can be programmed and stored in the lock. 3. Both Master and User PIN Codes do not support the following combination of numbers. Forward number sequence Backward number sequence Repeat number sequence Contain existing code sequence 5 INSTALLATION INSTRUCTION Interior Assembly (G) Battery Cover (L) Mounting Plate (E) Exterior Assembly Screw (F) (Optional) Exterior Assembly

(B) Latch (C) Mounting Plate Screws (J) Backup Key (A) Latch Screws

(I) Strike Plate Screws (H) Strike Plate (D) Interior Assembly Screws (K) Reinforcement Plate (D-1) (Optional) 6 Parts List A Backup Key x2 B Exterior Assembly x1 C Latch x1 D Strike Plate x1 2 2 C-1 Drive-In Collar (Optional) Reinforcement Plate x1

(optional) E Mounting Plate x1 F Exterior Assembly Screw (Optional) G Interior Assembly x1 H Strike Plate Screws x2 I Latch Screws x2 J Mounting Plate Screws x2 K Interior Assembly Screws x3 L Battery Cover x1 M Reset Tool

(35mm<door thickness<50mm) 7 Prepare the door and check dimensions STEP 1 A Measure to confirm that the bore hole is 1-1/2 or 2-1/8"

(38mm or 54mm). Measure to confirm that the hole in the door edge is 1"

(25mm). C Measure to confirm that the door is 1-3/8"

to 2" (35mm to 50mm) thick. 2-3/8" or 2-3/4"

(60 or 70mm) B Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60 or 70mm) 1-1/2" or 2-1/8"

(38 or 54mm) 1"

25mm 1-3/8" to 2"

(35mm to 50mm) D Make sure the hole in the door frame is drilled a minimum of 1

(25mm) deep, to leave enough space for the deadbolt to extend into the door frame when the door is locked. 1 "

2 5mm Notes:

Make sure the door frame is aligned with the door and there are no obstructions stuck in the door frame. 8 STEP 2 Install the latch and strike A Determine backset and adjust the latch. YES No adjustment is required. Proceed to next step. NO Slotted hole is NOT centered. Rotate and pull the latch as shown to extend latch. up Latch Screws (I) Hold the latch in front of the bore hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?

B Install the latch. Chiseled Not Chiseled 9 2-3/8"

0

(6 m m) Drive-In Collar

(C-1) p ull

(70m 2-3/4"

m) C Use a screwdriver to test if deadbolt works smoothly. D Install strike on the door frame. IMPORTANT:

Make sure the hole in door frame is drilled a minimum of 1" (25mm) deep. Strik e Plate S cre w s H) D

(Optional) 10 STEP 3 Install exterior assembly IMPORTANT:

Before installation, make sure the latch is fully retracted (in the unlocked position). A Measure the diameter of the hole in the door. Unlocked Locked 1-1/2" or 2-1/8"

(38 or 54mm) C Secure the mounting plate with the supplied screws. Do not overtighten screws. B With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the tailpiece through the slot in the latch. Tailpiece 11 1-1/2" (38mm) Remove the spacer 2-1/8" (54mm) Proceed to next step Exterior Assembly Screw(Optional) Mounting plate Screws(J) Keep parallel to door edge. STEP 4 Install interior assembly A Push the battery cover up in the direction as illustrated. B Insert the cable into the connector. Push the connector in firmly until it is completely attached. C Keep the thumb turn in the vertical position and install the interior assembly. Horizontal Unlocked D Attach interior assembly to mounting plate and tighten 3 screws. E Load 4 AA (1.5V) batteries (Not included) into the battery compartment. Interior Assembly Screws (K) 12 STEP 5 Door Handing IMPORTANT:

This step is required and crucial for the lock after installation. A While keeping your lock unlocked, insert 4 AA alkaline batteries into the battery pack. B Use the Reset Tool to press and hold the Reset Button for more than 5 seconds until you hear a long "BEEP". C If the reset is successful, the latch bolt will extend on its own to learn the handing orientation of the door. Reset Button RES 13 Programming IMPORTANT:

The default Master Code is 12345678 . It is required that you change it to a code of your own before programming. Change Master PIN Code Add User PIN Code Delete User PIN Code

Master PIN Code

Master PIN Code

Master PIN Code

Press 1 New Master PIN Code +

New Master PIN Code +

Wait for green light to flash Wait for green light to flash Green light will flash Press 2 New User PIN Code +

New User PIN Code +

Wait for green light to flash Wait for green light to flash Green light will flash Press 3 Unwanted User PIN Code +

Wait for green light to flash Successful Green light will flash 14 Silent Mode Auto Lock

Master PIN Code

Press 6 Wait for green light to flash

Master PIN Code

Press 7 Wait for green light to flash

+1

+2

+1

+2

+3

+4

+5 Silent Mode disabled when green light flashes Silent Mode enabled when green light flashes Auto Lock disabled when green light flashes Auto Lock 30s enabled when green light flashes Auto Lock 60s enabled when green light flashes Auto Lock 120s enabled when green light flashes Auto Lock 180s enabled when green light flashes Away Mode

Master PIN Code

Press 8 Wait for green light to flash Press Away Mode Enabled 15 Factory Default Settings How to Reset?

Resetting the device will delete all User PIN Codes and Master PIN Code stored in the lock. Step 1. Keep the door open and the lock unlocked (thumb turn will be vertical). Step 2. Using the Reset Tool, press and hold the Reset Button for 5 seconds until you hear the

"BEEP" and the latch extends out automatically. Settings Master Code Auto Lock Silent Mode Wrong Code Entry Limit Shutdown Time Away Mode Factory Defaut 12345678 Disabled Disabled 10 times 3 Minutes Disabled Reset Button RES 16 Troubleshooting Problem Solution Make sure the backset on the latch is set to the proper length.Refer to Installation Guide. The latch does not operate correctly after installation. Lock does not smoothly lock or unlock while using the thumb turn. Make sure prior to installation the latch bolt is retracted. Refer to Installation Guide. Please restore to factory default setting and enter the default Master PIN code to set up the lock. Refer to User Guide. Confirm the proper mounting screws are installed. Make sure the lock is installed correctly. Lock set up failed. Insert fresh batteries and make sure that the cable is properly connected, not pinched. After installation, reset the lock to the factory default settings. Make sure batteries are inserted correctly. Keypad not responding. If the battery indicator flashes continuously, the batteries are low. Replace them with four new AA alkaline batteries. Make sure that the cable is properly connected and has not been damaged during installation. Master PIN Code cannot be changed. I forgot my Master PIN Code. Auto Lock is not working. Refer to the Quick Start Guide to reset the lock and reprogram all PIN Codes. Perform a factory reset to clear all PIN codes. Once the reset is complete, all PIN Codes will be deleted and the Master PIN Code will be reset to the default Master PIN Code of 12345678. If the battery indicator blinks continuously, the batteries are weak. Replace them with four new batteries to get the best performance (alkaline batteries only). Refer to the Quick Set Up to activate the Auto Lock function. 17 FCC Statement This equipment has been tested and found to comply with the limits for a Consult the dealer or an experienced radio/TV technician for help. Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. interference to radio or television reception, which can be determined by RF Exposure Information turning the equipment off and on, the user is encouraged to try to correct This equipment complies with FCC radiation exposure limits set forth for an the interference by one or more of the following measures:

uncontrolled environment. This equipment should be installed and operated Reorient or relocate the receiving antenna. with minimum distance 20cm between the radiator and your body. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 18 Warnings Failure to follow the below instructions could result in damage to the Do not install batteries until the lock is completely installed on door. product and void the factory warranty. This manufacturer advises that no lock can provide complete security by itself. User PIN Codes: Can be 4-10 digits and can be set up in the App. Sharing Access: Sharing access to your lock means that you are allowing other users to control and track usage of the device. Please be aware of This lock may be defeated by forcible or technical means, or evaded by the potential risks it may cause. entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Product Care:

This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing. Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock. 19 V1.0

Label Location On EUT 1.5cm 3.5cm FCC ID: 2AQY4-33A ESN: VE13222000001 BT MAC: AA:BB:CC:DD:EE:FF SN: KBW2309VE1B12345 Brand: Veise Model: VE33A ESN/BT MAC ESN13SN16

Shenzhen Kaadas Intelligent Technology Co., Ltd. Attestation Statements C5266091_X24_Ed.2 TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization Applicant Company name: Shenzhen Kaadas Intelligent Technology Co., Ltd. Grantee code: 2AQY4 FCC ID: 2AQY4-33A Contact Name: Jing Rao Address:

Xili Street, Nanshan District, Shenzhen, Guangdong, 518000, China Telephone No:

Fax No:

Email: chenyutong@kaadas.com FRN: 0027791201 0755-86668868 0086-0755-86958295 Floor 11, Building B2, Phase 2, Creative City, Xiandong Road, Xili Community, i. ii.

[Shenzhen Kaadas Intelligent Technology Co., Ltd.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification.

[Shenzhen Kaadas Intelligent Technology Co., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification.

[Shenzhen Kaadas Intelligent Technology Co., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing coveredequipment . Date: 2023/12/21 Applicants Name: Jing Rao Title: Manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

Shenzhen Kaadas Intelligent Technology Co., Ltd. C5266091_X10_Ed.2 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AQY4-33A To Whom It May Concern, Date: 2023.12.21 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No NOTE 1 NOTE 1 No No Short-Term Confidentiality NOTE 2 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature:

Name: Jing Rao Title: Manager 1/1

Shenzhen Kaadas Intelligent Technology Co., Ltd. Declaration on Model Differences We, Shenzhen Kaadas Intelligent Technology Co., Ltd. Floor 11, Building B2, Phase 2, Creative City, Xiandong Road, Xili Community, Xili Street, Nanshan District, Shenzhen, Guangdong, 518000, China Declare that the following product(s):

FCC ID: 2AQY4-33A Product Name:Smart Lock Model No.: VE33A, VE33B, KA33A, KA33B We(Shenzhen Kaadas Intelligent Technology Co., Ltd.) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/ circuit.antenna type(s) and antenna location.components on PCB,etc.,),Same mechanical structure and design including product enclosure, materials, etc.,), the difference is the model name, trade mark and fingerprint function. Please refer to the following:

Model No. VE33A VE33B KA33A KA33B Trade mark function No fingerprint function With fingerprint function No fingerprint function With fingerprint function The manufacturer would take all the responsibilities for the above product(s). For and on behalf of Authorized person Rao jing Manager Shenzhen Kaadas Intelligent Technology Co., Ltd. Date of issue: 12/25/2023

*I hereby declare that I am entitled to sign on behalf of the applicant and that the information supplied is correct and complete.

C5266091_X8_Ed.1 Shenzhen Kaadas Intelligent Technology Co., Ltd. Letter of Authorization Company: Shenzhen Kaadas Intelligent Technology Co., Ltd. Address: Floor 11, Building B2, Phase 2, Creative City, Xiandong Road, Xili Community, Xili Street, Nanshan District, Shenzhen, Guangdong, 518000, China Product Name: Smart Lock Model Number: VE33A, VE33B, KA33A, KA33B FCC Identifier: 2AQY4-33A We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Jing Rao Date: 2023.12.21 Title: Manager Signature of applicant:

1/1