FCC ID: 2A9SE-KRG096 KRG096 Remote control

Specification of REMOTE CONTROL KRG096 1. This program uses CMT2150A wireless transceiver chip as the control and transmission unit. It integrates the 1527 encoding format inside. 2. After pressing any of the 8th, 9th, 10th, and 11th pin switches of CMT2150A, that is, after pressing the S1, S2, S3, and S4 keys, the level of the corresponding pin port changes, and CMT2150A calls programming after obtaining the pin change After the corresponding parameters, the corresponding low-frequency signal modulation is completed internally, and after being mixed with the 433.92MHz high-frequency signal amplified by the external 26MHz crystal oscillator local oscillator signal, it is sent out through the antenna. 3. Parameter:

Working Current12mA Frequency433.92MHz ModulationASK Temperature-20-55 Dimension72*38*16mm Encode type: Learning code/Rolling code BatteryCR2032(3V) Distance:45m Working Mode:

1. Non-lock/Momentary: Press remote button A, the corresponding relay on the receiver is on;

release button A, the relay is off, the same as others. 2. Self-lock/Toggle: Press remote button A, the corresponding relay on the receiver is on; press button A again, the relay is off, the same as others. 3. Inter lock/Latching: Press remote button A, the relay A is on, B is off; press button B, the replay B is on, A is off. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receivingantenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Page 1 of 1 FCC ID: 2A9SE-KRG096 LABEL AND LOCATION KRG096 Remote control Model: KRG096 FCC ID: 2A9SE-KRG096

(Size: L 2.0cm x 1.5cm) Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

C5266091_X24_Ed.1 Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization Applicant Company name: Shenzhen Kelvin Electronics Co,.Ltd Grantee code: 2A9SE FCC ID: 2A9SE-KRG096 Contact Name: Pang Diana Address: 4/F, 23/B, Lianchuang Technology Park, Bulan Road, Nanwan Street, Longgang District, Shenzhen China Telephone No: 18878479860 Fax No: /

Email: sales2@cnkelvin.com i. ii.

[Shenzhen Kelvin Electronics Co,.Ltd] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification.

[Shenzhen Kelvin Electronics Co,.Ltd] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification. Date: 2023/03/15 Applicants Name: Diana Pang Title: Sales Manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

Shenzhen Kelvin Electronics Co,. Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2A9SE-KRG096 To Whom It May Concern, C5266091_X10_Ed.2 Date: 2023-03.16 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No NOTE 1 NOTE 1 No No Short-Term Confidentiality NOTE 2 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, 1/1 C5266091_X10_Ed.2 Signature:

Name: Diana Pang Title: Sales Manager 2023.03.15 1/1

Shenzhen Kelvin Electronics Co,. Ltd Product Similarity Declaration Product name: KRG096 Remote control Model name: KRG096, KRG095, KRG093, KRG092, KRG091, KRG090, KRG089, KRG088, KRG087, KRG086, KRG085 FCC ID: 2A9SE-KRG096 We (Shenzhen Kelvin Electronics Co,. Ltd) hereby state that all the models are electrical identical including the same software parameter and hardware design, same mechanical structure and design, the only difference is the model name. Signature:

Name: Pang Diana Title: Sales Manager 4/F, 23/B, Lianchuang Technology Park, Bulan Road, Nanwan Street, Longgang District, Shenzhen, Guangdong, China. 03/16/2023

C5266091_X8_Ed.1 Letter of Authorization Company: Shenzhen Kelvin Electronics Co,. Ltd Shenzhen Kelvin Electronics Co,. Ltd Address: 4/F, 23/B, Lianchuang Technology Park, Bulan Road, Nanwan Street, Longgang District, Shenzhen China Product Name: KRG096 Remote control Model Number: KRG096, KRG095, KRG093, KRG092, KRG091, KRG090, KRG089, KRG088,KRG087, KRG086, KRG085 FCC Identifier: 2A9SE-KRG096 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Pang Diana Date: 2023.03.15 Title: Sales Manager Signature of applicant:

1/1

US Agent for Service of Process LETTER OF ATTESTATION C566091_X23_Ed2 TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:

Company Name: FCC US Agent, LLC FRN: 0033402884 Contact Name: Tim Payne Address: address of agent: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Telephone 708-571-3148 Email: Support@FCCUSAgent.com This letter is to confirm that the US Agent for Service of Process accepts responsibility to act as a local representative on behalf of (Shenzhen Kelvin Electronics Co,. Ltd). The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. Applicant:

Company name: Shenzhen Kelvin Electronics Co,. Ltd Product Description: KRG096 Remote control Grantee code: 2A9SE FCC ID: 2A9SE-KRG096 Contact Name: Pang Diana Address: 4/F, 23/B, Lianchuang Technology Park, Bulan Road, Nanwan Street, Longgang District, Shenzhen China Telephone No: 18878479860 Email: sales2@cnkelvin.com The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. This Agreement is valid until (Product lifetime). Date: 2023/03/15 Applicants Name: Diana Pang Title: Sales Manager Signature US Agents Name: Tim Payne Title: Manager Signature 1/1