Polaroid Caution: Any changes or modifications not exerassly approved could void the user's authority to operate the equipment Fcc Part 15:
This device complies with Part 16 of the FCC Rules. Operation is subject to the folowing two conditions:
(11 This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undersired operation. Note: This equipment has bean tested and found to comply with the limits fora Class 8 digital device, pursuant to pat 15 of the FCC Files, These limits are designed to provide reasonable protection against harmful interference ina residential Instalavon Tis equipment generates, uses and can racate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to racio cornmunications, rowever, there i no guarantee that intererenos wil rot occur In particular instalation. I ths equipment does causo harmful interference to radio or television reception, whigh can be determined by furning the equipment of and on, tne User is encouraged to try to correct the interference by one oF more ofthe folowing MessUres:
+ Reotient or relocate the receving antenna
+ Increase the separation between the equipment and receiver
+ Connect the equinment into an outlet on a circuit ffeent from that to which the receiver is connected.
+ Consult the dealer or an experienced radio/TV technician for help, PLR IP Holdings, LLC, its licensees and affiliates, fully support all electronic waste iniatives. As responsible stewards of the environment, and to avoid Volating established laws, you should propely cisoose o this product in-camplance with al appteabie regulations, directves or other governanices in tno area wire you roside. Please Check wit local authorttes or the etalr where you purchased this product to determine a locaton where youcan appropriately cisnose of the product. Intany asogeiabentanty eM sh fifo Sus aod SURioBd Cosy Sse ogi vou Tow youve purehased 3 pr ho orem te bes reeeeae ease oe eS UST aA Powering ON/OFF To turn the headphones ON, long press the [Pil] button. To turn the earbuds OFF, long press the [PII] button. Adjusting Volume Long press the [>1] button to increase volume. A tone will be heard if you attempt to increase the volume past maximum level. Long press the [I<] button to decrease volume. Answering/Ending Phone Calls To answer an incoming phone call, quick press the [Pll] button To end a phone call, quick press the [PII] button, again. Playing Media To enjoy music on your headphones, make sure you are paired to a Bluetooth-enabled device. Once paired, you can control media playback and volume adjustment with the controls on your paired device on with the headphones. Playing/Pausing Media To pause media playback, press the [>I] button. To resume media playback, press the [Pll] button, again. Skipping Tracks To skip to the previous track, quick press the [I<] button. To skip to the next track, quick press the [>1] button. Gn SES Co Qn THE ARMBAND Remove any protective case on your phone and slide into the opening on the back of the armband. Slide the velcro strap up through the A slot on the armband and then back down through the B slot. Put your arm through the armband and adjust, then velcro to secure. NOTE: The armband will fit most 5 phones. Using the Armband Lights Press the [] button on the arm band to cycle through the armband LED modes. This product as supplied and distributed new by AIT, Inc. (AIT) to the original consumer purchaser is warranted by AIT against defects in material and workmanship for a period of one year from your date of purchase ("Warranty") in the unlikely event that this product is defective, or does not perform praperly, you may within one year from your original date of purchase return it to the authorized service center for repair or exchange. TO OBTAIN WARRANTY SERVICE:
* Call the Customer Support number located below, or go to our website portal to receive an SRO number. Provide proof of the date of purchase within the package (dated bill of sale)
* Prepay all shipping costs to the authorized service center, and remember to insure your return
* Include a return shipping adress (no P.O. Boxes), a telephone contact number, and the defective unit within the package. Describe the defect or reason you are returning the product. Your product will be repaired or replaced, at our option, for the same or similar model of equal value if examination by the service center determines this product is defective. Products received damaged as a result of shipping, will require you to file a claim with the carrier. The shipping address of the authorized service center is:
AIT, Inc. ATTN: Customer Service (2nd Floor) 14- 53rd Street Brooklyn, NY 11232 IN NO EVENT WILL AIT, ITS MANUFACTURERS, DISTRIBUTORS OR PLR IP HOLDINGS, LLC BE LIABLE FOR ANY INCIDENTAL, DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS, BUSINESS, SAVINGS, DATA OR RECORDS) RELATED TO THIS PRODUCT. EXCEPT AS STATED HEREIN, NO OTHER WARRANTIES SHALL APPLY. silage,
-877-768-8481 Questions? sri asa Need some hi www southerntelecom.com Chek ond Sep Gia riwtOoOoOCtCO Polaroid Bluetooth Headset PBTS7 | USER MANUAL Awestions?
feed some help?
wp re 1-877-768-8481 Taig oO ~~
a Bluetooth Headset Micro USB Charging Cable Armband eT TTD ae 1. [lq] Button:
Long press - Decrease volume Quick press - Skip to previous track 2. [>I] Button:
Long press - Power ON/OFF Quick Press - Play/pause, Answer/end phone call 3. [>i] Button:
Long press - Increase volume Quick press - Skip to next track 4. LED Indicator (Inside ring of headpiece) 5. Micro USB Charging Port (Underside of headpiece)
(Armband) 6. [ ] Button - Turn ON/OFF LEDs 7. Key Pouch UL Lae dU To charge the earbuds, attach the small end of the micro USB cable to the micro USB charging port. Attach the large end to a USB adaptor, battery pack, or USB port on a computer. The LED indicator will turn RED while charging and turn blue when charged.
(Bottom of headpiece) Zo) Juma co SS Ua a SLY 1. Long press the [>I] button. The LED indicator beneath it will quickly flash RED and BLUE 2. Set your Bluetooth-enabled device to search for Bluetooth devices. When the Bluetooth-enabled device finds the speaker, select PBT97" from the list of found devices. 3. After a successful pairing, a tone will be heard indicating that the device is paired and the LED indicator will slowly flash BLUE. On an Apple or Android
* Go to Se FINGS >
BLUETOOTH
(Make sure Bluetooth is turned ON)