FCC ID: 2AZ9V-A6 5-inch car wireless back-up camera

A6 Digital Wireless Backup Camera &

Monitor Kit Product Manual / Installation Instructions Please read this manual thoroughly before operating the device, and keep it for future reference. 1. Useful accessories:

Thank you for buying our camera. In return for your purchase, we would like to offer you a useful accessory. 2. Certificate:

Waterproof This system was certified by: CE & FCC & EMC & RoHs &

3. Package Includes:

Wireless License Plate Camera 5 inch Monitor Power Cords (2) Bracket Cigarette lighter adapter T-Taps (2) Split connector adapter Antenna Screws Instruction manual 4. Working Range:

and minivans. This system is designed mainly for cars, trucks, campers, SUVs, vans, Vehicles under 33FT---High-Speed Driving Observation Vehicles under 40FT---Slow-Speed Driving or Reversing If your vehicle is too large or you encounter signal issues, please contact us immediately and we will provide a solution. 5. Before installing, read the information below:

1) Please note the acceptable power supply voltage input to the monitor and camera. Monitor: Voltage range 9V-35V Camera: Voltage range 9V-24V Note:

1. If the power supply exceeds 24V it will cause the damage to the camera. We recommend DC 12V to the monitor and camera. 2. If the positive and negative poles are reversed, the camera will be burnt out 2Before installation, you must test the device. Please reference the image below. A. Plug power cords to the monitor and connect the power wires to camera (red-red, black-black). B. Loosen the screws on green adapter, then insert the red wire

(copper wire) to the Positive(+) slot, and the black wire(copper wire) to the Negative(-) slot. C. Plug in the cigarette lighter and turn on the red switch. If you see an image on monitor, it means that the display is functioning properly. Tips Test to make sure that your surroundings appear/display on the monitor screen! Once you have confirmed the monitor works, you are ready to install it. If there is no image after you have installed the unit, check your connections to the power source. PLEASE NOTE: if you reverse the positive wire and negative wire, it will damage the camera so be cautious. If you cannot verify which wire is positive, connect the white wire to ground it (attach it to a metal part on vehicle) and then test the positive wire. Grounding it will protect the camera. 6. Attach waterproof antenna Identify the thin wire that connects to the camera (see below sample image). This is the waterproof antenna. Since it is waterproof, you can affix the antenna to the inside or outside of the vehicle and it will not be affected by water or rain. We recommend attaching it near the license plate. If your vehicle is quite long, the signal may not be powerfully enough to reach the monitor so you may have to position it closer for better transmission. 7. Wires connection Please pay attention to the positive and negative poles of the wire. If the positive and negative poles are reversed, it may surge and cause the monitor to smoke. If the monitor is emitting smoke, please turn off the power immediately and contact customer support.

(1) The monitor can be powered by a cigarette lighter.

(2) The camera can be powered by one of two methods. a) If you plan to use the camera only when backing up, power it by attaching it to the backup/reverse tail-light of your car. b) If you plan to use the camera continuously (while driving and reversing), power it by connecting it to the running light/tail-light (the lights that is on continuously while driving). If you have questions about this step or the power supplies in your specific car make/model, email us.

(3) We have also provided an additional power cord that can be connected to the ACC/Fuse/Radio etc. to power the monitor TipsRed wire to positive pole, black wire to ground. Note :

1. If you supply power to the cigarette lighter, please turn off the power through the red button of the plug when you are not use the system. Failure to do so will cause the monitor to drain the battery on the vehicle. 2. If there is no image after your installing, please check the connections of power source. Or if you reversed the positive wire and negative wire, caused the no image. Please be cautious. If you cannot verify which wire is positive, you can connect the white/Black wire to ground (metal part on vehicle), then to test and connect the red wire to one of the back up light wire, if there is image appear on screen,it means you did correctly. 3. In the light wires of most cars in the US, the red and black wire do not represent the positive and negative poles. Many times the black wire of the car lights is the positive pole, and the green or white wire is the negative pole. please check it before installation. If the wrong wire is connected and there is no image when connected, it means that the positive and negative poles are connected reversely. Need to unplug the power immediately and reconnect correctly. Otherwise it will burn the camera. 8. Installation Video and Signal Repairing . See the following link to watch an installation instruction video on YouTube: https://youtu.be/NJDAwiPhteI If the code doesnt work, you can search the video ID on YouTube:

NJDAwiPhteI or Video name: AMTIFO A6 Wireless Rear View Camera System Operation Video on www.youtube.com or email us for help with the link. II. Signal Pairing The system signals between the camera and the monitor arrive already paired. If the signal is good, do not not attempt to pair it again yourself. If you lose signals or if you change the camera and the signal needs to be re-paired, read the below. Pairing Steps:

Step 1 : Make sure the camera and monitor are powered on. Step 2 : Touch the Menu'' button of the monitor into menu mode until Pair appears on the monitor, then press the ''+'' button to pair the signal . Step 3 : Wait for the image appearing . 9. The camera is made of waterproof material IP69 Waterproof 10. Camera Installation The bracket of the camera is designed to attach to the license plate front or hide behind it on the back. 11. We have included T-Taps adapters to better protect the cord of the reversing back-up light or tail light. Reference the picture below for easier installation. Step 1 : Plug the power cord of the reversing lamp line (back-up light cable) into the first hole of the clamp. Step 2 : Put the backing auxiliary wire into the second hole of the clamp (the hole is blocked to prevent the wire pushing/leaking through) Step 4 :Its done!

Step 3 : Clamp the adapter, and clamp the iron sheet to the bottom.

(Note: The color of T-Taps may differ from the below image) 12. 5 Inch Monitor Details & Installation The monitor can attach to the dash or windshield (depending on your preference). The button of the Monitor 1 Up (+): Touch to increase 2 Menu : Touch this to enter the menu mode ( To enter the menu page, you must switch to a single screen) 3 Down (-) : Touch to reduce 4

: Guide Lines: The default guide line is on. Touch it turn on

/off guide lines and DIY guide lines. You can adjust the height and width of guide line, and move the guide line left and right. Guide Lines ON/OFF:

5 Confirm Key and switch channels quickly. Single/Split Screen: The default is CAM1. Press the + key once to switch to CAM2, and press the + key twice switch to the split screen. 13. Product function introduction:

When you press the Menu button, you will enter the Menu mode and see 4 icon with functions :

Note :

1. Touch + or - key can switch function icon 2. Touch OK key for enter or confirm change 3. Touch the menu button to exit the current function or menu ) 1) Signal Pairing ( All items was paired before shipping. Just need pair signal when the camera lost signal or you changed new camera) First icon Pairing :

Step 1 : Make sure the camera and monitor are powered . Step 2 : When you choose Pairing, the icon is yellow, touch the OK button to enter pairing mode. The icon Pairing Start appear, Then Waiting for the image appearing . (About 20 seconds 2) Second icon Picture For setting brightness, contrast and saturation When you choose 2nd icon Picture became yellow, Touch theOK button , you can see the brightness, contrast and saturation icon. and touch + or - button choose icon you want to adjust and press OK to choose it. When the selected icon turns red, you can touch + or-to adjust the data. 3) Third icon MIR-Flip :

When you choose 3rd icon MIR-Flip became yellow, touch the OK button to enter it. Then you can touch + or - to switch from mirror Rear View image, Normal front view image, vertical flip image.

(4 options) 4) Setting:

Note: When you touch OK key enter this mode, Just touch + or - to switch different functions icon. Then touch OK key again to select it

(became red icon) ,then you can touch + and - to adjust the data. After you done, touch M key quit current mode. I. Switch Language II. DELAYTIME ( This functions is useless ) III. SCANTIME (Set time for scan time for each camera channel) IV. Automatic channel switching ON/OFF (If this function is ON, the CAM1 and CAM2 will switchable automatically, SCANTIME will set for scan time for each camera. You can set it for OFF ignore this functions. 14. The protective film on the Camera and Monitor :

After you install the system, you can tear off the protective film if you would like to make the image clearer. 15. Customer service A Two Year Warranty and lifetime tech support is included with this product. (See customer service email at the front of page). Please contact us if you have ANY issues!

If any problems come up, please contact us for professional help and solutions!

Thank you!

Troubleshooting 1. After installation, you turn on the monitor and camera power without images, at the same time, the monitor turns on for five seconds and then goes black, which means something wrong with the camera. You need to check that the camera is plugged in correctly. If the camera's power cord is not connected correctly to the headlights, there is no images. Or you can touch the camera with your hand, if the camera gets hot, it's powered on; if the camera surface temperature does not change, it is not connected to the power. Then, you need to reconnect to the power. 2. If you find the image flashing all the time after you install this system. Please try to turn off the engine and keep the key in ACC, if the image does not flicker and the image starts to flicker after starting the engine, you need to add relay or filter to keep signal stable. ( BMW, Benz, VW's cars will repel foreign devices and emit interfering currents. ) 3. If you connect the camera to the headlights and your headlights are LED, it will not work. Because the LED light cannot provide a constant direct current to the camera, you will need to switch to another power source to power the camera. FCCCaution Thisd evice complies withp art 15 oft heFCC Rules. Operationiss ubject tothe following twoco nditions: (1) Thisd evice may not cause harmfulin terference, and (2) thisd evice must accept any interferencer eceived, includingin terference thatm ay cause undesiredo peration. Any Changes orm odifications not expressly approvedb yth e party responsiblefor compliance couldv oid theu ser's authorityto operatet hee quipment. Note: Thiseq uipment has beentes tedan dfo undto comply witht helim its foraClass B digital device,p ursuantto part1 5o f theFCC Rules. These limits are designedto provide reasonable protection against harmfulin terference inares idential installation. Thise quipmentg enerates uses and canrad iate radio frequencyen ergy and,if not installedan du sedin accordancewit hth ei nstructions, may cause harmful interference torad ioco mmunications.Ho wever, thereis no guarantee thatin terferencewillnot occur inap articularin stallation.If thise quipmentdoes cause harmfulin terferenceto radio ort elevision reception,w hich canbed eterminedb ytu rningth e equipmento ff and on,t heuserisencourag edto tryto correctthe interference by oneorm oreo f the followingm easures:

-Reorient orr elocate therec eivingan tenna.

-Increase thes eparationb etweenth eequip ment and receiver.

-Connect thee quipmentinto ano utleto nac ircuitd ifferent fromth at towh ichthe receiverisc onnected.

-Consultth e dealer oran experiencedrad io/TV technician forh elp. This equipmentcom plieswithFCC uncontrolledenviro nment. radiation exposure limits setfor thfo ran

C5266091_X10_Ed.2 Shenzhen Longhui Electronics Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2022.02.28 Subject: Request for Confidentiality FCC ID: 2AZ9V-A6 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality Short-Term Confidentiality NOTE 2 No No No No No NOTE 1 NOTE 1 No No No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, 1/1 C5266091_X10_Ed.2 Signature:

Name: LIN JIANLONG Title: CEO 1/1

C5266091_X8_Ed.1 Letter of Authorization Shenzhen Longhui Electronics Co., Ltd. Company: Shenzhen Longhui Electronics Co., Ltd. Address: Floor 6, Room 5601, Modern Window Building Annex, 1078 Huaqiang North Road, Futian District, Shenzhen, china Product Name: 5-inch car wireless back-up camera Model Number: A6, R3, D8, T4, T3, Y86, Y81, H17, H21, LH1, LH2, LH3, LH4, LH5 FCC Identifier: 2AZ9V-A6 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: LIN JIANLONG Title: CEO Date:2022.02.28 Signature of applicant:

1/1

Shenzhen Longhui Electronics Co., Ltd. Model Difference Product description: 5-inch car wireless back-up camera Model name: A6, R3, D8, T4, T3, Y86, Y81, H17, H21, LH1, LH2, LH3, LH4, LH5 Trade Name: N/A FCC ID: 2AZ9V-A6 All the model are the same circuit and RF module, only for model name. Regards Sincerely Clients signature:

Clients name / title : LIN JIANLONG (CEO) Contact information / address: Floor 6, Room 5601, Modern Window Building Annex, 1078 Huaqiang North Road, Futian District, Shenzhen, china