FCC ID: 2AKUCF08-V2 Armor Blue Shark Radio transmitter

R Armor Blue Shark INSTRUCTIONS FOR USE www.makerfire.com Disclaimer & Warning 1. Please read this Disclaimer & Warning and Safety Guidelines carefully before using our product. This product is not recommended for people under the age of 14. By using this product, you hereby agree to this disclaimer and signify that you have read it fully. You agree that you are responsible for your own conduct and any damages caused while using this product, and its consequences. You agree to use this product only for purposes that are proper and in accordance with local regulations, terms, and all applicable policies and guidelines. 2. When using this product, please be sure to strictly abide by the specification requirements and safety guidelines stated in this document. Any personal injury, property damage, legal disputes and all other adverse events caused by the violation of the safety instructions or due to any other factors, will not be MAKERFIRE's responsibility. The drone is designed for 14+

Adult supervision is always advisable with any form of flying toy Always ensure the flying area is free of any obstacles before taking off, and ensure the drone is always flying in excess of 1.5 meters from yourself and others Remove all batteries from the drone and controller when not in use Never overcharge Never leave to charge unattended Never touch the drones motors during or after its flight as they can get hot Never touch the propellers when they are rotating If the drone broken, stop using it immediately Do not dispose any parts of the drone or controller as normal rubbish, all parts should be taken to the local recycling centre The battery in the drone should never be exposed to any form of high temperature or fire Safety Guidelines 1.Check Before Use

(1).This product is not a toy, but it is a high precision drone that integrates various electronic stability and control mechanisms.Please be sure to setup this drone carefully and correctly to ensure safe,accident-free operation.

(2). Please be sure that the batteries of the drone and transmitter are clean, undamaged and have enough power.

(3). Please be sure that all the propellers are undamaged and are installed in the right orientation.

(4).Please do a thorough check of the product before each use.Check for firmness of the parts, any signs of cracks and wear of the propeller,battery power and effectiveness of the product until the issue has been taken care for. 2.Safe flight Environment Fly in Open Areas Maintain Line of Sight Fly Below 98.4 feet ( 30 m) 1.Make sure the surrounding area is free of all people,pets or other obstacles before you start to fly your drone. 2.Your drone is designed for indoor or outdoor use.However,it is not recommended to fly the drone inside if there is limited space, or outside if there is any wind. 3.Keep a safe playing distance between you and the drone all the time. 3. Use of Battery

(1) Please ensure batteries are fitted in the correct orientation as shown in the instruction manual.

(2) Avoid short circuits by fiting the batteries incorrectly, and do not crush or squeeze the batteries as this could carry the risk of an explosion.

(3) Do not mix new and old batteries as this can lead to a poor performance of the product.

(4) Dispose the used batteries carefully.

(5) Please keep dead batteries away from heat and fire.

(6) If the device is not going to be used for an extended period of time, remove batteries to prevent potential damage from battery leakage.

(7) It is recommended to only use the USB charging cable that comes with the drone to charge the battery.

(8) Don't connect the battery directly to wall outlets or car cigarette-lighter sockets.

(9)Don't attempt to disassemble or modify the battery in any way.

(10) Don't use the battery if it gives of an odor, generates heat, becomes discolored or deformed, or appears abnormal in any way. If the battery is in use or being charged, remove it from the device or charger immediately and discontinue use. Package list A B Fly Below 98.4 feet ( 30 m) Drone Controller Propeller Ax2,Propeller Bx2 USB charging cable x 1 Battery Screwer INSTRUCTION MANUAL MINI FPV GOGGLES Specification Drone Wheelbase:66mm Dimensions: 83.5x83.5x45.6mm Weight: 23g(without battery) Motor:6015 1S brushed motor Battery: Li-po,3.7v 250mAh Max Flight Time: 5 mins Operating Temperature Range: 0 to 40 C o o Frequency Table Transmitter Operating Frequency: 2.4GHz Max transmission distance: 30m Battery: 1.5V AAA Operating Temperature: 0 to 40 C o o CH1 Band A 5865 Band B 5733 Band E 5705 Band F 5740 Band R 5658 CH2 5848 5752 5685 5760 5695 CH3 5825 5771 5665 5780 5732 CH4 5805 5790 5645 5800 5769 CH5 5785 5809 5885 5820 5806 CH6 5765 5828 5905 5840 5843 Unit:MHz CH7 5745 5847 5925 5860 5880 CH8 5725 5866 5945 5880 5917 Button Short press the button to adjust the frequency function, and switch between the frequency points FR1-FR8. Drones details Antenna Propeller A

(Clockwise) Propeller B

(Counter Clockwise) Shell FPV system PCB Battery Propeller A

(Clockwise) Propeller guardrail 6015 1s brushed motor It is crucial that all the propellers are installed in the correct position

(Pay attention to the letter A or B printed underneath each propeller.) HEAD Propeller B

(Counter Clockwise) Controller functions Speed-select button Auto return button Throttle left stick Headless button Emergency Stop One key start /stop Flip Trim Right stick/

LED Trim Power swith

. Always use alkaline batteries Never mix old and new batteries 1.Unscrew the battery cover,and insert 3xAAA batteries(not included), making sure you insert them following the correct polarity as shown 2.Re-attach the battery cover 3Pcs of AAAbatteries

(not included) Charging the drone battery Plug the USB plug into the computers USB port (or the charger with a DC5V output USB port).When connected,the indicator of the USB charging cable will on.Then connect the battery to the USB charging cable. The indicator light off means it is in charging; and the indicator light on means it is fully charged.Charge takes 30-40 minutes.For safety, it's better to keep the charger in sight when charging. WARNING Do not leave the battery unattended while charging & only use the supplied battery or plug charger. Pairing your drone to the controller 1. It is recommended to connect the battery plug cable to the drone battery socket before inserting the battery into drone battery chamber. The LED on the drone will start to flash. Place the drone down on a flat surface 2. Turn on your controller. Your controller will beep once & LED light will flash power swith 3. Push left throttle up once & controller will beep once 4. Pull left throttle down once & controller will beep again. Pairing is complete once the drone lights & controller lights stop flashing Flying your drone 1. Taking Off/ landing:

Taking Off Take Off/

Landing Method 2 Take Off/

Landing Method 1 Method 1:

Press the one key start button, the propellers will rotate . Push up the throttle left stick to take off. Method 2:

Push the throttle left stick up until the propellers rotate and then push up the throttle left stick again to take off. Landing Method 1:

Press the one key stop button, the drone will land by itself Method 2:

Push the throttle left stick down until the drone land 2. Altitude & rotate:

3. Forward / backward / left / right:

Use throttle left stick to control the altitude & rotation during flight. Use throttle right stick to control forward, backward,left & right movement during flight. 4.Trimming:

If the drone sways in an unprompted direction, use the trim buttons to correct the flight:

Features 1- Forward trim 2- Backward trim 3- Left trim 4- Right trim 1 3 4 2 7 6 5 1.Speed modes:

Select between 3 speed modes:

40% speed (controller makes 1 beep);60% speed (controller makes 2 beeps);

100% speed (controller makes 3 beeps) o 2.360 Flips:

Perform 360 flips by pressing the flip button and immediately push the right stick to the direction that you want the drone flip. 3.Auto return button:

Press the auto return button, the drone will automatically return in the direction of the tail before takeoff. (Most of all, consumers must keep in mind the drone orientation before the drone takes off, otherwise the return direction of the drone will deviate.) 4.Headless mode:

In order to activate this mode,press the headless button you will hear incontinuous beeps, the drone will displace according to the direction of the stick command do not matter where the drone is pointed at. Press the headless button again,to go back to the normal mode. 5.Emergency Stop:

Press the button on the controller, the motors will stop spin immediately. Only stop motors mid-flight in an emergency situations, Doing so can reduce the risk of damage or injury. 6.One key start/stop:

Press the one key start button, the propellers will rotate. Push up the throttle left stick to take off. Press the one key stop button, the drone will land by itself 7.LED:

Press the LED button to turn off/on the lights. Resetting the drone When the flight of the drone is unstable or deviated from the left and right after take-off, the consumer can correct the gyroscope and the flight will be more stable after the correction. 1. Turn on the drone & controller, place the drone on a flat ground (it is very important), then push the left throttle of the controller up & down once to pair with the drone. 2. Then push left throttle of the controller to bottom left and right throttle to the bottom right at the same time and hold for a few seconds. This will reset the drone to its defualt settings & will be ready to fly again. Trouble flying Problem Possible cause Solution The indicator lights of the drone are flashing and does not respond to the transmitter. 1.Transmitter is not synced 1.Refer to the preparation for to the drone. FLIGHT and pair again. 2.Insufficient battery power. 2.Recharge the battery. The propellers spin,but the drone cannot take-off. 1.Insufficient battery power. 2.The propellers are installed 1.Recharge the battery. 2.Install the propellers in right in wrong orientation. orientation. 3.The propellers are distorted. 3.Replace the propellers. The drone sways sharply. The propellers are distorted. Replace the propellers. Drone cannot stay balanced in flight. 1.The propellers are distorted. 2.The motor doesnt work 1.Replace the propellers. 2.Replace the motor. properly. The drone is out of control after crashing. Six-axis acceleration sensor losed its balance after crashing. Restart and re-calibrate the drone. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Armor Blue Shark Radio transmitter LABEL AND LOCATION ModelF08-V2

(Size: L2.00cm x 1.00cm) FCC ID: 2AKUCF08-V2 DC 4.5V by 3*AAA Label Location _____________________________________________________________________________________________________

Shenzhen Makerfire Technology Co.,Ltd Agent Authorization Company: Shenzhen Makerfire Technology Co.,Ltd Address: Room 502, Panbao Building, No.7-1 Lipu Street, Bantian, Longgang District, Shenzhen, China Product Name: Armor Blue Shark Radio transmitter Trade Mark: Makefire Model Number(s): F08-V2 FCC ID: 2AKUCF08-V2 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2022-05-12 Name:

Guotao Yan Title:

Manager Company: Shenzhen Makerfire Technology Co.,Ltd

Shenzhen Makerfire Technology Co.,Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2022-05-12 Subject; Request for Confidentiality FCC ID: 2AKUCF08-V2 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description BOM Software Security Requirements External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name / Title: Guotao Yan / Manager Company: Shenzhen Makerfire Technology Co.,Ltd Address: Room 502, Panbao Building, No.7-1 Lipu Street, Bantian, Longgang District, Shenzhen, China Phone: 15622891979 Fax: /

E-Mail: 2153663150@QQ.COM