DETECTION PAERN GENERAL GUIDELINES F RINSTALLATI N electrician. by a qualified be installed The sensrshould And ensure that the oservicing obeforeinstalling electricity is switched supply the product. 2, Installation inside a glass oplastic housing will esultin a reduction of detection a reduction
. Expect of approximately 20% for every sensitivity 3mm of thickness. by speedfmotiheightof installation and 3, Detectinarea will be affected vlumeofmvin g object. with no lampshade. 4, Daylight sensor was tested on sunny environment undedifferent ambient lux level could be different weatheclimate
, season or r1ent environ Notice Application need to be adjuedto sipleasefollow match installation 1, Sensors settings may manufacturer. below instructions or contact 2,The sensor is designed for indoor use only. use for a long time may reduce Outdoor may trigger the waterproof effects. The raining or wind blowing the microwave sensor even if without human motion when outdoruse. 3m to avoid interference any two sensoshould 3, The distance between be at least with each other. or space with in a metal lighting fixture 4, When the microwave is installed sensor large reflector, for exam pie a warehouse with metal rothemicrowave will be reflected and cause the lights permanently illuminated even if without motion signal. reduce the detection aa(sensitivity solvethe problems, or Please technical manufacturer sensor the microwave contact support. to provide not close to or be blocked 5, Make sure the sensor by high density material, such metal, glass, concrete walls etc. The materials will reduce oblockmicrowave and cause false trigger. 6, Make sure there are no fans or other vibrating objects in installation area. will trigger The movements sensor as well. Initialization function:
1, ON/OFF function or 3-step dimming at 100% brightness. Aerpwero1,the sensor automatically turns on light After 1 Osec, it completely turns olight. is not able to detect the sensor movement. the initialization, During 2, 2-step dimming function:
at 100% brightness. After power on, the sensor automatically turns on light After 1 Osec, it dims the light to a low light level
(set by stand-by dim level). During sensor the initialization, the is not able to detect mve1ent. NPATTERN(F RCEILING M UNTING) I MC054V RC2
-
MICROWAVE MOTION SENSOR USERS MANUAL me k Model No.: MC054V RC2 MC054VRC2 A MC054VRC2 C C)b MC054V RC:Z B fvJ MC054VRC2D 11 SAA FEATURE Sensor parameters can be conveniently set by a remote control. upto 15nmax., suitable for warehouse Mounting use. height Waterproof sensor with IP65 rating. with 1-1 OV dimable dimming when used in combination Automatic control geas. Built-in daylight sensor. adjustable stand-alone 1-10V interface can match up with Merrytek daylight sensor harvesting. daylight MS01 and achieve application. ptional mounting brackets for different SPECIFICATINS 120/270Vac, 5 0/60Hz Input voltage 400W-lnductive Rated load e 800W-Resistiv Surge current of iad 50A%1... lOuS, 277Vac full load, cold start);
80A(50% 1....=200uS, 2TNac, full load, coldrt) DETECTI 100%/75%/50%/25%
Detection aea Hold time min/3min/5minOmin/20min/30min 55/305/1 50lux/Disable OOlux/1 5 lux/15Lux/30Lu x/50Lux/1 Daylight sense Stand-by period min/3min/5min/1 Omin/30min/+oo Os/105/1 level Stand-by dimming 10% /20% /30% /50%
Microwave detecto motion principle Sensor 5.SGHz75MHz,ISM wave band Microwave frequency Munti ng height 15m Max. Detection angle 150"(Wall installatio 360"(Ceiling installation) 0.5-3 m/s detection Motion
-35"C-55"C temperature Operating IP65 (INDO RUSE NLY) IP rating Detection area:75%,Hold time:5s, Stand-by Os, Period:
Factory Setting Disable dim level0%, Daylight Stand-by Sensor:
O V l h J K m J J L W J J I r l J d E tF J ui V JJ K h i d E J 4 m w 7 F M r HJ V u J Jm E m m r 1 J E J
!'-
Slowwlk '
... 1 1 l lR/ l T i i 1 height:1Sm Mounting I to 25%/50%when mounting sensiity
\ (NoPleasedo not set the detection
.it the helg ht of 1 Sm) INSTALLATION MC054V RC:2 A Mountedracket L E E I MC054V RC:2 B valSurface M4.0X251!1TI Sc 3 3 1X 2X M MC054VRC2 C Rotatable
"'
ox.Bnrn MC054VRC2 D Metal Bracket 4X a du
.l.
-Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: