FCC ID: 2AZBU-SM510TX Baby Monitor

service@smartbaby.info service@smartbaby.info service@smartbaby.info service@smartbaby.info CONTENT 1. SAFETY INSTRUCTIONS 1-2 2. PRODUCT OVERVIEW 3 2.1 Package list 3 2.2 Parent unit(monitor) 4-5 2.3 Baby unit(camera) 6 2.4 Icons overview 6 3. USING THE BABY MONITOR 7-9 4. FUNCTION OVERVIEW 10 4.1 Lullaby setting 10 4.2 VOX setting 11 4.3 Digital zoom 12 4.4 Split screen setting 13 4.5 Pairing the camera and monitor 14 4.6 Delet the camera 15 4.7 Setting 16-21 5. TECHNICAL DATA 22 5.1 System general 22 6. TROUBLE SHOOTING 23-24 FCC STATEMENTS 25 service@smartbaby.info service@smartbaby.info service@smartbaby.info service@smartbaby.info 1 2 3 4 5 6 7 8 9 1 Power key:

2 Pan/Tilt Long press to turn on/o the monitor; short press to screen on/o. Press the key to enter into the pan/Tilt mode. 3 Volume + / Up key:

Press Volume+ to increase the volume/ To up the camera in the Press the Brightness+ to increase the brightness/ To right the camera Pan/Tilt mode. 4 Brightness + / Right key:

in the Pan/Tilt mode. 5 OK:

6 Volume - / Down key:

Pan/Tilt mode. 7 Brightness - / Left key:

in the Pan/Tilt mode. 8 Talk to baby:

release to turn it o. Press the OK key to view/scan camera or to conrm. Press Volume- to decrease the volume/ To down the camera in the Press the Brightness- to decrease the brightness/ To left the camera

*To talk, press and hold the talk key on the front of the monitor;

service@smartbaby.info

*Bear in mind that you can't listen to your baby while you're talking to them; to listen to it, you will have to stop pressing this button. Press short Menu/Exit key the menu will pop up, and press again 9 Menu/Exit:

to EXit. MIC:

When talking to the baby, collect the voices of the parents. Power&Charging Indicator LED:

*The LED shows red when charging under the display is turn o state.

*The LED displays shows orange when charging under the turn on state.

*The LED displays shows green after the battery is fully charged. When the baby unit detects the voice, the indicator light will be on, The louder the detected sound, the more lights will light up. Display the baby's picture and the adjustment of each button function. Volume LED:

LCD screen:

Speaker:

Stand:

DC-jack:

and a socket. Note:

Hear the sound from the baby. Monitor placement stand. Reset key (under the stand):

Long press the reset button with a pin to reset the display. Charge the monitor by connecting the Power Adapter to the monitor If you want to adjust the Volume/Brightness, you have to exit the Pan/Tilt mode before you operate it. service@smartbaby.info 1 2 3 4 5 6 9 8 7 1 2 3 4 5 Light sensor Speaker 6 infrared LEDs Pair key 7 CMOS sensor DC-Jack 88 Power LED Temperature sensor 9 MIC Antenna Alert Alert volume T ime format Setting 8 0 service@smartbaby.info 3.1 CHARGING AND POWERING THE MONITOR UNIT Step1:

Charge the monitor by connecting the A/C adapter included in this package to the monitor and a socket. (It takes about 4 hours for the monitor to be fully charged). Charging: Red/orange Fully charged: Green Step2:

Use the provided AC adapter included in this package to connect the wall outlet with the baby unit. service@smartbaby.info

*Place the camera at least 3ft / 1m away from your baby. Gently press and hold the Power Button for 3s to turn on the monitor, then you can see the live view. placement of the camera.

*Follow your needs to adjust the sound, brightness, and reasonable Note:

Tips:

To use the baby monitor, you must be able to establish a radio link between the monitor and camera, and the range will be aected by environmental conditions:

*Any large metal object, like a refrigerator, a mirror, a ling cabinet, metallic doors or reinforced concrete between the baby and parent unit may block the radio signal.

*The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such as TV, computers, cordless or mobile phones, uorescent lights or dimmer switches.

*When using the other 2.4GHz product, such as wireless networks

(Wi-Fi routers), Bluetooth systems, or microwave ovens, may cause interference with this product, so keep the baby monitor away at least 5ft(1.5m) from these types of products. service@smartbaby.info 10cm 3.5 SCAN AND SWITCH THE CAMERAS Short press the OK key to switch camera view when two or more cameras are connected. Long press OK key to enter scan mode, a icon will be Scan mode on displayed at the bottom left corner of the screen for 8 seconds, The camera switch icon will displayed on the top of the screen. Each cameras video will be stay on the LCD around 18 seconds. Short press the OK key to quit the scan mode. Note: This function is only avilable when two or more cameras are paired. service@smartbaby.info 4.FUNCTION OVERVIEW 4.1 LULLABY SETTING You can soothe the baby to sleep by playing a gentle lullaby from the Press Menu / Exit key and the menu will pop up. Select the lullaby you want to play through the NAVIGATION key and OK Set playback duration and volume through the NAVIGATION key and OK Press the Menu / Exit key to Exit. baby unit. Step1:

Step2:

key . Step3:

key . Step4:

service@smartbaby.info 4.2 VOX SETTING This mode allows you to control the sound activation of your baby monitor. The VOX default setting is OFF. If there is no sound around the camera within 30 Seconds, it will stop transmitting. The monitor screen turns o when the camera is not transmitting. When the camera detects the sound is louder than set sensitivity level, it will start transmitting the signal to the monitor again change the VOX level, please follow the next instructions:

Step1:

Press the Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select VOX setting . Step2:

Step3:

NOTE:

Set the VOX level through the NAVIGATION key and OK key . Press the Menu / Exit key to Exit. To resume the video and audio signal manually on your parent unit when VOX function is on, briey press any key on your parent unit. service@smartbaby.info 4.3 DIGITAL ZOOM Step1:

Step2:

Press the Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select digital zoom setting. Set the zoom scale through the NAVIGATION key, Press OK key to Step3:

conrm. Step4:

Press the Menu / Exit key to Exit. service@smartbaby.info 4.4 SPLIT SCREEN SETTING Press the Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select split screen setting. Choose single screen display or dual screen display through the NAVIGATION key, Press OK key to conrm. Press the Menu / Exit key to Exit. This function is only available when two or more cameras are paired. Step1:

Step2:

Step3:

Step4:

NOTE:

service@smartbaby.info 4.5 PAIRING THE CAMERA AND MONITOR Press Menu / Exit key and the menu will pop up. Step1:

Step2:

Press UP key or DOWN key to select pair camera setting. Select the camera to be paired through the NAVIGATION key, Press OK key or right key to to start the pairing. While the screen shows pairing then long press the PAIR button on the back of camera. Once paired, then 7 the screen will display the image from the camera. Step3:

Step4:

If unsuccessful, please repeat above steps. Press menu key to exit menu. service@smartbaby.info 4.6 DELET THE CAMERA Step1:

Step2:

Press Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select the delete camera icon. Select YES and press ok key to delete the camera. Step3:

Step4:

Press menu key to exit menu. service@smartbaby.info 4.7 SETTING 4.7.1 Temperature unit setting Press Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select the setting icon. Step1:

Step2:

Step3:

Step4:

Step5:

Step1:

Step2:

Press right key to Select , Select or , Press OK key to conrm. Press the Menu / Exit key to Exit. 4.7.2 Temperature alert setting Press Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select the setting icon. service@smartbaby.info Step3:

Press right key to Select , Set the appropriate maximum and minimum temperature, Press OK key Step4:

to conrm. Step5:

Press the Menu / Exit key to Exit. 4.7.3 Time format setting Step1:

Step2:

Press Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select the setting icon. service@smartbaby.info Select the time display format and set the appropriate time, Press OK key Step3:

to conrm. Step4:

Press the Menu / Exit key to Exit. 4.7.4 Language setting Step1:

Step2:

Press Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select the setting icon. Step3:

Step4:

Select the language, Press OK key to conrm. Press the Menu / Exit key to Exit. 4.7.5 Timer setting Step1:

Press Menu / Exit key and the menu will pop up. service@smartbaby.info Press UP key or DOWN key to select the setting icon. Step2:

Step3:

Step4:

Step1:

Step2:

Select the alarm timer, Press OK key to conrm. Press the Menu / Exit key to Exit. 4.7.6 Warning alert volume setting Press Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select the setting icon. Step3:

Step4:

Step1:

Step2:

Step3:

Step4:

service@smartbaby.info Select the alert volume, Press OK key to conrm. Press the Menu / Exit key to Exit. 4.7.7 Frequency setting Press Menu / Exit key and the menu will pop up. Press UP key or DOWN key to select the setting icon. Select 60Hz if you are in North Ameriva, select 50Hz if you are in EUROPE. Press OK key to conrm. Press the Menu / Exit key to Exit. 4.7.8 Night vision setting Step1:

Press Menu / Exit key and the menu will pop up. service@smartbaby.info Press UP key or DOWN key to select the setting icon. Step2:

Step3:

Step4:

Select the working status of night vision, Press OK key to conrm. Press the Menu / Exit key to Exit. The default setting is AUTO. If you choose OFF, the item will not enter the night vision mode even in darkness. If you choose ON, the item will always in the night vision mode. It will show black and white picture all the time. service@smartbaby.info service@smartbaby.info Product does not switch on

*Conrm that the Camera and Monitor Unit are ON(check power LED indicator).

*Conrm that Power adapters are properly connected. Reception Interference

(static)

*The camera and Monitor Unit may be too far apart.

*The battery power may be too low.

*Other electronic devices may be interfering with the signal.

*The Camera or Monitor Unit may be in close proximity to large metallic objects causing interference.

* Use of other 2.4GHz products, such as wireless networks (Wi routers), Bluetooth systems, or microwave ovens, may cause interference with this product. Keep Camera and Monitor Unit at least 5ft (1.5m) away from these items, or turn them o if they appear to cause interference.

* If the Camera Unit is too far away with low reception, move the Camera Unit closer to the Monitor Unit.

* Reset both units by disconnecting them from battery and electrical power. Wait about 15 seconds, then reconnect.

* Large metallic objects, including doors, refrigerators, mirrors, ling cabinets, and also reinforced concrete, may block the radio signal if between the Camera and Monitor Unit.

* The signal strength may be reduced when in close proximity to radio or electrical equipment, such as TVs, computers, cordless or mobile phones, uorescent lights or dimmer switches.

* Use of other 2.4GHz products, such as wireless networks (Wi routers),Bluetooth systems, or microwave ovens, may cause interference with this product. Keep Camera and Monitor Unit at least 5ft (1.5m) away from these items, or turn them o if they appear to cause interference.

* Pair the Camera Unit under a dierent channel. (chapter 4.1)

* Check all connections to the camera. Conrm that the adapter is plugged in.

* Make sure that the Camera Unit is within range of the monitor.

* Conrm that the Camera and Monitor Unit are paired.

* Volume setting may be too low. Adjust to a higher setting. Camera Unit loses link with the Monitor Unit No picture from a Camera Unit No sound from Monitor Unit service@smartbaby.info Picture is black and white

* Night vision LED may be ON. Night vision mode operates in black and white.

*Turn on room lights to force monitor out of night vision mode. The picture playback is not smooth

(choppy video with low frame rate)

* Try moving the Camera Unit closer to the Monitor Unit

* Remove obstructions between the Camera and Monitor Unit.

*Use of other 2.4GHz products, such as wireless networks (Wi routers), Bluetooth systems, or microwave ovens, may cause interference with this product. Keep Camera and Monitor Unit at least 5ft (1.5m) away from these items, or turn them o if they appear to cause interference. Noise (static, beeping)

* Battery power may be too low; recharge battery.

* Possible alarm ring alert

*Possible out of signal alert.

* Volume may be set too high on the Monitor Unit. Lower volume.

* The Camera and Monitor Units may be too close. Move them further apart.

* The Camera Unit may be too far away and out of range. Move the Camera Unit closer to the Monitor Unit.

*Make sure the Camera and Monitor Units are placed away from other electrical equipment, such as a television, computer or cordless/mobile telephone.

* The Adapter may not be properly connected

*Try using the other Adapter included. Pairing failed

* Make sure that the Adapter is connected to the Camera Unit. Try pairing to another CAM channel.

*Make sure there is no dirty on lens Noise interference on your Monitor Unit The battery will not charge Video not clear with stagnant spots/malks on the screen service@smartbaby.info service@smartbaby.info CUSTOMER SUPPORT If you encounter any problems in the process of using the product, please feel free to contact us, we will reply to you within 24 hours and resolve the issue in a way that satises you. Customer service e-mail address:

service@smartbaby.info https://www.smartbaby.info service@smartbaby.info

Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com Certification Agreement Form for Vista Certification Body Revision History Version Number Date

(mm,dd,yyyy) Comments v01 v02 v03 04/17/2018 First release (obsolete) 09/20/2018 Updating section 9 12/07/2018 Updating section 4 Certification Agreement Vista Laboratories Inc. is an independent laboratory providing testing and certification services in order to determine whether representative samples of a product comply with designated national and international standards. The applicant understands and agrees that Vista Labs has only tested or evaluated the submitted samples and does not guarantee the quality or compliance of all units of the product manufactured or produced by the applicant. Furthermore, the applicant acknowledges that as an independent laboratory, Vista Laboratories Inc. assumes no responsibility for the design of the product. The client understands that they must always fulfil the certification requirements, and implements appropriate changes when communicated to, by Vista Laboratories. The client agrees to enter into a contractual relationship with Vista Labs to perform testing or certification services on the product. Vista Laboratories does not guarantee that third parties will accept or recognize the results obtained by Vista Labs or the Vista Lab certification of the product. VIsta Laboratories agrees to perform services with due care. Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 1 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com 1. Certification Requirements The applicant will provide Vista Laboratories, Inc. with all product information for the evaluation of the product to be certified and warrant that the information provided is accurate and complete so that Vista Labs may perform the services requested. If the product was tested at an external laboratory, the applicant must provide the complete test report to Vista Labs. If the external testing facility is not ISO 17025 accredited, or does not have the proper scope, Vista Labs must determine if the test report can be used for certification activities. The applicants information is used to perform a product review and evaluation to determine the products compliance to the specific certification requested. Throughout the process, the client agrees to make claims regarding certification consistent with the scope of certification. The applicant agrees to supply the required number of product samples, to be determined by Vista Labs, to the laboratory for testing, measurement, and evaluation purposes. The client understands that certain tests may damage or destroy the sample and acknowledge that Vista Labs is not responsible for such damages. Samples will be returned only upon request by the applicant and at the applicants expense, after the completion of certification. Samples will be disposed of after six months if not requested for return by applicant. The product is ineligible for certification if it has been modified by the client after testing or certification. Changes to the product must be approved by Vista Laboratories. Vista Labs reserves the right to re-

evaluate the product as a result of information that raises questions concerning the conformance of the product. Certified products maintain fulfilment of product requirements if the certification applies to ongoing production. If the client provides copies of the certification documents to other parties, the documents are reproduced in their entirety, or as specified in the certification scheme. In making reference to its product certification in media, such as brochures or advertisement, the client complies with the requirements of the Vista Labs or as specified by the certification scheme. The client complies with any requirements that may be prescribed in the certification scheme relating to the use of marks of conformity, and on all product correspondences and product related information. Vista Labs reserves the right to revise or withdraw the requirements as required in order to maintain conformance with FCC rules and regulations governing the product. The product may continue with certification and receive certification upon demonstration of compliance with the revised requirements, to the satisfaction of Vista Laboratories. 2. Indemnification and Liability Vista Laboratories does not assume or undertake any responsibility to any other party or parties in performance of its duties under this agreement. The client agrees to hold Vista Labs harmless and to defend and indemnify Vista Labs against any liability, loss, or damage from claims, demands, costs

(including legal fees), or judgments arising out of any grossly negligent or intentional acts of the client, or client authorized third parties relating to the product. Vista Labs will not, under any circumstance, be liable to the client for any damages or third party claims which may arise as a result of the services provided in this agreement. The client understands that the opinions and findings of Vista Labs represents its judgment given with due consideration of the type of certification, the necessary limitations of practical operations, and in Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 2 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com accordance with its objectives and purpose. Vista Labs guarantees that it will perform the certification and testing services in accordance with the applicable certification requirements and recognized industry standards. The applicant agrees that Vista Labs does not warrant that its opinions or findings will be accepted or recognized by a third party. The client does not use its product certification in any way that brings Vista Labs into disrepute and does not make any statement regarding its product certification Vista Labs may consider misleading or unauthorized. The applicant agrees the distribution or promotion of a specific product utilizing a Vista Laboratories issued marking or description would mislead the public if the product is not eligible to use the marking or description, or does not comply with Vista Laboratories requirements. If a Vista Laboratories issued certification or marking is used in any manner other than as herein provided, it constitutes a breach of this agreement. A violation of any terms and conditions of this agreement may cause a temporary injunction to be issued to prevent use of the Vista Laboratories issued certification, or any references to Vista Laboratories in any manner, and a restriction from further distribution or use will be in place. The applicant agrees that Vista Laboratories has the right to subcontract the work needed for certification and/or testing. The applicant indemnifies and Vista Labs and its associated entities and personnel harmless against all losses, costs, and expenses incurred through the applicants breach of this agreement, or any negligent act or omission of the applicant in relation to the subject matter of this agreement. The client acknowledges and agrees that damages alone would not be an adequate remedy with respect to the breach of any provisions of this agreement and that breach may result in irreparable harm or injury to Vista Labs. Vista Labs is entitled without proof of special damages or specific irreparable harm or injury to the granting of equitable relief including, without limitation, injunctive relief in relation to any threatened or actual breach of any of the provisions of this agreement. This agreement shall be governed by and construed under the laws of the State of California, United States of America. 3. Confidentiality Vista Laboratories assures that confidentiality is maintained by all of its personnel and will not voluntarily disclose information obtained in confidence, unless written authorization from the client is provided or necessarily requested by the FCC. This does not apply to information that is already publicly available or acquired from other sources without restrictions on confidentiality. All documents submitted for the certification program and submitted to the regulatory authorities become publicly accessible under applicable regulations. However, under FCC Title 47 CFR Section 0.457, a special request letter may be submitted to FCC requesting for permanent confidentiality to be granted to certain allowable exhibits (schematics, block diagrams, parts, tune-up procedure, operational descriptions). The documents allowed to be held confidentially in the short-term (up to 180 days, provided the device is not marketed or sold) are as follows: external and internal photos, test set up photos, and user manual. Extensions must be requested before the end of the initially requested time frame, up to 180 days from the grant issue date. If you market before the requested time frame is over, you must notify the FCC to lift Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 3 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com the short-term confidentiality. Once the short-term confidentiality release date has been reached, these documents will be released to the public. Additionally, the following documents submitted do not qualify for confidentiality and will be released to the public automatically once application has been submitted to FCC: test reports, product label, cover letters, and attestation letters. Vista Labs assumes no responsibility for the regulatory authoritys release of documents. Documents that the applicant considers to be confidential must be designated in writing for those certification programs that will allow requested information to remain confidential. If Vista Labs is served a document requesting the disclosure of confidential or proprietary information supplied by the client, Vista Labs will promptly notify the client and cooperate with the clients needs. The responsibility for contesting the request lies solely with the client. All expenses incurred by Vista Labs will be reimbursed by the client immediately upon invoicing by Vista Labs. Vista Labs agrees that this confidentiality obligation will survive the termination of this certification agreement. For ISED applications, the client acknowledges and allows for the technical parameters referred to in section 5.5 of CB-02, as per the appropriate section in RSP-100 for the type of certification, to be posted in the Radio equipment list (REL) on the Bureau's website. For Notified Body applications, Vista Labs does not disclose any information or speak with anyone about details relating to your application, unless authorized to do so or obligated under the Radio Equipment and EMC Directives and by our Notifying Authority (NIST) as described in the next two paragraphs. As a Notified Body, we are obligated under the EMC Directive 2014/30/EU Article 34 to inform the notifying authority (NIST) of the following relevant information:

And as per Annex III, clause 8 Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 4 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com

As a Notified Body, we are obligated under the Radio Equipment Directive 2014/53/EU Article 36 to inform the notifying authority (NIST) of the following relevant information:

And as per Annex III, clause 8:

Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 5 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com 4. Compliance The applicant agrees that production of their certified product complies with and will continue to comply with Vista Laboratories requirements in their technical and administrative processes. The client adheres to compliance with all requirements of the certification process and the client agrees to make claims in respect to the certification consistent with the scope for which certification has been granted. Additionally, the client agrees to not use the product certification in any manner that would allow Vista Labs to be brought disrepute, and will not make any statements regarding its product certification that Vista Labs may consider to be misleading. The certification issued may only be used to indicate products certified by Vista Labs as in conformance with the standard applied; the client will assure that no certificate or report is used misleadingly in any form, and that copies of certification documents will be completely reproduced in its entirety. Should cancellation or suspension of product certification occur, the client immediately discontinues all advertising containing reference to the certification of the product and returns all certification documents to Vista Labs. The client must comply with all applicable regulations and requirements when making reference to its product certification in communication media such as documents, brochures, marks of conformity, advertising, etc. and comply with any requirements that may be prescribed in the certification scheme relating to the use of marks of conformity. Only the holder of the certificate has the right to use the mark of conformity. No transfer of this right to any other party is permitted. Vista Labs provides specific information or explanation to applicants for a specific scope of accreditation desired that is related to a specific scope of accreditation held by Vista Labs, and will provide additional certification application information, when requested by the applicant. Vista Labs exercises the control as specified by the certification scheme over ownership, use and display of licenses, certificates, marks of conformity, and other mechanisms for indicating a product is certified. Incorrect references to the certification scheme or misleading use of licenses, certificates, marks, or any other mechanism for indicating a product is certified, found in documentation or publicly, is dealt with by suitable action. Possible actions may include, but are not limited to: withdrawal of certificate, publication of the transgression, or legal action. In the event of an investigation of non-compliance, the certificate holder will be asked to provide records of the quality control process and any relevant information that would help to identify the cause and extent Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 6 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com of the non-compliance. All certificate holders are expected to be able to demonstrate the quality control process used for production inspection and testing, in accordance with good engineering practices. Vista Labs inform certificate holders of ISED's requirements for labelling certified equipment with the assigned certification number, as specified in RSP-100. The manufacturer, importer, or distributor shall meet the labelling requirements of Section 3 the latest version of RSP-100 for products certified under the ISED regulatory requirements of Canada. For all notified body applications, the manufacturer is required to:

Always comply with the relevant provisions of the EU Directives;

Make claims regarding EU-Type Examination/Statement of Opinion only in respect to the scope for which the certificate has been issued;

Not use its EU-Type Examination/Statement of Opinion Certificate in such a manner as to bring the Notified Body into disrepute and does not make any statement regarding its certificate on which the Notified Body may consider misleading or unauthorized;

Discontinue its use of all advertising matter that contains any reference to EU-Type Examination/Statement of Opinion and returns any EU-Type Examination/Statement of Opinion documents as required by the Notified Body upon suspension or cancellation of certificate;

Reproduce copies of the EU-Type Examination/Statement of Opinion documents, provided to others, in their entirety or as specified in the EU-Type Examination/Statement of Opinion scheme;

Ensure that reference to its EU-Type Examination/Statement of Opinion in communication media such as documents, brochures or advertising, complies with the requirements of the Notified Body;

Ensure that product markings and references to the EU-Type Examination/Statement of Opinion meet the requirements of EU Directives;

Keep a record of all complaints made known to the supplier relating to a products compliance with the requirements of the relevant standard and to make these records available to the Notified Body when requested;

Take and document appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for EU-Type Examination/Statement of Opinion;

Endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner;

The Manufacturer must notify us of any changes made to this product that might affect the compliance of this device. 5. Notification of Changes The client informs Vista Labs of any changes that may affect its ability to conform with the certification requirements immediately, upon its discovery. Changes can include but are not limited to: legal/ownership, modifications to the product or method, changes to the quality system. The manufacturer shall inform the notified body that holds the technical documentation relating to the EU-

type examination certificate of all modifications to the approved type that may affect the conformity of the radio equipment with the essential requirements of this Directive or the conditions for validity of that certificate. Such modifications shall require additional approval in the form of an addition to the original EU-type examination certificate. Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 7 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com When the certification scheme introduces new or revised requirements that affect the client, the Vista Certification Body ensures these changes are communicated to all clients. Vista Certification Body verifies the implementation of the changes by its clients and take actions required by the scheme. 6. Suspension, Withdrawal or Termination of Certification In the event that Vista Labs detects a deviation from Vista Labs requirements, Vista Labs reserves the right to take action as necessary, including suspension of the certification. Upon the clients failure to comply with any of the requirements of this agreement, Vista Labs may to issue a letter of suspension which shall notify the client of the nature of the failure. In the event that corrective action is not taken to resolve the issue, the agreement shall be terminated. In the United States, only the FCC can withdraw or dismiss issued Grants. Vista Laboratories reserves the right to withdraw or cancel any certifications issued by Vista Certification Body due to mistakes, client request, or authority request. In the case of alterations of the bases of testing and/or the prerequisites of certification or infringements, on the part of the applicant, of the rules of the certification system, Vista Labs has the right to terminate the certificates at any time. In serious cases, it may declare the certificates invalid with immediate effect. Upon suspension, withdrawal, or termination of certification, the client discontinues its use of all advertising that contains any reference to the certification scheme and takes action as required by the certification scheme, such as return of certification documents) and takes any other required measure. 7. Revision of Requirements If a regulatory amendment or revision applies to a Vista Labs certified product covered by this agreement, Vista Labs will use its best effort to inform the applicant, though it is the applicants sole responsibility to take note of the changes and to take the appropriate action if and when necessary. If the applicant agrees to accept the revision and provided the results of any supplementary examination are favorable, a supplementary authorization will be issued, or other modifications to VIsta Labs records will be made. If the applicant does not agree to accept the revision, or the results of any supplementary examination are not favorable and the applicant does not fix the problem(s), the certification covering the specified product shall cease to be valid on the date the revised specification becomes effective. 8. Complaints, Disputes, Appeals The applicant shall maintain all complaint records pertaining to a products compliance with requirements and make those records available to Vista Laboratories upon request. The applicant shall take appropriate action with respect to such complaints and deficiencies found in products that affect compliance with the requirements for certification, and record all actions taken. Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 8 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com Vista Labs and the applicant will attempt to resolve any disputes that arise. If resolution is not possible, the dispute will be appealed to the specific regulatory authority as the final arbiter. The client and Vista Labs will be allowed reasonable time to comment before the regulatory authority reaches a decision. 9. Surveillance The client makes all arrangements for the conduct of the evaluation and surveillance, including provision of personnel, examining of documentation and records, access to the relevant resources, clients subcontractors, location, and equipment. Vista Laboratories must carry out post market surveillance activity per the certification scheme, which determines if products certified by Vista Labs continues to comply with regulatory standards and rules, as well as Vista Labs terms and conditions. This is mandatory per FCC KDB 610077. Samples may be requested at any time by Vista Labs. The client agrees to provide Vista Labs a complete production product sample(s) with users guide at clients expense. The number of samples is to be determined by Vista Laboratories. The samples will not be returned unless specifically requested by the applicant and all return costs to be paid by applicant. There are no additional fees for the applicant associated with post-market surveillance testing. Please make provision to have production samples available for at least one year after the last production date. If a product fails to comply with the applicable requirements during an audit conducted by the Vista Labs, Vista Labs shall immediately notify the certificate holder and the ISED Bureau. The information submitted to the Bureau shall include a copy of the certificate that was issued for the subject equipment. As an A2LA accredited certification body, the client commits to providing, on request, access to A2LA assessment teams to assess the certification bodys performance of certification activities at the client site. 10. Fees The applicant shall pay Vista Labs the service fees as defined and stated in the supplied quotation for services. Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 9 of 10 Vista Laboratories, Inc. 1261 Puerta Del Sol San Clemente, CA 92673 Phone: (949) 393-1123 Web: www.vista-compliance.com Email: info@vista-compliance.com This agreement, made on ___2022-4-28_______, between Vista Laboratories Inc. and Shenzhen Mingchuangzhilian Technology Co., Ltd is effective on the date shown and remains in force unless one party provides written notice to the other party. Termination of this agreement shall not affect any liability of the parties existing as of the date of termination. Agreement is issued in duplicate and signed by authorized representatives of Vista Laboratories, Inc., and the client. Certification Body Information Client Information Company Name:

Vista Laboratories, Inc. Company Name: Shenzhen Mingchuangzhilian Address:

1261 Puerta Del Sol Technology Co., Ltd San Clemente, CA 92673 Address: 4/F, B Block, No.3, East Region, Shangxue Science Park, Bantian St, Longgang Dist, Shenzhen, Name Date Title Signature

. China Samb Shuai Name 2022-4-28 Date Manager Title Signature

. Date: 12/07/2018 VCB_F-09: Certification Agreement Form Version: v03 Page 10 of 10

Shenzhen Mingchuangzhilian Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AZBU-

SM510TX Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type 1. Block Diagram, 2. Schematics, 3. Operational Description File Name 1. 2AZBU-SM510TX-Block diagram 2. 2AZBU-SM510TX-SCH 3. 2AZBU-SM510TX-Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for an initial period of xxxx (ie- 45, 90 or 180) days:

Exhibit Type N/A File Name N/A Signature:

Contact name: Samb Shuai Company name: Shenzhen Mingchuangzhilian Technology Co., Ltd Address: 4/F, B Block, No.3, East Region, Shangxue Science Park, Bantian St, Longgang Dist, Shenzhen, China Date: 04/17/2018 VCB_F-01: Operating Procedures Form FCC Confidentiality v02 Page 1 of 1

Shenzhen Mingchuangzhilian Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2022-4-28 SUBJECT: FCC Application for (FCC ID:2AZBU-SM510TX) To Whom It May Concern:

We, the undersigned, hereby authorize Yoyo Zhou in Shenzhen Huaxia Testing Technology Co., Ltd at 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen Huaxia Testing Technology Co., Ltd on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely,

(Must be signed by the person that is listed on the FCC Website) Signature:

Contact name: Samb Shuai Company name: Shenzhen Mingchuangzhilian Technology Co., Ltd Address: 4/F, B Block, No.3, East Region, Shangxue Science Park, Bantian St, Longgang Dist, Shenzhen, China Date: 04/17/2018 VCB_F-01: Operating Procedures Form FCC Authorization v02 Page 1 of 1

Shenzhen Mingchuangzhilian Technology Co., Ltd Model Confirmation Letter We, (Shenzhen Mingchuangzhilian Technology Co., Ltd) certify the product:

Baby Monitor Model No.: SM510,SM510TX,SM50,SM50TX,BBM01,BBM01TX,BBM02TX Their electrical circuit design, identical,Only the model is different. layout, components used and internal wiring are Signiture:

Grantee Contact: Samb Shuai Company Name: Shenzhen Mingchuangzhilian Technology Co., Ltd Date:2022-4-28