FCC ID: 2A687BEAGLE Camera for 3d printer

BEAGLE CAMERA Quick Guide Manual PACKING LIST Beagle camera Power Plug x1 Type C Cable 1.5M x1

(For power) USB-Micro-B Cable 1M x1

(Connect to printer) Quick Guide Manual Micro SD Card x1 Reset Needle x1 Quick Guide Manual x1

(Insert in camera) SPECIFICATION Part Number Beagle Night Version Yes Frame Rate Up to 25fps Upload Printable File Yes, Only gcode files Compatibility of 3D Printers Marlin firmware Videos/Printable Files Storage Micro SD Card Connect to Printer USB Cable Video Compress H.264/H.265 Camera Resolution Up to 1080P Auto Time-lapse Video Yes Temperature Monitor Yes, for Hot End & Hot Bed WiFi Connectivity Supports 2.4 GHz 802.11g/n Power Source Plug-in Weight 150g CAMERA INTRODUCTION 1 2 3 4 1 3 IR-Cut Sensor Lens 2 4 Microphone Camera Base 3 4 1 2 WiFi Printer 1 WiFi Indicator 2 Printer Indicator Solid Green:

WiFi connected Flashing Green:

WiFi disconnected Solid Red:

Printer connected Flashing Red:

Printed disconnected 3 Speaker 4 USB Socket 1 2 3 1 2 3 Type-C Socket (Power) Plug and hold for 5 seconds, and you will hear the voice of "Successfully resetting the camera", then the camera will be reset and restart. Micro SD Slot CONNECTION Connecting Cables Plug the power cable into the camera and the power adaptor, then into a power outlet, plug the USB-Micro-B Cable into the camera and the 3d printer, as shown in the figure below.

(The camera will take 1-2 minutes when power-up, don't cutoff the power during this period.) Power outlet Micro USB Connect to Printer Plug the USB-Micro USB cable into the camera and the printer, as shown in the figure above. Put on Camera You could put the camera onto the box on the printer's front side, as shown below.

*You need to purchase a USB 2.0 Hi-Speed cable if your printer is with Hi-Speed 2.0 slot. APP DOWNLOAD & REGISTRATION Beagleprint App Store Download Google Play Download APK Download Please scan the QR Code to reach the App download page, then download from App Store, Google Play or download the APK directly. After download,Click to run the app and make the registration. USE THE APP Use your phone to connect to the camera hotspot Connect the Camera to WiFi Network the After power up camera, click to run the Beagleprint app, then click + icon to add the camera. Select the AP Configuration to add the camera. Make sure the power is not being cut off during the configuration. XXXXXX XXXXXX Select your WiFi and then input the password to save the WiFi information in the app. Go to the "Setting" interface of your mobile phone to connect the camera hotspot. The camera will automatically connect to the WiFi network. Please wait for 1-2 minutes. Click the camera image to log in and then connect the camera to your printer. Click the Connect button to connect the the camera printer, then you can control the printer through the camera. to ATTENTION Please DO NOT cut off the power of the Beagle camera when it's working; DO NOT disconnect the camera from the printer when it is connected to the printer and transmit printable files through the camera for 3d printing. Otherwise, it will cause printing failure and damage the camera's firmware. In this case, the camera cannot work typically; this problem is the user problem, not a quality problem. Hence, please ensure that you cannot disconnect the camera from the power supply and the USB cable connected to the printer when the camera is working, and the 3d printer is printing. The Beagle camera only supports one printer connection for control, allowing four users to simultaneously log in and access the camera

(including mobile phone and computer users). Therefore, please make sure it's securely accessing the device to prevent bad guys from accessing the camera or printer and the environment to cause damage. At the same time, we recommend that you do not let the 3d printer perform the 3d printing work completely unattended. Please come to the printer and watch the real printing progress of the printer regularly to prevent further deterioration of the situation when an abnormal condition occurs. This camera shortens the distance between the user and the printer. The user is obliged to ensure the reasonableness and legality of the use of the product and avoid infringement of third-party rights, includ-

ing but not limited to publicity rights, intellectual property rights, data rights, or privacy rights. At the same time, since the customers' use and storage of this camera are beyond our control, we are not responsible for possible personal injury or property loss. This manual is for reference only. In any case, we have the right to modify and improve it without notifying users. If you want to know the latest instruction manual, you can go to the official website for more information. FCC WARNING STATEMENT Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:ealer or an experienced radio/TV technician for help. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC RADIATION EXPOSURE STATEMENT The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be colocated for operating in conjunction with any other antenna or transmitter. GUIDELINES OF BEAGLE CAMERA Unboxing and Setup IP Address on PC Setup for Time-lapse Video Firmwave Ungrade FAQ 3D Printers of compatibility SHENZHEN MINTION TECHNOLOGY CO., LTD Webside: www.mintion.net Distribution: sales@mintion.net Support: support@mintion.net FB Group: Mintion Official Group (Beagleprint)

FCC ID: 2A687BEAGLE Product Name: Camera for 3d printer Model Name: Beagle Width: 2cm This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation. Long: 3cm FCC ID LABEL:

Label Location:

< Shenzhen Mintion Technology Co., Ltd >

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Subject; Request for Long Term Confidentiality FCC ID: 2A687BEAGLE Date: Jun. 06, 2022 To Whom It May Concern, public disclosure indefinitely. Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Sincerely, Signature:

Name: Jackie zhang Title: Manager It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued.

Shenzhen Mintion Technology Co., Ltd Letter of Authorization Company: Shenzhen Mintion Technology Co., Ltd Address: Room 605, A Block, 2nd Building, COFCO Xiangyun Plaza, Longcheng, Longgang, Shenzhen, China Product name: Camera for 3d printer Trade name: Mintion Model name: Beagle, Beagle SE, Beagle Pro FCC Identifier: 2A687BEAGLE We authorize MiCOM LabsInc, 575 Boulder Court, Pleasanton, California94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM LabsInc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Jackie zhang Date: Jun. 06, 2022 Title: Manager Signature of applicant:

Model Difference Declaration To Whom It May Concern, We, Shenzhen Mintion Technology Co., Ltd FCC ID: 2A687BEAGLE Product: Camera for 3d printer Trade Name: Mintion Model Number: Beagle, Beagle SE, Beagle Pro All models the function, software and electric circuit are the same, only with a product color and model named different. Test sample model: Beagle. Please contact me if you have any question. Name: Jackie zhang Date: Jun. 06, 2022 Title: Manager Signature of applicant: