FCC ID: 2AN8F-MSLM2011Q Wireless power bank

Wireless power bank Instruction Manual MSL-M2011QSM-2826 Powerbank ON/OFF Button USB Output Micro-USB Input Type-C Input LED Indicator Wireless Charging Surface Features:

1. 2. 3. 4. 5. 6. Whats included:

1 x 4,000 mAh Wireless Power Bank 1 x USB to Micro-USB Charging Cable 1 x Instruction Manual 4000mAh/3.7V/14.8Wh Micro-USB input:DC 5V/2A Type-C input:DC 5V/2A USB A output:DC 5V/2A Wireless output:5W LED Indicators Press the Powerbank ON/OFF Button(1) once to view the remaining power capacity. Press the button twice to turn OFF. 100 66 34 Instructions:

1. Charging the Powerbank:

Charge the powerbank fully before usage. Connect the provided charging cable to a power source and to the micro-USB Input port(3) or Type-C Input(4) on the powerbank. Once connected the LED Indicator(5) will BLUE color when charging, once fully charged, BLUE LED will stop Charging Electronic Devices with the Power Bank:

Connect the charging cable to your mobile phone/device using the appropriate connector. Connect the USB part of the cable to the USB Output(2) port, the LED Indicator will illuminate BLUE when charging. Remove the charging cable from your mobile device when it is fully charged. Charging Electronic Devices with the Wireless Charging:

Press the Powerbank ON/OFF button(1) to turn on the wireless charging function, LED indicator will glow green when in standby mode. Place wireless charging supported mobile device on the wireless charging surface(6). The device will automatically begin to charge, LED will glow red when device is charging. Note: When wireless charging, if the LED NOT a wireless charging device or there is an object between the device and charging surface interfering with the charging. process. 2. 3.

SAFETY PRECAUTIONS:

WARNING-When using this product, basic precautions should always be followed:

Read all the instructions before use. Never store or use this product in temperatures below 32F(0C) or above 115F(45C). Do not overcharge your phone. The unit may become hot under excessive use. Remove your phone once it is fully charged. Never charge your phone for more than 7 hours at a time. The unit will only achieve full performance after 2 or 3 completed charge and discharge cycles. To reduce the risk of injury, close supervision is required when the product is used near children. Do not expose the device to moisture. Do not use the device in excess of its output rating. Overload outputs above the 1. 2. 3. 4. 5. 6. 7. 8. Do not use the device if damaged or 9. Do not disassemble the device. For professional. incorrect reassembly may 10. 11. 12. 13. or temperatures above 104F may cause explosion. use only identical replacement parts to ensure product safety. Attachments on the back of your phone can impede the effectiveness of the wireless charger, and lead to overheating. Please remove any attachments from the phone before charging on this device, attachments can interfer with wireless charging and lead to over heating. FCC Informat on This device complies with Part 15 of the FCC Rules. Caut on: Any changes or modications not expressly approved could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to whic the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and

(2)2) interference that may cause undesired operation. device must accept any interference received, including th The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. MADE IN CHINA

Label Location Size:30*15mm FCC ID: 2AN8F-MSLM2011Q This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interfer ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ShenZhen Mossloo Industrial Co.,Ltd 2020.11.4 Eurofins MET Labs 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Clients signature:

Clients name / title : Orders Cheng /Manager Contact information / address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen, China

ShenZhen Mossloo Industrial Co.,Ltd 2020.11.4 Eurofins MET Labs 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR Product Name: Wireless power bank Trademark: N/A Model Number(s): MSL-M2011Q, SM-2826 FCC ID: 2AN8F-MSLM2011Q To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the

- Block Diagram

- Schematics

- Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Clients signature:

Clients name / title : Orders Cheng /Manager Contact information / address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen, China

Shenzhen Mossloo Industrial Co.,Ltd Model Difference 2020-11-4 Product Name: Wireless power bank Trademark: N/A Model Number(s): MSL-M2011Q, SM-2826 FCC ID: 2AN8F-MSLM2011Q All the model are the same circuit and RF module, except model names. Regards Sincerely Clients signature:

Clients name / title : Orders Cheng /Manager Contact information / address: Road One No.4, Science Industrial Park, Shangxue Village, Bantian Street, Longgang District, Shenzhen, China