Water Sensor User Manual Thank you for your support Please read the user manual carefully before operating. Please keep the user manual for future reference. Network Con(cid:31)guration Add Water Sensor to Z-Wave Network The water sensor can be included to the Z-Wave network by pressing the code button. 1. Disassemble the water sensor and insert the battery into the water sensor. Make sure the device locates within the network of the Z-Wave main controller. 2. Set the Z-Wave main controller into the learning mode (see main controller's operating manual). 3. Quickly, triple click the code button, LED light (cid:29)ashes red for 5 times. 4. Water sensor will be detected and included in the Z-Wave network. 5. Wait for the main controller to con(cid:30)gure the water sensor. Note:Power to the code, the device is plugged into the power 20S can not have any operation!
Remove Water Sensor from Z-Wave Network 1. Make sure the sensor is connected to power source. Product Introduction Technical Parameters Technical Information Product Con(cid:31)guration Installation Steps 3. Fix water sensor on the holder Tips LED Color Indicator Water sensor is an intelligent security equipment that can transmit the Z-Wave network which has particular frequency. Di(cid:31)erent countries or areas, the radio frequency of Z-Wave is di(cid:31)erent. In the Z-Wave network communications, water sensor can work with any Z-Wave main controller. In the Z-Wave network communications, water sensor can send messages to the Z-Wave main controller, and realize association with other devices through the Z-Wave network. In the communication with the Z-Wave main controller, the water sensor can send messages to the Z-Wave main controller, but it can not receive messages from the Z-Wave main controller. When the water sensor is triggered, the LED light keeps on and the buzzer will make sound. The water sensor sends messages to the Z-Wave main controller at the same time, the Z-Wave main controller will display the current status of water sensor. Water sensor is battery powered, is small and can be installed easily. Flood detection Battery speci(cid:30)cation: CR2-3V x 1 Standby current: 3uA Max current: 35 mA(In Radio Transmitter MODEL) Battery life: 2 years Radio Protocol: Z-Wave Radio Frequency: 868.4MHz EU;908.4MHz US Range: up to 80m outdoor;up to 40m indoor Operation temper: 0-40 Storage temperature: 0-60 Size (D x W x H): 68mm x 68mm x 34mm When alarm triggered, LED light (cid:29)ashes in the detection area. Easily install with screws or sticker . Detecting the location of the over(cid:29)ow timely and accurately , reduce the economic losses caused by the over(cid:29)ow of water. Compatible with any Z-Wave main controller. High sensitivity and good stability. Whats in the box ?
Water sensor Holder Battery Screw Screw stopper Probe User manual 1pc 1pc 1pc 2pcs 2pcs 1pc 1pc 01 02 03 2. Set the Z-Wave main controller into the learning mode (see main controller's operating manual). 3. Quickly, triple click the code button, LED light (cid:29)ashes red for 5 times. 4. Wait for the Z-Wave main controller to delete the sensor. Restore the Water Sensor to Factory Default Settings Reset procedure will delete all information on the Z-Wave network and Z-Wave controller, and restore the sensor to factory default settings. 1. Remove the device cover. 2. Make sure the water sensor is connected to power source. 3. Press the reset button for 10 seconds, LED light (cid:29)ashes red for 1 times. 4. Release the button. Note:When the water sensor is being restored factory settings, please make sure power source is connected. Wakeup the Sensor Manual User can press button once to wakeup this sensor to send wakeup noti(cid:30)cation to controller, the Led will be blink one time. Associations This Sensor supports 4 association groups. Each group supports max 5 associated nodes. This has the e(cid:31)ect that when the sensor is triggered, all devices associated with the sensor will receive the relevant reports. Through an association the sensor may control another Z-Wave network device, e.g. siren device, wall plug, lamp etc. GROUP 1 is lifeline service that assigned to Sensor (Water leakage detector) status. It enables the sensor to send reports and readings to Z-Wave Controller or Z-Wave Gateway whenever the sensor is triggered. This Group Support:
NOTIFICATION_REPORT_V4,BATTERY_REPORT, SENSOR_BINARY_REPORT_V2,DEVICE_RESET_LOCALLY_NOTIFI CATION GROUP 2 allows for sending control commands to associated devices such as relay module, lighting, etc. This association group is con(cid:30)gured through the advanced parameters no. 7. If the sensor clears the Noti(cid:30)cation Event that a Basic Set with 0x00 is sent to the nodes associated in Group 2 in order to turn o(cid:31) the device. This Group Support:BASIC_SET. GROUP 3 allows for Send Noti(cid:30)cation to associated devices in this group. This Group Support:NOTIFICATION_REPORT_V4 GROUP 4 allows for Send Noti(cid:30)cation to associated devices in this group. This Group Support:SENSOR_BINARY_REPORT_V2 LED light The Code button Battery Buzzer Assembly mark Induction contact Holder Probe interface Induction foot Screw stopper Screw 04 Advanced Con(cid:31)guration 1. Con(cid:31)guring Alarm Duration Time This con(cid:30)guration parameter that can be used to adjust the time for beep and LED turned on when water leakage is detected. If this parameter is set to 0, the beep and LED will be turn on always until water leakage is not detected. Prefer to Figure 1. Parameter Number: 1 Parameter Size: 1 Available Settings: 0-255min Default Setting: 120min 2. Con(cid:31)gure Alarm Interval This Parameter de(cid:30)nes beep on /o(cid:31) interval time when water leakage is 1. Holder Installation Fix the holder with screws and screw stopper 2. Battery Installation 1 2 3 Open the water sensor Install the battery Close the water sensor With the detection cable, the detection range can be extended. 4.Probe installation NOTE:
1. When assembling the water sensor, please align the assembly mark. the induction contact. 1. Make sure the water sensor is in the Z-Wave main controllers network. 2. Do not install in the place near water vapor or smoke. 3. Do not install the water sensor main body and the probe in the place where water is soaked. 4. The sensor probe should be placed on the surface of the water leakage. 5. Direct association is allowed between water sensor and other Z-
wave network devices if preset association functionality. Z wave gateway does not take part in such communication. Using this mechanism, water sensor can communicate with other devices even when gateway is damaged. LED Color Led Display Status Description Blink 5 Times
(1s Interval) Power on and Not Add in Z-Wave Network Red Blink 5 Times
(500ms Interval) Blink 5 Times
(300ms Interval) Blink 1 Time Blink with Beep On/O(cid:31) Press Button tripled, Adding siren in a Z-Wave Network or Send Node Info. Power on and Already Add in a Z-Wave Network Press the Button Long Time, Reset the Plug torestore default settings;
Detect water leakage 05 06 07 07 08 detected.Prefer to Figure 1. Parameter Number: 2 Parameter Size: 1 Available Settings: 1 255min. Default Setting: 1min 3. Con(cid:31)gure First Alarm On Time Duration This parameter de(cid:30)nes beep on duration (cid:30)rst time when water leakage is detected.Prefer to Figure 1. Parameter Number: 3 Parameter Size: 1 Available Settings: 1 255s Default Setting: 60s 4. Con(cid:31)gure Alarm on Time Duration This parameter de(cid:30)nes beep on duration after (cid:30)st beep on when water leakage is detected. Prefer to Figure 1. Parameter Number: 4 Parameter Size: 1 Available Settings: 5-255s Default Setting: 5s 5. Con(cid:31)gure Alarm Enable/Disable This parameter de(cid:30)nes beep on is enabled or disabled when water leakage is detected. 0 indicate beep on is disable, but LED will be turned on when water leakage detected. 1 indicate beep on is enabled, the BEEP and LED will be turned on when water leakage detected. Parameter Number: 5 Parameter Size: 1 Available Settings: 0,1 Default Setting: 1 6. Con(cid:31)gure Water Leakage Detected Enable/Disable This parameter de(cid:30)nes the function than water leakage detect is enabled or disabled. 0 indicate disable water leakage detect, 1 indicate enable water leakage detect. Parameter Number: 6 Parameter Size: 1 Available Settings: 0,1 Default Setting: 1 7. Basic Set Level Basic Set Command will be sent where contains a value when the door/window is opened or closed, the receiver will take it for consideration; for instance, if a lamp module is received the Basic Set Command of which value is decisive as to how bright of dim level of lamp module shall be. Command:
SENSOR_BINARY_REPORT Sensor Type: SENSOR_DOOR_WINDOW Value:0x00 Parameter Number: 7 Parameter Size: 1 Available Settings: 0-99,255 Default Setting: 255 Noti(cid:31)cation Command Class Once the detector detected a water leakage, it will send NOTIFICATION_REPORT and SENSOR_BINARY_REPORT to the nodes of lifeline to inform there is a water leakage event. When water leakage is not detected, NOTIFICATION_REPORT and SENSOR_BINARY_REPORT will be sent again to the nodes in lifeline. For compliant to Z-Wave 300 Series, There also realize the Binary Sensor Command Class. NOTIFICATION_REPORT NOTIFICATION_TYPE_WATER_ALARM Noti(cid:31)cation Report Command:
Event Present:
Command Class: COMMAND_CLASS_NOTIFICATION Command:
Noti(cid:30)cation Type:
Event:NOTIFICATION_EVENT_WATER_ALARM_WATER_LEAK_DETECTED_UNKN OWN_LOCATION Event Clear:
Command Class: COMMAND_CLASS_NOTIFICATION, Command:
Noti(cid:30)cation Type:
Event:NOTIFICATION_EVENT_WATER_ALARM_NO_EVENT NOTIFICATION_TYPE_WATER_ALARM, NOTIFICATION_REPORT, Binary Sensor Report Command:
Event Present:
Command Class: COMMAND_CLASS_SENSOR_BINARY Command:
Sensor Type:
SENSOR_BINARY_REPORT SENSOR_WATER Value: 0xFF Event Clear:
Command Class: COMMAND_CLASS_SENSOR_BINARY Command:
Sensor Type:
Value: 0x00 SENSOR_BINARY_REPORT SENSOR_WATER Battery Check Command The users can also enquire the battery status of the water detector by sending BATTERY_GET command. Once the water detector receivers the command, it will return BATTERY_REPORT command. The water detector will send BATTERY_LEVEL = 0xFF command to the ZWave Controller to inform that the water detector is in dead battery status, otherwise BATTERY_LEVEL value range is 0% to 100%. Wakeup Command Class The water detector stays in sleep status for the majority of time in order to conserve battery life. The minimum wakeup interval is 300s The maximum wakeup interval is 16,777,200s (about 194 days) Allowable interval among each wakeup interval is 60 second, such as 360, 420, 480 Note: The default value is 12 hours. This value is longer, the battery life is greater. 09 10 11 12 13 14 15 16 Command Classes Guarantee This Sensor supports Command Classes as Below:
* COMMAND_CLASS_ZWAVEPLUS_INFO (V2)
* COMMAND_CLASS_VERSION (V2)
* COMMAND_CLASS_MANUFACTURER_SPECIFIC (V2)
* COMMAND_CLASS_DEVICE_RESET_LOCALLY (V1)
* COMMAND_CLASS_POWERLEVEL (V1)
* COMMAND_CLASS_BATTERY (V1)
* COMMAND_CLASS_ASSOCIATION (V2)
* COMMAND_CLASS_ASSOCIATION_GRP_INFO (V1)
* COMMAND_CLASS_WAKE_UP (V2)
* COMMAND_CLASS_NOTIFICATION (V4)
* COMMAND_CLASS_SENSOR_BINARY (V2)
* COMMAND_CLASS_CONFIGURATION (V1) 1.The Guarantee is provided by our company (hereinafter Manufacture ) 2.The Manufacturer is responsible for equipment malfunction resulting from physical defects (manufacturing or material) for 12 months from the date of its purchasing. 3.During the Guarantee period, the Manufacturer shall repair or replace any defects, free of charge. 4.In special cases, when the device cannot be r same type (e.g. the device is no longer available in the commercial o(cid:31)er), the Manufacturer may replace it with a di(cid:31)erent device which has similar technical parameters as the faulty one. Such activity shall be considered as ful(cid:30)lling the obligations of the Manufacturer. The Manufacturer shall not refund money paid for the device. 5.The guarantee shall not cover:
a. mechanical damages (cracks, fractures, cuts, abrasions, physical deformations caused by impact, falling or dropping the device or other object, improper use or not observing the operating manual);
b. damages resulting from external causes, e.g.: (cid:29)ood, storm, (cid:30)re, lightning, natural disasters, earthquakes, war, civil disturbance, force majeure, unforeseen accidents, theft, water damage, liquid leakage ,battery spill, weather conditions, sunlight, sand, moisture, high or low temperature, air pollution c. damages caused by malfunctioning software, attack of a computer virus, or by failure to update the software as recommended by the Manufacturer. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.Any Changes or modi(cid:30)cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o(cid:31) and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-ncrease the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 16 All above is for reference only, please see the subject products.