Neo_M660 User Manual Version V1.0 Shenzhen Neoway Technology Co.,Ltd Neo_M660 User Manual V1.0 Copyright Statement Copyright 2008 Neoway Technology All rights reserved by Shenzhen Neoway Technology Co.,Ltd. The trademark trademarks in this manual belongs to their owners. belongs to Shenzhen Neoway Technology Co.,Ltd. Other Clarification This specification is for system engineer, research engineer and test engineer. As the upgrading of the product version or some other reasons, well do some necessity updating to the content of this specification without advance notice. Unless we have other additional assumpsit, all statements, information and suggestions in this manual do not constitute any express or implied guarantees. Shenzhen Neoway Technology Co.,Ltd can supply all the technological support. If you have any problem, please feel free to contact to the sales representative or send E-mail to these two mailboxes:
Sales@neoway.com.cn Support@neoway.com.cn Website: www.neoway.com.cn All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 2 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 2 Total 12 Neo_M660 User Manual V1.0 Contents 1 Overview ............................................. 5 2 Figuration ............................................ 5 3 Block Diagram ........................................ 5 4 Character............................................. 6 5 Pin Definition & Encapsulation ......................... 8 5.1 Pin Definition ...........................................................................8 5.2 PCB Packaging .......................................................................9 6 General AT Commends ............................... 10 7 Call Control Commends .............................. 11 8 TCP/UDP AT Commends.............................. 11 9 Assembling.......................................... 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 3 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 3 Total 12 Neo_M660 User Manual V1.0 Revision Record Content Revised Initial version Version V1.0 Effective date 2012-06 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 4 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 4 Total 12 Neo_M660 User Manual V1.0 1 Overview M660 is an open platform that supports GSM/GPRS wireless industry module, reserved CPU resources and a wealth of hardware interface which is widely used in various industrial and commercial fields to provide high quality voice, message, data business and other functions. 2 Figuration Table 2-1 M660 Figuration Specification Description 23.6mm*23.6mm*2.6mm (length*width*height) 2.8g Specifications Dimensions Weight Overview 3 Block Diagram PA RF Section Audio Section Baseband Controller FLASH Power Manager A p p l i c a t i o n I n t e r f a c e SIM UART All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 5 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 5 Total 12 Neo_M660 User Manual V1.0 4 Character Table 4-1 General parameters Description Operating temperature
-30+70 Operating voltage Operating Current 3.5V4.3Vrecommendation 3.9V See table 4-2 and 4-3 Storage temperature Humidity range
-40+80 0%95%
Table 4-2 GSM Specifications Description Frequency Sensitivity The Maximum transmission Power Protocol AT Audio SMS Grouped Data 900/1800/850/1900
-106dBm 850/900 Class4(2W) 1800/1900 Class1(1W) Compatible with GSM/GPRS Phase2/2+
GSM07.07 Extended command sets FREFRHRAMR voice coding TEXT/PDU Point to point/cell broadcast GPRS CLASS 12 Coding scheme CS1~CS4 Mobile Station type Circuit Switched Data Supplement Service Main Processor Class B Support CSD data service Support USSD Call forwardCFB,CFNA,CFU Call waiting Threeway calling ARM7-EJ@104MHz, 32Mbits SRAM,32~64Mbits Nor Flash Reserved software 16Mbits RAM16~32Mbits Flash All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 6 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 6 Total 12 Neo_M660 User Manual V1.0 resource Reserved software resource Instantaneous Current UART x 2I2CLCDSPIMMCUSBADCPWM GPIO x 20Keypad Max 1.8A Average working Current 300mA Standby Current 2.5mA typ. All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 7 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 7 Total 12 Neo_M660 User Manual V1.0 5 Pin Definition & Encapsulation 5.1 Pin Definition The signal connection uses 28pin SMD pad of stamp hole(half hole). Note: M660 module IO interface level is 2.8V. Because the module IO uses 2.8V power supply system, the maximum input voltage of all the IO interface can not exceed the maximum 3.3V, otherwise it may damage the module IO. Considering the signal integrality designing reasons,while the external circuit use 3.3V power system the IO interface output voltage will exceed 3.3V because of overshoot phenomenon, sometimes can even reach 3.5V.Therefore,the IO pin of the module will be damaged if 3.3V IO signal is connected to 2.8V IO of the module directly. Table 5-1 M660 Pin Definition Function Description I/O Remark Compatible to 1.8/3.0V SIM card Built-in 5K pull-up resistor Signal Name VSIM SIM_CLK SIM_DATA GND SIM_RST MICP PWR Main Power DO DIO Clock of SIM card Data input & output of SIM card PWR GRAND DO AI Alternating peak voltage200mV SIM card reset Positive electrode of MIC audio input Negative electrode of MIC audio input Positive electrode of 32 earphone driving output Alternating peak voltage200mV MICN EARP AI AO Pin 1 2 3 4 5 6 7 8 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 8 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 8 Total 12 9 10 11 12 13 14 15 16 17 18 19 20 EARN Neo_M660 User Manual V1.0 earphone audio output Negative electrode of earphone audio output Low power consumption set DTR DO AO GND RING VCCIO PWR Grand DI PWR Ring output 2.8V output Reserved Reserved URXD UTXD GND Reset BACK_LIG HT 21 ON/OFF 22 23 24 25 26 27 28 ANT GND GND GND VBAT VBAT GND Reserved Reserved UART data receiving UART data transmitting DI DO PWR Grand Reset DI Working station DO indicator, output square signal of 0.5s high level, 1.5s low level ON/OFF input DI I/O antenna GPS interface RF PWR Grand PWR Grand PWR Grand PWR Main Power PWR Main Power PWR Grand 32 earphone driving output Can be supplied to IO level shift circuit, loading capacity < 50mA Used to GPRS communications and AT commands Soft reset input, low level reset High level light LEDneed to parallel connect a capacitor of 0.1uF low level pulse can change ON/OFF state, need to keep high levelRefer to chapter 6.1.3 3.5V~4.3Vrecommend 3.9V 3.5V~4.3Vrecommend 3.9V 5.2 PCB Packaging The signal connection use 74pin SMD pad.The pin is stamp hole(half hole).The pitch is 1.27mm.The PCB encapsulation we recommend is as chart 5-1.Unit:mm All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 9 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 9 Total 12 Neo_M660 User Manual V1.0 Chart 5-1 Recommend PCB packagingtopview NoteThe number in the brackets stand for coordinate figure of the pad.The original point is the center of the mudule. The number below the coordinate figure stand for shape size of the pads LxW. The top right corner and the bottom right corner is two circle regions(R=1.3).The circle regions are route keep out regions.The requirements of the wiring refer to chapter 6.6. Reliability and Testing standards 6 General AT Commends CHECK THE MANUFACTURE QUERY MODULE MODEL QUERY VERSION GET SEQUENCE NUMBER GET INTERNATIONAL SUBSCRIBER IDENTIFICATION GET SIM CARD IDENTIFICATION AT+CGMI AT+CGMM AT+GETVERS AT+CGSN AT+CIMI AT+CCID MOBILE All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 10 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 10 Total 12 Neo_M660 User Manual V1.0 7 Call Control Commends CALL ANSWERING DIALING COMMENDS HAND UP CALLS 8 TCP/UDP AT Commends ATA ATD ATH ESTABLISH PPP LINK ESTABLISH TCP LINK SEND TCP DATA CLOSE TCP LINK ESTABLISH UDP LINK SEND UDP DATA CLOSE UDP LINK 9 Assembling AT+XIIC AT+TCPSETUP AT+TCPSEND AT+TCPCLOSE AT+UDPSETUP AT+UDPSEND AT+UDPCLOSE In order to prevent the product of M660 from being affected with damp, caused by using the SMT way to perform the furnace welding, in the process of production and use of the costumer, we employ the way of damp-proof packing, such as Aluminum Foil Bag, desiccating agent, Humidity Indicator Cards, Suck plastic trays, and vacuolization. As a result the product is kept dry and its life span will be long. In order to make the SMT way easy, we use the tray to load the product. The user only needs to install it in the chip machine according to the fixed direction. M660 storage and SMT notes, please refer to <Neoway module SMT reflow production recommendation_V1.0>. All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 11 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 11 Total 12 FCC Caution Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 2 Total 11 All rights reserved by Shenzhen Neoway Technology Co., Ltd Page 12 Total 12