FCC ID: 2BEAG-TLG85B GPS Speedometer

User Guide for 85mm GPS Speedometer with Fuel Gauge Voltmeter 1.GND 2.Power +(12/24V) 3. Fuel Level Alarm(+) 4.Low Battery Volt Charging Alarm(+) 5. Water Temp Alarm(+) 6. Oil Pressure Alarm(+) 7. External Button (+) 8. Fuel Gauge Signal Install the Gauge a. Cut an 85mm (3 3/8") hole in the panel (II) allow a clearance of . behind the panel. b. Remove fastening ring (I), insert gauge from front. Tighten gauge (III) using fastening ring ( I) c. Securely fasten the GPS antenna, preferably outdoors (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signals. Connect the antenna cable to socket on the gauge. Do not cut cable. d. After turning power on, allow the gauge to sample satellite signal for 1 minute. e. All data is for reference only and should not be trusted as sole navigation source. Parameter MenuBUZZ , ODO, UNIT, OIL,PULSE Press and Hold the back button, then power on. The LCD will switch show BUZZ, ODO, UNIT,OIL, PULSE. 1. BUZZSet Overspeed Buzzer Alarm Speed Threshold LCD will showB 80Buzzer will alarm when speed more than 80km/h, press button to set from 10~240, then release button, and wait for menu to complete flashing. 2. ODO Set Total Odometer LCD will show eg. 50005000 km, press button to set from 0~ 999999, then release button, and wait for menu to complete flashing 3. UNIT Set Unit between km/h, mph, knots LCD will switch show km / h, mph, knotsthen release button, and wait for menu to complete flashing . 4. OIL(set Fuel Gauge Ohm Input Signal) LCD will show eg. o00002indicates ohm signal input range 10~180.Press button to set target input signal range depends on Table A as below. Table A o 00000 o 00001 o 00002 o 00003 o 00004 0-190 0-180 10-180 240-33 240-30 5. Switch show Fuel Gauge and Voltmeter Press and Hold on back button 2~3 seconds, to switch show Fuel Gauge in % or Voltage in volts. 6.Switch Odometer & Trip Odometer The LCD will show Total Odometer as default. Quick press the button to switch show Trip Odometer. Long Press to reset the Trip Odometer to Zero. Please noted: After setting, you should disconnect both Power+ and GND, and then reconnect the two cable, then it will save the setting. If you just cut Power +, then itll not work properly. FCC Warnning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Shenzhen Ninghui Technology Limited Unit 1102, Block C, Kaiwo Building, Shatian, Pingshan, Shenzhen China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-12-28 To whom it may concern:

We, Shenzhen Ninghui Technology Limited, hereby certify that the equipment for which authorization is sought (FCC ID: 2BEAG-TLG85B) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered

(https://www foc. gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.914(b) and (4)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 DO1 Sincerely, Nf waglin Signature Jungui Liu Manager Shenzhen Ninghui Technology Limited

Shenzhen Ninghui Technology Limited Add: Unit 1102, Block C, Kaiwo Building, Shatian, Pingshan, Shenzhen China Date: 2023-12-28 FCC ID: 2BEAG-TLG85B Dear Sir/Madam, We, Shenzhen Ninghui Technology Limited Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model:

Product name: GPS Speedometer Model no.: TLG85B, TLG85M, TNG85, TLG85, TRG85, TRG85M, TLG52N-E, TEG85, TEGS52, TLG85MP, TLG52MP, TLM85G, TLG70, TLG70-G Sincerely, Jungpalia Name/Title: Jungui LiwManager Company: Shenzhen Ninghui Technology Limited Address: Unit 1102, Block C, Kaiwo Building, Shatian, Pingshan, Shenzhen China Phone: 18123689226 Fax: N/A E-Mail: e0755@126.com

Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Jungui Liu/Manager Shenzhen Ninghui Technology Limited Unit 1102, Block C, Kaiwo Building, Shatian, Pingshan, China 18123689226 N/A ce0755@126.com Shenzhen

Shenzhen Ninghui Technology Limited Unit 1102, Block C, Kaiwo Building, Shatian, Pingshan, Shenzhen China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-12-28 To whom it may concern:

We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behaffin all matters relating to applications for equipment authorization FCC ID: 2BEAG-TLG85B including the si ing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website wwweurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 Sincerely, Jequilin Name/Title: Jungui Liu/Manager Company: Shenzhen Ninghui Technology Limited Address: Unit 1102, Block C, Kaiwo Building, Shatian, Pingshan, Shenzhen China Phone: 18123689226 Fax: N/A E-Mail: ce0755@126.com

Shenzhen Ninghui Technology Limited Unit 1102, Block C, Kaiwo Building, Shatian, Pingshan, Shenzhen 518122 China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 2023/12/27 Shenzhen Ninghui Technology Limited acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: FCC ID: 2BEAG-TLG85B):

Name and company of U.S. agent:

Wilson Tech Service LLC Physical U.S. address of agent:

1312 17th Street Suite 692 Denver 80202 United States FRN of U.S. agent:

0033402033 Email address of U.S. agent:

Wilson.Cheung.FDA@gmail.com Wilson Tech Service LLC acknowledges their obligation to accept service of process on behalf of Shenzhen Ninghui Technology Limited Shenzhen Ninghui Technology Limited with the FRN [0034659813] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. 5 0 V

, U

) 7

) d

1 1 9

. 2 _ t n e g A _ S U

l e d o m

_ 8 4 Sincerely, Signature Jungui Liu Manager Signature Wilson Cheung Manager Shenzhen Ninghui Technology Limited Wilson Tech Service LLC