GWF-5M02 PRODUCT SPECIFICATION MODEL: GWF-5M02 VERSION: V1.0 DATE: 2017-06-13 All information contained in this specification may not be changed without permission All rights reserved 1 / 13 Historical Releases Version Modified Content Writer Auditing date Department V1.0 the first version Jasmine Ning Qing 2017-06-13 Product dept. 2 / 13 4 4 5 5 5 5 9 9 9 9 10 12 12 12 12 13 13 Catalogue Catalogue 1.Product Basic Information 1.1 Product Introduction 1.2 Product Features 2 Product Basic Function 2.1 Brief Specification 2.2 Hardware Information 2.3 Software Information 2.4 Mechanical Information 2.4.1 Product Appearance 2.4.2 Product Dimension 2.4.3 RF output Connection Information 3. Approval and Certification 4.Environment Requirements 4.1 Suitable Temperature 4.2 Suitable Humidity 5. Available WLAN Channels in Major Countries 6. Disclaimer 3 / 13 1.1. Product Product Basic Basic Information Information 1.11.1 Product Product Introduction Introduction The 5M02 is a low cost and multi-use WLAN module, it adopts the latest 802.11ac technology and fully complies with 802.11a/b/g/n/ac standards. The 5M02 module designed is to focusing on wireless connection, equipped with 4/6 pin connectors, it supports USB1.0/USB2.0 interface. The module uses high-integration MAC/BBP chip and RF single chip RTL8811AU. These features deliver reliable performance, extensive application and operational excellence. Built in on-board antenna, developers also can connect 5G or 2.4G antenna. The working frequency range is in 5.8GHz/2.4GHz. Under ideal circumstance, the transmission rate reaches to 433Mbps, users can choose one of frequency to avoid wireless interference and network congestion. It has more stable wireless signal and more smooth running speed. The module is a broadband network mode, the bandwidth reaches to 80MHz, it is effective for users to avoid network delay. The module can be applied for IP camera, IP STB, GPS, TV, internet broadcast device, etc. It makes network running more fluently for voice, video, online music, internet games to deliver a better experience. 5M02 supports multi advanced encryption mode, which offers safer network environment. The 5M02 modules have extensive operational compatibility, it supports current mainstream operation system like Windows Vista, XP/7/8/10, Linux, Mac OS; All these remove trouble of compatibility. GWF-5M02 4 / 13 1.21.2 Product Product Features Features Built in on-board antenna, or connect to external antenna via IPEX. WPS supports. 802.11b: 1, 2, 5.5, 11Mbps 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n: (20MHz) MCS0-7, PHY rate reaches to 72Mbps; (40MHz) MCS0-7, PHY rate reaches to 72Mbps 802.11ac: PHY rate reaches to 433Mbps(80MHz) Support multiple encryption mode: WFA, WPA, WPA2, Personal, WPS2.0, WAPI. Equipped with 4/6 pin connector, support USB2.0/1.1 interface Built-in power consumption management function Excellent interference resistance ability System support: Windows Vista, XP/7/8/10, Linux, Mac OS NOTICE:WLANcommunicationchannelisthecommunicationchannelusedforIEEE802.11(Wi-Fi) wirelessnetworkpermittedbynationallaws.Itisdividedto2differentindependentbandsby802.11working team.Thougheachbandcanbepartitionedtoseveralcommunicationchannels,everycountryhasitsown authoritytodecidehowtousethem.YoucanrefertoCHAPTER5fordetailedinformation. 22 Product Product Basic Basic Function Function 2.12.1 BriefBrief Specification Specification Electronic Specification Main Chipset RTL8811AU Interface Standard 4/6 pin connector, support USB2.0/1.1 interface IEEE802.11b/g & 802.11n & 802.11ac1T1R mode Operation Frequency 2412MHz - 2462MHz, 5180MHz - 5240Hz, 5745MHz - 5825MHz, Antenna location hole on-board antenna, or connect to external antenna via I-PEX 3 location holes 5 / 13 Encryption mode WFA, WPA, WPA2, Personal, WPS2.0, WAPI. Typical Transmit Power
(feed point to antenna) Receive Sensitivity Operating Voltage 802.11b: 171 dBm@11Mbps 802.11g: 151 dBm@54Mbps 802.11n: 151 dBm@150Mbps 802.11ac: 111 dBm@433Mbps(AC80) 802.11b: -80+/-1dBm 802.11g: -73+/-1dBm 802.11n: -70+/-1dBm(HT20); -64+/-1dBm(HT40) 802.11ac: -80+/-1dBm(MCS0); -56+/-1dBm(MCS9) ,(AC80) 5V DC+/-5%
TX and RX status: 220mA(max) Power consumption TX status: 220mA(max) RX status:180mA(max) Physical Specification module dimension 45.0* 18.1*2.9 mm location hole size diameter: 1.0mm Weight 3.3 g 6 / 13 2.22.2 Hardware Hardware Information Information 1. Block diagram CONNECTOR J1 or J2 RTL8811AU 5G/TX 5G/RX 5G/TX/RX FEM DEX DUPLEXOR EXTERNAL ANTENNA COAXIAL CONNECTOR BUILT-IN AERIAL ANTENNA 2. 4/6 pin connector interface schematic diagram 2.4G/TX/RX 3. 4/6 pin connector interface definition and function description as below:
Pin NO. 4-pin 2.0mm pitch Description Remark J-1 J-2 J-3 J-4 J-5 J-6 TX DVDD-5V0 UDM UDP GND WPS Not available temporarily DC 5V+/-0.5V TX enable USB power Data-
Data+
GND WPS button outgoing line 3.3V, high level active 7 / 13 J2-1 J2-2 J2-3 J2-4 DVDD-5V0 USB power DC 5V+/-0.5V UDM UDP GND Data-
Data+
GND When you consider pull-up resistor (pull-down resistor), you need to think about resistor value. J1-1(TX) connects to GND by pressing SW1 button, it is at 3.3V low level active, now it doesnt support the function temporarily. SW1 2 1 TX J1-6(WPS) connect to 3.3V by pressing WPS button(SW2), it is high level active, the schematic diagram as below. SW2 VDD33 2 1 WPS The following figure us recommended schematic diagram. 8 / 13 2.32.3 Software Software Information Information The table below is for users to check the available Operation System and its version:
OS Available OS Version YES YES YES YES YES YES YES YES Windows Linux Android Mac XP Win7 Win8 Vista Win10 Linux2.6 or above Android2.6 or above 10.3-10.10 2.42.4 Mechanical Mechanical Information Information 2.4.1 Product Appearance The view of top and bottom layer of GWF-5M02 can be displayed in the following pictures 2.4.2 Product Dimension The dimension of GWF-5M02 can be referred by following picture:
9 / 13 Three location holes position map as below (dimension unit: mm):
2.4.3 RF Signal Input and Output A. Using external antenna to process signal input and output. If the I-PEX RF connection is selected, a 50 ohm external antenna connects to the module RF output via 10 / 13 an I-PEX MHF receptacle (RF connector). The profile of I-PEX connector is contained in the following picture. Note:
I-PEXinterfacecanbeweldedtothesuitablepositioninPCBA WhenweuseexternalantennaviaI-PEXinterface,on-boardantennawillinterruptsignal connection. B. Using on-board antenna to process signal input and output. On-board antenna location is as below, users can process signal input and output directly via on-board antenna, if users think that signal quality cant satisfy requirement, they can use external antenna. The peak gain is -1dBi; the average gain is -3dBi. 11 / 13 3.3. Approval Approval andand Certification Certification Certification Approval FCC CE ROHS Pre-scan undergoing Pre-scan undergoing Pre-scan undergoing 4.4. Environment Environment Requirements Requirements 4.1 Suitable Temperature Working Temperature: -10~+50 Storage Temperature: -20 ~+85 4.2 Suitable Humidity Working Humidity: 20%~85%
Storage Humidity: 20%95%
Notice:Tokeepthenormalservicelifeandensuretheexcellentworkingperformanceofourdevice, pleaseuseitandstoreitabidebyenvironmentrequirementsstrictly. 12 / 13 6.6. Disclaimer Disclaimer This SPECIFICATION document is the guidance of the installation and tentative usage of our products. Before operating the product, please read this data sheet carefully. All rights reserved. Any reproduction, translation or simplification of this data sheet in whole or in part is strictly prohibited without written permission from our company. We do not provide any guarantee about this data sheet, software or other relevant information. We solemnly state that there is no implied business warranty or commercial contract assurance in the sheet, software or other related information. The data sheet is only for operation guidance and reference; it cannot be used as basis or supplement of any other contract or duty. 13 / 13 FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 15.105 Information to the user.
(b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your bo dy. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The module should not be installed and operated simultaneously with other radios except additional RF exposure was evaluated for simultaneously transmission. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. The final end product must be labelled in a visible area with the following:
Contains Transmitter Module YWT-5M02