Specifications for RAK4600 LoRa Module WisDuo-LoRa Series Version V1.4 | November2019 www.RAKwireless.com Visit our website for more document. 13 PAGES Table of Contents 1. Overview ................................................................................................................................................ 3 1.1 Introduction ................................................................................................................................. 3 1.2 Main Features ............................................................................................................................. 3 2. RAK4600 LoRa Module .................................................................................................................. 4 2.1 Overview....................................................................................................................................... 4 2.2 BT and LoRa Antenna position ............................................................................................. 4 2.3 Block Diagram ............................................................................................................................ 4 2.4 Supported LoRaWAN Bands ................................................................................................. 5 2.5 Pin Definition & Pin Out .......................................................................................................... 5 2.6 Power Consumption ................................................................................................................. 8 2.7 Mechanical Dimensions ........................................................................................................... 8 2.8 Recommended Footprint........................................................................................................ 9 2.9 Recommended Reflow Profile ............................................................................................. 10 2.9 FCC Caution .............................................................................................................................. 11 3. Revision History .............................................................................................................................. 13 4. Document Summary ..................................................................................................................... 13 2 1. Overview 1.1 Introduction RAK4600 LoRa Module includes a nRF52832 MCU and a SX1276 LoRa chip. It has Ultra-Low Power Consumption of 2.0uA in sleep mode, high LoRa output power up to 20dB max in work mode, and BLE output power up to 4dBm. The module complies with LoRaWAN 1.0.2 protocols. It also supports Lora Point to Point communications. The Module supports BLE 5.0 in addition to LoRa. Its RF communication capabilities (LoRa+BLE) make it suitable for a variety of applications in the IoT field such as home automation , sensor networks, building automation or Personal area networks such as health fitness sensor and monitor devices ,Medical devices. 1.2 Main Features LoRa module for Smart City, Smart Agriculture, Smart Industry Compact Form Factor: 15 x 23 x 2.5 mm 42 Pin Stamp Pad for PCB SMT mounting I/O ports: UART/I2C/GPIO (optional NFC interface) Temperature range: -40C to +85C Supply voltage: 2.0 ~ 3.6V Frequency range: 863870MHz (EU) / 902928MHz (US) Low-Power Wireless Systems with 7.8kHz to 500KHz Bandwidth Ultra-Low Power Consumption 2.0uA in sleep mode Serial wire debug(SWD) 3 2. RAK4600 LoRa Module 2.1 Overview The figure below shows the top view of the RAK4600 LoRa Module. The dimensions of the Module are 15 x 23 x 2.5 mm. Figure 1 | RAK4600 LoRa Module 2.2 BT and LoRa Antenna position RAK4600 support both BT and LoRa.The picture below shows the BT and LoRa Antenna position. 2.3 Block Diagram The Block diagram below shows the external interfaces of the RAK4600 LoRa Module. 4 Figure 2 | Block Diagram 2.4 Supported LoRaWAN Bands The RAK4600 LoRa Module supports the high LoRaWAN bands (refer to the Table 1). Region Frequency (MHz) North America Indian Europe Australia Korea Asia IN865 EU868 US915 AU915 KR920 AS923 Table 1 | Operating Frequencies 2.5 Pin Definition & Pin Out The figure below shows the pin out of the RAK4600 LoRa Module. 5 Figure 3 | Pinout The table below shows the pin definition of the RAK4600 LoRa Module. Pin Name I/O Description GND NC NC I2C1_SDA I2C1_SCL NFC1 NFC2 GND
I/O I/O I/O I/O
Ground NC NC
(p0.10) Ground 1 2 3 4 5 6 7 8 9 10 I2C,General purpose I/O (p0.13) I2C,General purpose I/O (p0.12) General purpose I/ONFC antenna connection(p0.09) General purpose I/ONFC antenna connection USART2_RX I/O USART2_RX (General purpose I/O p0.18) USART2_TX I/O USART2_TX (General purpose I/O p0.19) 6 GPIO1/P0.14 USART1_RX USART1_TX GPIO2/P0.17 I/O I/O I/O I/O General purpose I/O (p0.14) USART1_RX (General purpose I/O p0.22) USART1_TX (General purpose I/O p0.23) General purpose I/O p0.17 NC GND GND GND GND RF_L GND GND GDD NC NC NC NC NC NC NC NC NC NC 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 I/O Ground RF_BT I/O BLE RF OUT I/O LoRa RF OUT NC Ground Ground Ground Ground Ground Ground NC NC NC NC NC NC NC NC NC NC
GND Ground MCU_NRST SYS_SWDIO I/O I/O MCU reset SYS_SWDIO SYS_SWDCLK I/O SYS_SWDCLK GND 3V3_IN 3V3_IN GND Ground Input power Input power Ground Table 2 | Pin Definitions 7 2.6 Power Consumption Item Power Consumption Condition Tx mode LoRa @20dBm 125mA Tx mode LoRa @17dBm 92mA Tx mode BT@4dBm 9mA Rx mode LoRa @37.5Kbps 17mA Rx mode BT@2Mbps 11.5mA LoRa @ PA_BOOST
&BT sleep LoRa @ PA_BOOST
&BT sleep BT Tx mode & Lora sleep LoRa @ Receive mode &BT sleep BT Rx mode & Lora sleep Sleep mode 2.0uA LoRa&BT sleep Table 3 | Power Consumption 2.7 Mechanical Dimensions The figure below shows the mechanical dimension of the RAK4600 LoRa Module. 8 Figure 4 | Mechanical Dimensions 2.8 Recommended Footprint Figure 5 | Recommended Footprint 9 2.9 Recommended Reflow Profile Figure 6 | Recommended Reflow Profile Standard conditions for reflow soldering:
Pre-heating Ramp (A) (Initial temperature: 150): 1~2.5/sec;
Soaking Time (T2) (150~180): 60sec~100sec;
Peak Temperature (G): 230~250;
Reflow Time (T3) (>220): 30~60 sec;
Ramp-up Rate (B): 0~2.5/ sec;
Ramp-down Rate (C): 1~3/ sec. Please contact us if you need technical support or need more information. Support center: https://forum.rakwireless.com/
Start guide and software firmware download:
https://downloads.rakwireless.com/en/LoRa/RAK4600/
Email us: info@rakwireless.com 10 2.9 FCC Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. Radiation Exposure Statement To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm from your body. 11 Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules[and ISED Radio Standards Specifications]
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular. 2.3 Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs Not applicable 2.6 RF exposure considerations body 2.7 Antennas This equipment should be installed and operated with minimum distance of 20cm from your This radio transmitter FCC ID: 2AF6B-RAK4600H has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna No. Operate frequency band Antenna Type Antenna 1 Antenna 2 902 GHz 928 GHz External Antenna 2402 MHz 2480 MHz External Antenna Maximum antenna gain 3.00 dBi 3.00 dBi The final end product must be labeled in a visible area with the following" Contains FCC ID:
2.8 Label and compliance information 2AF6B-RAK4600H 2.9 Information on test modes and additional testing requirements Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host 2.10 Additional testing, Part 15 Subpart B/ Canadian CAN ICES-003 (B) disclaimer Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B 12 3. Revision History Revision Description 1.0 1.1 1.2 Initial version Revision of parameters Revision of power consumption Date 2019-05-27 2019-10-24 2019-11-22 4. Document Summary Prepared by Checked by Approved by Hairui Penn & Vladislav About RAKwireless:
RAKwireless is the pioneer in providing innovative and diverse cellular and LoRa connectivity solutions for IoT edge devices. It's easy and modular design can be used in different IoT applications and accelerate time-to-market. For more information, please visit RAKwireless website at www.rakwireless.com. 13