FCC ID: PP23287 Wired/Wireless Gaming Mouse

RF exposure statement This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Reference No.: WTX23X06127428W001 Page 1 of 15 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2023-09-14 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref:

Attestation Statements Part 2.911(d) (5) (i) Filing SUBJECT: FCC Application for FCC ID: PP23287 To Whom It May Concern:

Shenzhen Rapoo Technology Co., Ltd certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signatory

[Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2023-09-14 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref:

Attestation Statements Part 2.911(d) (5) (ii) Filing SUBJECT: FCC Application for FCC ID: PP23287 To Whom It May Concern:

Shenzhen Rapoo Technology Co., Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Signatory

[Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2023-09-14 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: PP23287 Confidentiality Request To whom it may concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. Block Diagram Operational Description Schematics Parts List Tune-Up Information Security Information Software Defined Radio (SDR) Information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Internal Photos Test Setup Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. or For 180 days pursuant to KDB 726920 D01. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signatory

[Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2023-09-14 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: PP23287 To Whom It May Concern:

I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B device. I understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage:

https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Sincerely, Signatory

[Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2023-09-14 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: PP23287 POWER OF ATTORNEY To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Shenzhen Rapoo Technology Co., Ltd are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Signatory

[Jerry Guo, Director of Research and Development Centre]

Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Date: 2023-09-14 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 USA Ref: Attestation Statements Part 2.911(d) (7) Filing Grantee Code: PP2 Applicant FRN: 0017901232 Shenzhen Rapoo Technology Co., Ltd certifies that, as of the date of the filing of the application, Jaylusc Inc. is our designated U.S. agent for service of process for the above referenced Grantee Code. Shenzhen Rapoo Technology Co., Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Jaylusc Inc accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced Grantee Code. Designated U.S. Agent Information:

Name: Jaylusc Inc. U.S. Agent FRN: The agent for service of process does no other business with the FCC and does not have an FRN. Address: 3101 SW 116th AVE, DAVIE FL 33330 Contact Person: Julio Souto Tel.: +786 554 31264 Email: julioud@icloud.com Sincerely, Signed on behalf of Shenzhen Rapoo Signed on behalf of Jaylusc Inc. Technology Co., Ltd Name: Jerry Guo Name: Julio Souto Shenzhen Rapoo Technology Co., Ltd 22, Jinxiu Road East, Pingshan District, Shenzhen, China Title: Director of Research and Development Title: Director Centre Date: 2023-09-14 Date: 2023-09-14