1 RF-BM-S02A(BLE) Module
This module is designed to get the electronic products together with intelligent For the transplantation and use of Bluetooth Low Energy(BLE) applications in various industry products .SHENZHEN RFSTAR TECHNOLOGY CO.,LTD releases BLE transparent transmission module. The module make the host application development easier as as a bridge of smart phone peripherals. User'sexisting products or solutions with this module, can communicate with mobile devices (with Bluetooth 4.0) , realize intelligent control and management under the bridge (serial port) mode. Users can design their own solutions or products to use the module to extend simple peripherals under the direct driving mode,to release new peripherals in lowest cost and efficiency. The RF - BM S02A BLE module use TI CC2541 as the core processor with TI official standard protocol stack, which runs at 2.4 GHz ISM band, GFSK (Gaussian Frequency Shift Keying) modulation mode, with 40 channels in 2 MHz clearances, 3 fixed radio channels, 37 adaptive automatic jump frequency channels according to the passage, the Physical layer with classic Bluetooth are RF dual-mode device, The 2 MHz gap can prevent the adjacent channel interference better. The module with Wide output power regulation (- 23 dBm ~ 0 dBm), - 93 dBm high-gain receiving sensitivity in 11.2 mm x 15.1 mm x 1.9 mm. mobile devices, which can be widely applied to instruments and meters, logistics tracking, healthcare, intelligent household, sports measurement, automotive electronics, toys. The module - 93 dBm high-gain receiving sensitivity in 11.2 mm x 15.1 mm x 1.9 mm. Features:
1.Convenient, do without any Bluetooth protocol stack application experience. 2.Using universal serial to design users interface with bi-directional reading and simple operation 3.Dimensional channel design, minimize data packet processing, and maximize the communication efficiency . 4.Ultra low power consumption in standby mode. Applications:
2.4-GHz Bluetooth low energy Systems
Mobile Phone Accessories
Sports and Leisure Equipment
Health Care and Medical
Home and Building Automation
Consumer Electronics
2 RF-BM-S02A Mechanical Footprint (Unit:mm) DIMENSIONS 15.1 x 11.2 x 1.9 mm. Pin Description PIN Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 Pin9 Pin10 Pin11 Pin12 PIN name Description Remarks GND VCC P22 P21 RESET P20 P17 I2C_SCL I2C_SDA P12 P11 P07 The ground pad must be connected to a solid ground plane. Power-supply connection I/O I/O Reset, Active Low I/O I/O 2V-3.6V DEBUG_DC DEBUG_DD I2CClock line I2CData line CC2541 I2C_SCL CC2541 I2C_SDA I/O I/O I/O
3 Pin13 Pin14 Pin15 Pin16 Pin17 Pin18 P06 P05 P04 P03 P02 P01 I/O I/O I/O I/O I/O I/O FCC Warning:
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID:
2ABN2-RFBMS02A when the module is installed inside another device, the user manual of this device must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
2 FCC Warning:
This device complies with part 15 of the FCC Rules. Operation is subject to the If the FCC identification number is not visible when the module is installed inside another device, then the following two conditions: (1) This device may not cause harmful interference, and outside of the device into which the module is installed must also display a label referring to the enclosed
(2) this device must accept any interference received, including interference that module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID:
may cause undesired operation. 2ABN2-RFBMS02A Changes or modifications not expressly approved by the party responsible for when the module is installed inside another device, the user manual of this device must contain below compliance could void the user's authority to operate the equipment. warning statements;
FCC Radiation Exposure Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference. This modular complies with FCC RF radiation exposure limits set forth for an
(2) This device must accept any interference received, including interference that may cause undesired uncontrolled environment. This transmitter must not be co-located or operating in operation. conjunction with any other antenna or transmitter. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the If the FCC identification number is not visible when the module is installed inside user's authority to operate the equipment. another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2ABN2-
RFBMS02A Or Contains FCC ID: 2ABN2-RFBMS02A When the module is installed inside another device, the user manual of the host must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. in strict accordance with the The devices must be manufacturer's instructions as described in the user documentation that comes with the product Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C : 15.247 and 15.209 requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 requirementthen the host can be sold legally. installed and used