FCC ID: 2AZSW-SECTEC wifi ip camera

1080P FULL HD Baby Monitor User Manual OK +

V1.2 1.Whats Included:

OK +

1.1: Camera*1 1.2: LCD Monitor*1 1.3: Mounting Bracket*1 1.4: Power Adaptor*2 1.5: Type-C Cable*1 1.6: Micro USB Cable*1 1.7: Screws*1 1.8: User Manual*1 2.Key and Interface Introduction 1 2 3

6 1.Microphone 2.Lens 3.Photoresistance 4.Speaker 5.Power Port 6.Digital Temp Sensor 4 5 Lens 2.1: Back button: Press the button to return to the previous step, press again to enter the setting In the main menu, press the button to return to the previous menu 2.2: Camera Switch Button: Press the button to switch camera from one to the next . 2.3: Direction Button: In Monitoring Mode the button could control the Pan and Tilt of the camera. In main menu the button could select direction. 2.4: Type-C Charge Port. 2.5: OK button: Press the to enter menu and conrm on settings . Click this button under the monitoring screen to enlarge the screen 2.6: Brightness and volume buttons:Press the up and down arrow keys to adjust the brightness Press the left and right arrow keys on the button to adjust the volume 2.7: Talk Button: Press to talk while live audio o, press again to turn on live audiowhile talk function stop. 2.8: Sound Detection (VOX) Button: Press to open sound detectionOn the display will show Press again to turn o sound detection(On the display will disappear) 2.9: Power On/O Button: Long press to turn on/o the unit ,short press to enter standby mode. 2.10: External Antenna: Put the antenna up the signal will reach the best state. 2.11: Bracket 2.12: Speaker 3.Connect the camera to the Monitor 3.1: Power on the camera about 3-5 s the camera will saypower on system starting up and start to work. 3.2: Long Press the power on/o button to turn on the unit. (Tips: Kindly make sure the monitor is fully charged before connection when use for the rst time) 3.3: After camera and monitor ready wait about 10S the picture will show on the monitor then could start to use the baby monitor . 4.Add new camera 4.1: Enter the main menu and choose camera ( )choose channel Double press OK button to start matching Conguring (Pic 1) Connected (Pic 2) 4.2: If cant add the camera successfully please check if the camera is powered . If camera already been powered then please reset the camera and add the camera again according to step 4.1. 4.3: If need to connect 4 cameras then add from CH1 to CH4. Choose the channel when add cameras to the related channel.Move to the channel you want to view and press OK to switch the channel view. In preview left corner will show the channel now displaying.( ) 5.Feed Timer Setting 5.1: Enter the menu to set up Feed timer( )---up and down to select time left and right choose single time/ recycle/turn on or o the clock. 5.2: After set the feed timer you can choose single time or recycle. 5.3: If you dont need feed timer function please close the clock. 6. Sound Detection 6.1: Press OK button to enter the main menu and choose Sound detection

( ) There are low/medium/high/optional. 6.2: Press VOX button on the top will turn on press again to turn o. 6.3: When the camera detected the DB range over the settings the LCD screen will lighten up and show the icon in the middle of the screen. There will be an alarm sound like di di about 30S, if the camera keep detected sound over settings it will send alarm sound continuously. Press any button on the monitor to stop the sound alarm. 7.Temperature Detection Alarm 7.1: Temperature alarm setting could be (C) or (F) according to actual usage. 7.2: The default temperature is 18-30C once the temperature lower or higher than the range will send alarm 7.3: The temperature alarm need to be shut down manually if it keep alarm due to temperature issue. 8.Play the lullaby 8.1: Enter the main menu and choose the lullaby icon ( )could select No.1-No.6 lullabies .During the play the lullaby the information will show on the left corner of the screen. 8.2: Name of the lullaby:

Castle in the Sky Grave of the Fireies Passive Spirited Away Street of sea The Love That Transcends Time 9.Display Settings 9.1: The display settings have Dormant/ LUMI 9.2: Dormant mode default 1Min( )/10Min( )/30Mini( )

/ALWAYS ON ( ) could adjust according to actual usage. 10. Video Recording 10.1: Enter the main menu and select the record icon ( ) The record le can choose 0.5Hr/1Hr/2Hr (Means how long to pack to one le) 12.2: If dont need to record could choose OFF. 11.Video Playback 11.1: Enter the menu and select the playback icon ( )and click to pick up the time of the video you want to play. 12.System Settings 12.1: Time & Date ( )setting: System Time/Date Format/Separator/

Time Format could set according to actual usage 12.2: Back to factory settings( ) . Not suggest to use normally please contact the seller for assistant if have to. 12.3: Advance Settings( ): You can set the screen rotation, check storage capacity and remaining capacity 12.4: Version Information( ) The version information subject to the actual situation 13.Language Settings 13.1: The device support 8 language ENGLISH//JAPANESE/CHINESE/PORTUGUESE/ITALIAN/FRENCH/SPANISH/

GERMANY default is ENGLISH 13.2: Could adjust the language according to your request.After conrm the language please power o the monitor and restart .When connect the camera it will change to the language same as the monitor . Tips: When changing the language please make sure the camera is powered on. 14.Installation Steps Questions and Answers:

Q: The LCD monitor didnt show the camera ?

A: Please check if the camera is powered on . If camera is powered on please reset the camera to factory settings and add the camera according to steps 4.1. Q: There is annoying sound when use the talk function in near distance?

A: When the camera and monitor is within 2meter distance there might be some noise which is a normal Physical phenomena. You can adjust the monitor volume down or keep the camera and monitor from longer distance. Q:The monitor battery drains fast?

A:If you dont open the Dormant mode and the monitor will works all the time so the battery will run faster. Suggest to use Dormant mode with 30S or 60S to save battery. The brightness of the monitor maybe too much high could lower down the brightness to expand the standby time. Q:The transfer distance between the camera and monitor not far?

A: In an open environment the camera and monitor could transfer as far as 300meters .While for indoor use in case of interference the transfer distance will be inuenced like too many walls and wireless electronic devices . After-sales instructions:

1.Please refer to the actual product all the instructions are for reference only. 2.Product may updates in future without notice . 3.The manual contains the introduction of the basic functions of the product please operate by yourself. 4.If there is any problem when using the product please contact the supplier in time. 5.We have tried our best to ensure the completeness and accuracy of the content in the manual, but some data may still be stored with the actual products.In case of deviation, if you have any questions or disputes, please refer to the company's nal explanation. 6.In cases of any losses caused by wrong operation will be borne by yourselves. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

SHENZHEN SECTEC CO., LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2021-05-07 Subject: Request for Confidentiality FCC ID: 2AZSW-SECTEC To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Long-Term Confidentiality Short-Term Confidentiality NOTE 2 Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info No No No No No No No No No No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Musk zhang Title: Manager 1/1

SHENZHEN SECTEC CO., LTD Model Difference Product Name: wifi ip camera Model Number: ST-BM288-4.3 ST-BM289-2M-TY, ST-BM288-2M-5, ST-BM288-2M-5X2, ST-BM520-2M-4.3, ST-BM603-1M, ST-BM605-1M, ST-BM601-1M, ST-288-2M-TY-5G, ST-351-2M-TY-5G, ST-S588-2M, ST-S588-2M-4G, ST-S582-2M, ST-S582-2M-4G, ST-939-3M-TY, ST-967-3M-TY, ST-496-5M-IC, ST-495-5M-IC, ST-BC23-2M-IC, ST-326-2M-IC, ST-193-2M-IC, ST-S379M-2M, ST-393-5M-IC, ST-S588M-4M, ST-S588M-4M-4G FCC Identifier: 2AZSW-SECTEC All the models are the same circuit and RF module, except the mode names and outlook color. Regards Sincerely Clients signature Clients name / title: Musk zhang / Manager Contact information: 4/F, Building 6, Jianghao Industrial Park, No.430, Jihua Road, Bantian Street, Longgang District, Shenzhen, 518129, CN

SHENZHEN SECTEC CO., LTD Letter of Authorization Company: SHENZHEN SECTEC CO., LTD Address: 4/F, Building 6, Jianghao Industrial Park, No.430, Jihua Road, Bantian Street, Longgang District, Shenzhen, 518129, CN Product Name: wifi ip camera Model Number: ST-BM288-4.3,ST-BM289-2M-TY, ST-BM288-2M-5, ST-BM288-2M-5X2, ST-BM520-2M-4.3, ST-BM603-1M, ST-BM605-1M, ST-BM601-1M, ST-288-2M-TY-5G, ST-351-2M-TY-5G, ST-S588-2M, ST-S588-2M-4G, ST-S582-2M, ST-S582-2M-4G, ST-939-3M-TY, ST-967-3M-TY, ST-496-5M-IC, ST-495-5M-IC, ST-BC23-2M-IC, ST-326-2M-IC, ST-193-2M-IC, ST-S379M-2M, ST-393-5M-IC, ST-S588M-4M, ST-S588M-4M-4G FCC Identifier: 2AZSW-SECTEC We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Musk zhang Title: Manager Date: 2021-05-07 Signature of applicant:

1/1